Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM J

2WW ENGINE CONTROL  ECD SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the EFI MAIN NO. 1 relay coil, closing the EFI MAIN NO. 1 relay contacts and supplying power to terminal +B, +B2 and +B3 of the ECM.

WIRING DIAGRAM

A372439E03
4.125,1.156 7.135,1.427 3.01,0.271 10 false Certification ECU (Smart Key ECU Assembly)*1 1.25,1.198 3.188,1.448 1.938,0.25 10 false Ignition Switch Assembly*2 0.719,0.896 1.177,1.094 0.458,0.198 10 false AM2 1.24,1.042 1.698,1.24 0.458,0.198 10 false G4 4.125,1.01 4.583,1.208 0.458,0.198 10 false G82 5.396,0.74 5.917,0.938 0.521,0.198 10 false IG2D 1.615,0.646 2.073,0.844 0.458,0.198 10 false AM2 2.198,0.656 2.656,0.854 0.458,0.198 10 false IG2 2.5,0.646 2.833,0.854 0.333,0.208 10 false 3 1.458,0.646 1.667,0.854 0.208,0.208 10 false 4 2.625,1.667 2.833,1.875 0.208,0.208 10 false 3 3.417,1.656 3.625,1.865 0.208,0.208 10 false 5 3.417,2.031 3.625,2.24 0.208,0.208 10 false 1 2.635,2.042 2.844,2.25 0.208,0.208 10 false 2 1.927,1.906 2.385,2.104 0.458,0.198 10 false IG2 1.385,4.052 2.625,4.292 1.24,0.24 10 false EFI MAIN 3.094,4.563 4.333,4.802 1.24,0.24 10 false EFI MAIN NO. 1 3.146,4.125 3.354,4.333 0.208,0.208 10 false 2 3.938,4.115 4.146,4.323 0.208,0.208 10 false 1 3.156,3.729 3.365,3.938 0.208,0.208 10 false 5 3.948,3.729 4.156,3.938 0.208,0.208 10 false 3 4.469,2.688 5.083,3.083 0.615,0.396 10 false EFI MAIN NO. 2 4.333,4.01 5.573,4.25 1.24,0.24 10 false EFI NO. 3 6.198,6.25 6.656,6.448 0.458,0.198 10 false A62 6.188,6.417 6.646,6.615 0.458,0.198 10 false ECM 1.917,5.604 3.958,5.875 2.042,0.271 10 false *1: w/ Entry and Start System 1.927,5.979 4.063,6.24 2.135,0.26 10 false *2: w/o Entry and Start System 2.948,2.479 3.406,2.677 0.458,0.198 10 false IG2 4.396,1.906 4.854,2.104 0.458,0.198 10 false IGN 5.823,1.75 6.438,1.948 0.615,0.198 10 false IGSW 5.823,2.51 6.438,2.708 0.615,0.198 10 false BATT 5.813,3 6.427,3.198 0.615,0.198 10 false +B3 5.823,3.417 6.438,3.615 0.615,0.198 10 false +B2 5.823,3.823 6.438,4.021 0.615,0.198 10 false +B 5.823,4.198 6.438,4.396 0.615,0.198 10 false MREL 5.823,4.646 6.438,4.844 0.615,0.198 10 false E1 5.833,5.042 6.448,5.24 0.615,0.198 10 false E2 5.833,5.438 6.448,5.635 0.615,0.198 10 false E3 5.833,5.865 6.448,6.063 0.615,0.198 10 false E4 5.573,2.427 5.885,2.625 0.313,0.198 10 false 15 5.604,2.917 5.917,3.115 0.313,0.198 10 false 1 5.542,1.646 5.854,1.844 0.313,0.198 10 false 37 5.573,3.333 5.885,3.531 0.313,0.198 10 false 14 5.615,3.74 5.927,3.938 0.313,0.198 10 false 2 5.625,4.125 5.938,4.323 0.313,0.198 10 false 9 5.625,4.552 5.938,4.75 0.313,0.198 10 false 4 5.625,4.948 5.938,5.146 0.313,0.198 10 false 5 5.552,5.333 5.865,5.531 0.313,0.198 10 false 17 5.563,5.771 5.875,5.969 0.313,0.198 10 false 18 5.219,0.635 5.531,0.833 0.313,0.198 10 false 9 0.646,5.375 1.719,5.573 1.073,0.198 10 false Battery 0.51,4.625 1.583,4.823 1.073,0.198 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspection the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the tester display.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
A372442C02
0.313,0.104 0.625,0.302 0.313,0.198 10 false *1 2.469,4.427 2.781,4.625 0.313,0.198 10 false *2 2.865,2.052 3.177,2.25 0.313,0.198 10 false *3
*1 Engine Room Relay Block and Junction Block
*2 EFI MAIN NO. 1 Relay
*3 IG2 Relay


Remove the IG2 relay from the engine room relay block and junction block.


b.

Remove the EFI MAIN NO. 1 relay from the engine room relay block and junction block.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (IG2 relay holder) - Body ground Always 11 to 14 V
5 (EFI MAIN NO. 1 relay holder) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IG2 relay holder) - Body ground Always Below 1 Ω
2 (EFI MAIN NO. 1 relay holder) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT IG2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK - BATTERY)

2.INSPECT IG2 RELAY

Result:
Proceed to
OK
NG



OK

3.INSPECT EFI MAIN NO. 1 RELAY

NG

REPLACE IG2 RELAY

3.INSPECT EFI MAIN NO. 1 RELAY
a.

Inspect the EFI MAIN NO. 1 relay.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK - ECM)

NG

REPLACE EFI MAIN NO. 1 RELAY

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK - ECM)
a.

Disconnect the ECM connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-9 (MREL) - 1 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-2 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-14 (+B2) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-1 (+B3) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
A62-9 (MREL) or 1 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-2 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-14 (+B2) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
A62-1 (+B3) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-4 (E1) - Body ground Always Below 1 Ω
A62-5 (E2) - Body ground Always Below 1 Ω
A62-17 (E3) - Body ground Always Below 1 Ω
A62-18 (E4) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGSW TERMINAL VOLTAGE)
A355840C08
0.292,1.052 0.698,1.292 0.406,0.24 1.865,1.375 0.938,1.729 true 0.531,1.646 0.979,1.875 0.448,0.229 10 false IGSW 0.375,1.083 0.896,1.323 0.521,0.24 10 false A62 0.135,0.125 0.656,0.365 0.521,0.24 10 false *a
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A62-37 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (ECM - IG2 RELAY)
7.CHECK HARNESS AND CONNECTOR (ECM - IG2 RELAY)
a.

Disconnect the ECM connector.


b.

Remove the IG2 relay from the engine room No. 1 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-37 (IGSW) - 5 (IG2 relay holder) Always Below 1 Ω
A62-37 (IGSW) or 5 (IG2 relay holder) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK (w/ Entry and Start System) B
OK (w/o Entry and Start System) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 RELAY)

C

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IG2 RELAY)
8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the IG2 relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-9 (IG2D) - 1 (IG2 relay holder) Always Below 1 Ω
G82-9 (IG2D) or 1 (IG2 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IG2 RELAY)
a.

Disconnect the ignition switch assembly connector.


b.

Remove the IG2 relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-3 (IG2) - 1 (IG2 relay holder) Always Below 1 Ω
G4-3 (IG2) or 1 (IG2 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2WW STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY