Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM J

2WW ENGINE CONTROL  ECD SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground, which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A311437E04
0.146,0.938 2.375,1.167 2.229,0.229 10 false from Engine Stop and Start ECU*1 2.927,1.885 3.427,2.094 0.5,0.208 10 false G16 2.927,2.052 5.156,2.281 2.229,0.229 10 false Combination Meter Assembly 6.146,2.26 6.49,2.458 0.344,0.198 10 false A62 6.146,2.427 6.615,2.646 0.469,0.219 10 false ECM 5.969,0.948 6.313,1.146 0.344,0.198 10 false W 5.646,0.844 5.906,1.042 0.26,0.198 10 false 59 4.823,0.844 5.083,1.042 0.26,0.198 10 false 11 2.688,0.844 2.948,1.042 0.26,0.198 10 false 39 2.969,0.844 3.292,1.031 0.323,0.188 10 false IG+ 4.438,0.844 4.76,1.031 0.323,0.188 10 false CHK 3.958,1.135 4.281,1.323 0.323,0.188 10 false MIL 1.052,1.313 2.427,1.542 1.375,0.229 10 false from METER fuse*2 0.146,1.938 2.094,2.188 1.948,0.25 10 false *1: w/ Stop and Start System 0.167,2.323 2.167,2.583 2,0.26 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
Result Proceed to
MIL remains on A
MIL does not illuminate B




A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Check if DTCs have been stored. If DTCs are output, write them down.


d.

Clear the DTCs.


e.

Check that the MIL turns off.

OK:

MIL turns off.



Result:
Proceed to
OK
NG



OK

REPLACE CIRCUITS INDICATED BY OUTPUT DTCS

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
A355840C09
0.292,1.052 0.698,1.292 0.406,0.24 0.375,1.094 0.896,1.333 0.521,0.24 10 false A62 0.135,0.125 0.656,0.365 0.521,0.24 10 false *a
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-11 (CHK) or A62-59 (W) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-11 (CHK) - A62-59 (W) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR