When the engine stop and start ECU receives the OFF signal from the ignition or starter switch assembly*1 or certification ECU (smart key ECU assembly)*2 when communication with the ECM is normal, the engine stop and start ECU stores DTC P2531.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| P2531 | Ignition Switch Run Position Circuit Low | Both of the following conditions continue for 10 seconds or more (1 trip detection logic):
·
Ignition switch off signal is input. ·
Communication with the ECM is normal. |
·
Wire harness or connector ·
IG2 relay ·
EFI-MAIN NO. 1 relay ·
Ignition or starter switch assembly (w/o Entry and Start System) ·
Certification ECU (Smart key ECU assembly) (w/ Entry and Start System) ·
Engine stop and start ECU |
Does not come on | DTC stored |
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.
Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Keep the engine stopped by stop and start control for 1 second or more.
Depress the clutch pedal and start the engine.
If the engine cranks slowly when the engine is restarted, it can be determined that battery voltage is low.
Check that DTCs are not output.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR
STOP AND START SYSTEM OPERATION CHECK
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.
Start the engine and warm it up.
Turn the air conditioning system off.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Allow the engine to stop by stop and start control.
Depress the clutch pedal and start the engine.
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>FREEZE FRAME DATA
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Data List / IG Switch.
| Tester Display |
|---|
| IG Switch |
Read the value displayed on the GTS.
| Tester Display | Result | Proceed to |
|---|---|---|
| IG Switch | OFF | A |
| ON | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the G87 engine stop and start ECU connector.
Remove the IG2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G87-18 (IG2) - IG2 relay terminal 5 | Always | Below 1 Ω |
| G87-18 (IG2) - Body ground | Always | 10 kΩ or higher |
| IG2 relay terminal 5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the IG2 relay.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 relay terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG2 relay from the engine room relay block and junction block assembly.
w/ Entry and Start System:
Disconnect the G82 certification ECU (smart key ECU assembly) connector.
w/o Entry and Start System:
Disconnect the G4 ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 relay terminal 1 - G82-9 (IG2D) | Always | Below 1 Ω |
| IG2 relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| G82-9 (IG2D) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 relay terminal 1 - G4-3 (IG2) | Always | Below 1 Ω |
| IG2 relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| G4-3 (IG2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A66 engine stop and start ECU connector.
Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-1 (+B) - EFI-MAIN NO. 1 relay terminal 3 | Always | Below 1 Ω |
| A66-1 (+B) - Body ground | Always | 10 kΩ or higher |
| EFI-MAIN NO. 1 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-37 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the EFI-MAIN NO. 1 relay.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If communication between the GTS and vehicle is possible and SFI system data can be read 30 seconds after turning the ignition switch off a malfunction in the EFI-MAIN NO. 1 relay circuit is suspected.
Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.
Disconnect the A62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI-MAIN NO. 1 relay terminal 1 - A62-9 (MREL) | Always | Below 1 Ω |
| EFI-MAIN NO. 1 relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| A62-9 (MREL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK (w/ Entry and Start System) |
| OK (w/o Entry and Start System) |
| NG |
OK (w/ Entry and Start System)
OK (w/o Entry and Start System)
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-9 (IG2D) - Body ground | Ignition switch ACC | Below 1 V |
| G82-9 (IG2D) - Body ground | Ignition switch ON | 9 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>2WW STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG