As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed.
Therefore, always follow the instructions listed in the repair manual when performing this procedure.
for Manual Transaxle:
When the transaxle is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder assembly to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.
1.DISCHARGE FUEL SYSTEM PRESSURE
11212
2.REMOVE NO. 2 CYLINDER HEAD COVER
3. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
5.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL
6.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
51441
7.REMOVE NO. 1 ENGINE UNDER COVER
51443
8.REMOVE REAR ENGINE UNDER COVER RH
Remove the 3 clips and rear engine under cover RH.
51444
9.REMOVE REAR ENGINE UNDER COVER LH
Remove the 3 clips and rear engine under cover LH.
50819
10.REMOVE FRONT FLOOR COVER (w/ Cover)
11.REMOVE NO. 2 ENGINE UNDER COVER (w/ Cover)
Remove the bolt, clip and No. 2 engine under cover.
12.DRAIN ENGINE COOLANT
13.DRAIN ENGINE OIL
14.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
for 4WD/AWD
Click hereDrivetrain>EB61F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE OIL>REPLACEMENT
15.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)
for 2WD
Click hereDrivetrain>K111 MULTIDRIVE / CVT>FRONT DIFFERENTIAL OIL SEAL>REPLACEMENT
for 4WD/AWD
Click hereDrivetrain>K111F MULTIDRIVE / CVT>FRONT DIFFERENTIAL OIL SEAL(for LH Side)>REPLACEMENT
16.DRAIN TRANSFER OIL (for 4WD/AWD)
16470
17.REMOVE RADIATOR RESERVOIR ASSEMBLY
Slide the 2 clamps and disconnect the No. 1 and No. 2 water by-pass hoses from the radiator reservoir assembly.
Remove the 2 bolts and radiator reservoir assembly.
16361A
18.REMOVE V-RIBBED BELT
27020
19.REMOVE GENERATOR ASSEMBLY
for 100 A Type:
Click herePower Source / Network>3ZR-FE BATTERY / CHARGING>GENERATOR(for 100 A Type)>REMOVAL
for 130 A Type:
Click herePower Source / Network>3ZR-FE BATTERY / CHARGING>GENERATOR(for 130 A Type)>REMOVAL
16572D
20.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clamp and disconnect the No. 2 radiator hose from the water inlet.
88310
21.DISCONNECT COMPRESSOR WITH PULLEY ASSEMBLY
Disconnect the connector.
Remove the 2 bolts and 2 nuts.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts and disconnect the compressor with pulley assembly.
It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.
17705
22.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
23.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
74404A
24.REMOVE BATTERY CLAMP SUB-ASSEMBLY
28800
25.REMOVE BATTERY
74431
26.REMOVE BATTERY TRAY
16057
27.DISCONNECT RADIATOR HOSE SUB-ASSEMBLY
74411B
28.REMOVE FRONT BATTERY BRACKET
74414B
29.REMOVE BATTERY BRACKET REINFORCEMENT
89661
30.REMOVE ECM
16571
31.DISCONNECT NO. 1 RADIATOR HOSE
for CVT:
Disconnect the breather plug hose from the clamp.
Slide the clamp and disconnect the No. 1 radiator hose from the cylinder head.
23901
32.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 1 fuel pipe clamp, and then disconnect the fuel tube sub-assembly.
Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL SYSTEM>PRECAUTION
33.DISCONNECT WIRE HARNESS AND HOSE
Detach the 2 clamps and remove the bolt.
Disconnect the 2 connectors and remove the nut.
Detach the 2 claws and slide the wire harness, and then disconnect the wire harness.
Disconnect the terminal cap, and then remove the nut and disconnect the starter wire.
Detach the wire harness clamp.
for Manual Transaxle:
Detach the clamp, remove the bolt and disconnect the engine wire from the manual transaxle.
for CVT:
Detach the clamp, remove the bolt and disconnect the engine wire from the CVT.
Slide the clamp and disconnect the connector tube hose from the air tube.
Slide the 2 clamps and disconnect the heater water outlet hose and heater water inlet hose from the heater core.
33820B
34.DISCONNECT TRANSAXLE CONTROL CABLE ASSEMBLY (for Manual Transaxle)
Remove the 2 clips and disconnect the top ends of the transaxle control cable assembly from the transaxle.
Remove the 2 clips and disconnect the transaxle control cable assembly from the control cable bracket.
35.DISCONNECT TRANSAXLE CONTROL CABLE ASSEMBLY (for CVT)
Remove the nut and disconnect the transaxle control cable assembly from the control shaft lever.
Remove the clip and disconnect the transaxle control cable assembly from the control cable bracket.
Disconnect the transaxle control cable assembly from the control cable support.
Remove the bolt and disconnect the clamp of the control cable.
36.DISCONNECT CLUTCH HOSE (for Manual Transaxle)
Using a 10 mm union nut wrench, disconnect the clutch hose from the accumulator to flexible hose tube.
Remove the clip and disconnect the clutch hose.
45259A
37.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
38.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45025D
39.DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
43502H
40.REMOVE FRONT AXLE SHAFT NUT LH
43501H
41.REMOVE FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
42.DISCONNECT FRONT SPEED SENSOR LH
43.DISCONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
48810
44.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH
48820B
45.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
45047
46.DISCONNECT TIE ROD END SUB-ASSEMBLY LH
45046
47.DISCONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
48069
48.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
49.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
43420
50.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
for 4WD/AWD
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 4WD/AWD)>REMOVAL
43420G
51.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING
43410
52.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
for 4WD/AWD
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 4WD/AWD)>REMOVAL
17410
53.REMOVE FRONT EXHAUST PIPE ASSEMBLY
89465
54.DISCONNECT HEATED OXYGEN SENSOR (for 4WD/AWD)
37100
55.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)
32101A
56.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT)
for 4WD/AWD
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
51425B
57.REMOVE FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT (for 2WD)
Remove the 2 bolts and front lower engine mounting bracket reinforcement.
51218A
58.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH
Remove the 4 bolts and front suspension member reinforcement LH.
51217A
59.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH
Remove the 4 bolts and front suspension member reinforcement RH.
60.INSTALL ENGINE HANGER
Detach the fuel tube clamp.
Disconnect the air fuel ratio sensor connector and remove the bolt and air fuel ratio sensor bracket.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the 2 engine hangers with 2 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-37021 |
| No. 2 Engine Hanger | 12282-37011 |
| Bolt | 91552-81050 |
61.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Remove the 6 bolts and front crossmember sub-assembly.
| *A | for Manual Transaxle |
| *B | for CVT |
Remove the through bolt, nut and front engine mounting insulator.
While holding the nut in place, loosen the through bolt.
Set an engine lifter underneath the engine.
Place the engine on wooden blocks or equivalent so that the engine is level.
Remove the bolt and 2 nuts, and disconnect the engine mounting insulator RH.
| *A | for Manual Transaxle |
| *B | for CVT |
Remove the bolt and nut, and disconnect the engine mounting insulator LH.
Remove the 6 bolts and front suspension member brace rear RH and LH.
Remove the 2 bolts and front suspension crossmember sub-assembly.
Operate the engine lifter and slowly remove the engine from the vehicle.
Make sure that the engine is clear of all wiring and hoses.
While lowering the engine from the vehicle, do not allow it to contact the vehicle.
Attach an engine sling device and hang the engine with a chain block.
Remove the through bolt and front suspension crossmember from the engine with transaxle.
Do not damage any engine or transaxle components.
Raise the engine with transaxle assembly while keeping it level.
45319A
62.REMOVE STEERING GEAR HEAT INSULATOR (for RHD)
28100
63.REMOVE STARTER ASSEMBLY
for 1.0 kW
Click hereEngine / Hybrid System>3ZR-FE STARTING>STARTER(for 1.0 kW Type)>REMOVAL
for 1.3 kW
Click hereEngine / Hybrid System>3ZR-FE STARTING>STARTER(for 1.3 kW Type)>REMOVAL
11363A
64.REMOVE FLYWHEEL HOUSING SIDE COVER
36100
65.REMOVE TRANSFER ASSEMBLY (for 4WD/AWD)
30400
66.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)
for 4WD/AWD
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
30300
67.REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)
for 4WD/AWD
Click hereDrivetrain>EB61F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE ASSEMBLY>REMOVAL
68.FIX ENGINE ASSEMBLY
Using wooden blocks or plate lift attachments, set the engine on a flat surface.
Place wooden blocks or plate lift attachments so that the engine is level.
Never install attachments to the oil pan of the engine assembly or transaxle as doing so may deform the oil pan.
Perform this step while supporting the engine assembly using a sling device and chain block.
32101
69.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)
31210
70.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)
31250
71.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)
72.REMOVE CLUTCH TUBE (for Manual Transaxle)
31407B
73.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)
31400
74.REMOVE CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle)
13405
75.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
76.REMOVE ENGINE WIRE
Remove the engine wire from the engine.
77.INSTALL ENGINE TO ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Install the engine to an engine stand with the bolts.
Remove the 2 bolts and 2 engine hangers.
43457
78.REMOVE DRIVE SHAFT BEARING BRACKET
Remove the 3 bolts and drive shaft bearing bracket.
12371A
79.REMOVE REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
Remove the 2 bolts, 2 nuts and rear engine mounting insulator.
| *A | for 2WD | *B | for 4WD / AWD |
| *C | for Manual Transaxle | *D | for CVT |
12305
80.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator is necessary.
Remove the bolt and radiator reservoir bracket.
Remove the 3 bolts and engine mounting insulator sub-assembly RH.
12372A
81.REMOVE ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator is necessary.
Remove the bolt and wire harness clamp bracket.
Remove the 4 bolts and engine mounting insulator LH.