When the number of starter operations reaches the maximum number, the engine stop and start ECU stores DTC P1545 and blinks the stop and start cancel indicator light. When the STA signal detected by the ECM and by the engine stop and start ECU do not match, the engine stop and start ECU stores DTC P1545 and blinks the stop and start cancel indicator light.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| P1545 | Starter Maintenance | Both of the following conditions are met (1 trip detection logic):
·
Ignition switch ON ·
The number of starter operations reaches the specified limit. Both of the following conditions are met for 2 seconds or more (1 trip detection logic): ·
Normal communication with the ECM. ·
for CVT: The STA signal detected by the ECM and STA2 signal detected by the engine stop and start ECU do not match. ·
for Manual Transaxle: The STA signal detected by the ECM and the engine stop and start ECU do not match. |
·
Wire harness or connector ·
for CVT: ·
ST NO. 1 relay ·
ST NO. 2 relay ·
for Manual Transaxle: ·
ST NO. 1 relay ·
Engine stop and start ECU ·
Starter assembly ·
ECM |
Blinks | DTC stored |
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
for CVT:
Depress the brake pedal and stop the vehicle.
for Manual Transaxle:
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Keep the engine stopped by stop and start control for 1 second or more. (for CVT: Keep the shift lever in D.)
for CVT:
Release the brake pedal with the shift lever in D to start the engine.
for Manual Transaxle:
Depress the clutch pedal and start the engine.
If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.
Check that no DTCs are output.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
STOP AND START SYSTEM OPERATION CHECK
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.
Start the engine and warm it up.
Turn the air conditioning system off.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
for CVT:
Depress the brake pedal and stop the vehicle.
for Manual Transaxle:
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Allow the engine to stop by stop and start control. (for CVT: Keep the shift lever in D.)
for CVT:
Release the brake pedal with the shift lever in D to start the engine.
for Manual Transaxle:
Depress the clutch pedal and start the engine.
for CVT:
When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
for Manual Transaxle:
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
for CVT:
When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.
for Manual Transaxle:
When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Data List / Starter Operation #.
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| Starter Operation # |
| Result | Proceed to |
|---|---|
| 380000 or more
(Displays 1000000 or more)* |
A |
| Below 380000 | B |
*: If "Starter Operation #" displays 1000000 or more, it is necessary to replace the engine stop and start ECU as there is an internal malfunction in the ECU.
A
B
Replace the starter assembly
Click hereEngine / Hybrid System>3ZR-FAE STARTING>STARTER(w/ Stop And Start System)>REMOVAL
for CVT:
When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.
for Manual Transaxle:
When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.
If "Starter Operation #" displays 1000000 or more, the engine stop and start ECU must also be replaced.
Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL
Clear the number of starter operations by performing "Starter Exchange" using the GTS.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Enter the following menus: Powertrain / Stop and Start / Data List / Engine Starter Signal.
Read the values displayed on the GTS when the ignition switch is ON and the engine starts.
| Tester Display |
|---|
| Engine Starter Signal |
| Tester Display | Condition | Normal Condition |
|---|---|---|
| Engine Starter Signal | Ignition switch ON | OFF |
| Engine start | ON |
| Proceed to |
|---|
| OK |
| NG (for CVT) |
| NG (for Manual Transaxle) |
OK
NG (for CVT)
NG (for Manual Transaxle)
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the values displayed on the GTS when the ignition switch is ON and the engine starts.
| Tester Display |
|---|
| Starter Signal |
| Tester Display | Condition | Normal Condition |
|---|---|---|
| Starter Signal | Ignition switch ON | OFF |
| Engine start | ON |
| Proceed to |
|---|
| OK |
| NG (for CVT) |
| NG (for Manual Transaxle) |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG (for CVT)
NG (for Manual Transaxle)
Disconnect the A66 engine stop and start ECU connector.
Disconnect the A62 ECM connector.
Remove the ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-29 (STA) - ST NO. 2 relay terminal 2 | Always | Below 1 Ω |
| A62-29 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 2 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A66 engine stop and start ECU connector.
Disconnect the A62 ECM connector.
Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-29 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| A62-29 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A66 engine stop and start ECU connector.
Disconnect the A62 ECM connector.
Remove the ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-23 (STA2) - ST NO. 2 relay terminal 2 | Always | Below 1 Ω |
| A62-29 (STA) - ST NO. 2 relay terminal 2 | Always | Below 1 Ω |
| A66-23 (STA2) - A62-29 (STA) | Always | Below 1 Ω |
| A66-23 (STA2) - Body ground | Always | 10 kΩ or higher |
| A62-29 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 2 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST NO. 2 relay.
Click hereEngine / Hybrid System>3ZR-FAE STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 2 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A66 engine stop and start ECU connector.
Disconnect the A62 ECM connector.
Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-21 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| A62-29 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| A66-21 (STA) - A62-29 (STA) | Always | Below 1 Ω |
| A66-21 (STA) - Body ground | Always | 10 kΩ or higher |
| A62-29 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>3ZR-FAE STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG