When the steering pad switch assembly is used to select a control mode, a status change request signal is sent from the combination meter assembly to the engine stop and start ECU via CAN communication. Cooperative control is performed by the air conditioning amplifier assembly and engine stop and start ECU based on the selected control mode.
When stop and start priority control (Extended) is selected, the operation time of stop and start control will be extended in order to improve fuel economy.
for CVT:
When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
for Manual Transaxle:
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
When stop and start priority control (Extended) is selected, the operation of the air conditioning system is limited. If the customer reports that the cooling effectiveness of the air conditioning system is poor, check the selected control mode. If stop and start priority control (Extended) is selected, cancel the control mode and check if the cooling effectiveness of the air conditioning system improves. If it improves, explain to the customer that the operation of the air conditioning system was limited by stop and start control.
Depending on the vehicle conditions, the stop and start operation time may not change even if stop and start priority control (Extended) is selected.
Check the problem symptoms.
Check each symptom by checking the suspected areas in the table below.
By using the GTS and entering the following menus, the selected mode can be confirmed.
Powertrain / Stop and Start / Data List / Stop & Start A/C Mode
| Problem Symptoms | Trouble Area | Proceed to |
|---|---|---|
| Multi-information display screen does not change after pressing steering pad switch assembly | ·
Steering pad switch assembly ·
Spiral cable with sensor sub-assembly ·
Combination meter assembly ·
Engine stop and start ECU ·
Wire harness or connector (steering pad switch assembly - combination meter assembly) ·
Wire harness or connector (engine stop and start ECU - combination meter assembly) |
A |
| Multi-information display screen changes without pressing steering pad switch assembly | ·
Steering pad switch assembly ·
Spiral cable with sensor sub-assembly ·
Wire harness or connector (steering pad switch assembly - combination meter assembly) |
B |
| Multi-information display screen does not change but control mode changes | Combination meter assembly | C |
| Multi-information display screen changes but control mode does not change | ·
Air conditioning amplifier assembly ·
Wire harness or connector (engine stop and start ECU - air conditioning amplifier assembly) |
D |
| Control mode returns to default mode after turning ignition switch to ON | Engine stop and start ECU | E |
A
B
C
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
D
E
Using the steering pad switch assembly, check that all functions other than "Stop and Start A/c Mode" can be selected.
| Result | Proceed to |
|---|---|
| Only "Stop and Start A/C Mode" cannot be selected | A |
| No function can be selected using the steering pad switch assembly | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| CAN DTCs are output | B |
A
B
for LHD with Central Gateway ECU:
for RHD with Central Gateway ECU:
for LHD without Central Gateway ECU:
for RHD without Central Gateway ECU:
Turn the ignition switch off.
Disconnect the G8 spiral cable with sensor sub-assembly connector.
Disconnect the G16 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G8-10 (+DP) - G16-28 (STRG) | Always | Below 1 Ω |
| G8-10 (+DP) - Body ground | Always | 10 kΩ or higher |
| G16-28 (STRG) - Body ground | Always | 10 kΩ or higher |
| G8-11 (-DP) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spiral cable with sensor sub-assembly.
for Single Type:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>INSPECTION
for Dual Type:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Single Type:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>REMOVAL
for Dual Type:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>REMOVAL
Inspect the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Turn the ignition switch off.
Disconnect the G8 spiral cable with sensor sub-assembly connector.
Disconnect the G16 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G8-10 (+DP) - G16-28 (STRG) | Always | Below 1 Ω |
| G8-10 (+DP) - Body ground | Always | 10 kΩ or higher |
| G16-28 (STRG) - Body ground | Always | 10 kΩ or higher |
| G8-11 (-DP) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spiral cable with sensor sub-assembly.
for Single Type:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>INSPECTION
for Dual Type:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Single Type:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>REMOVAL
for Dual Type:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>REMOVAL
Inspect the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| CAN DTCs are output | B |
A
B
for LHD with Central Gateway ECU:
for RHD with Central Gateway ECU:
for LHD without Central Gateway ECU:
for RHD without Central Gateway ECU:
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B