Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. FRONT WHEELS FACING STRAIGHT AHEAD
2.REMOVE FRONT WHEELS
51441
3.REMOVE NO. 1 ENGINE UNDER COVER
for AD Series Engine: Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2AR and 3ZR-FE Engine: Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 3ZR-FAE Engine: Click hereEngine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2WW Engine: Click hereEngine / Hybrid System>2WW COOLING>RADIATOR>REMOVAL
50819
4.REMOVE FRONT FLOOR COVER
51443C
5.REMOVE REAR ENGINE UNDER COVER RH
for AD Series Engine: Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>DRIVE BELT>REMOVAL
for 2AR and 3ZR-FE Engine: Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 3ZR-FAE Engine: Click hereEngine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2WW Engine: Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>DRIVE BELT>REMOVAL
51442
6.REMOVE NO. 2 ENGINE UNDER COVER
51444A
7.REMOVE REAR ENGINE UNDER COVER LH
for AD Series Engine: Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2AR and 3ZR-FE Engine: Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 3ZR-FAE Engine: Click hereEngine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2WW Engine: Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
8.SECURE STEERING WHEEL
45259A
9.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
10.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45025D
11.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
48810
12.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH
| *a | Turn |
| *b | Hold |
Remove the nut and disconnect the front stabilizer link assembly LH from the front stabilizer bar.
If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.
48820B
13.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
45047
14.DISCONNECT TIE ROD END SUB-ASSEMBLY LH
45046
15.DISCONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
48069
16.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Remove the bolt and 2 nuts.
Disconnect the front lower No. 1 suspension arm from the lower ball joint.
48068
17.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
51218A
18.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH
Remove the 4 bolts and front suspension member reinforcement LH.
51217A
19.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH
Remove the 4 bolts and front suspension member reinforcement RH.
51425B
20.REMOVE ENGINE FRONT MOUNTING BRACKET REINFORCEMENT LOWER (for 2WW and 3ZR 2WD)
| *A | for 3ZR-FE (2WD) |
| *B | for 2WW Engine |
Remove the 2 bolts and engine front mounting bracket reinforcement lower.
52258B
21.REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH
Remove the 3 bolts and front suspension member rear brace LH.
52257A
22.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH
Use the same procedure described for the LH side.
51201
23.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Remove the 2 bolts and 2 nuts, and disconnect the front suspension crossmember sub-assembly from the rear engine mounting insulator.
| *a | Engine Lifter |
| *b | Attachment |
|
Attachment placement location |
Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.
Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.
Use the attachments to keep the front suspension crossmember sub-assembly level.
The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.
Remove the 2 bolts and front suspension crossmember sub-assembly.
Slowly lower the front suspension crossmember sub-assembly.
When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.
48069
24.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.