Home › Engine / Hybrid System › 2AD-FHV ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2014.10
RM3090E _51 Engine / Hybrid System _008404 2AD-FHV ENGINE MECHANICAL _0046933 ENGINE ASSEMBLY A

2AD-FHV ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.


PROCEDURE

Hide 1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

Hide 12611 6.REMOVE NO. 1 ENGINE COVER

A203808

a.

Detach the 4 clips and remove the No. 1 engine cover.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover to break.



Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

A295999

a.

Remove the 4 bolts and 2 screws.


b.

Remove the 10 clips and No. 1 engine under cover.


Hide 50819 8.REMOVE FRONT FLOOR COVER

Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

a.
A332570

Remove the bolt, clip and No. 2 engine under cover.


Hide 58165C 10.REMOVE FRONT FLOOR COVER RH

a.
A297530

Loosen the 3 nuts and remove the 3 clips and front floor cover RH.


Hide 51443 11.REMOVE REAR ENGINE UNDER COVER RH

Hide 51444 12.REMOVE REAR ENGINE UNDER COVER LH

A299169

a.

Remove the 2 clips and rear engine under cover LH.


Hide 52119A 17.REMOVE FRONT BUMPER COVER

Hide 17410 18.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 19.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 89480A 20.REMOVE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

Hide 74404A 21.REMOVE BATTERY CLAMP SUB-ASSEMBLY

A294113

a.

Remove the bolt and loosen the nut.


b.

Detach the 2 wire harness clamps.


c.

Detach the hook of the battery clamp sub-assembly from the front battery bracket, and then remove the battery clamp sub-assembly.


Hide 28899 22.REMOVE BATTERY INSULATOR

Hide 28800 23.REMOVE BATTERY

Hide 74431 24.REMOVE BATTERY TRAY

Hide 74411B 25.REMOVE FRONT BATTERY BRACKET

A294114

a.

Detach the 2 wire harness clamps.


b.

Remove the 4 bolts and front battery bracket.


Hide 74414B 26.REMOVE BATTERY BRACKET REINFORCEMENT

A294115

a.

Remove the 2 bolts and battery bracket reinforcement.


Hide 16400 27.REMOVE RADIATOR ASSEMBLY

Hide 25770A 28.DISCONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY

Hide 17705 30.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

a.

Disconnect the PCV hose.


b.

Loosen the hose clamp and disconnect the air cleaner hose.


c.
A294116

Disconnect the mass air flow meter connector and wire harness clamp.


d.

Detach the 3 clips and remove the air cleaner cap sub-assembly.


Hide 17801 31.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 32.REMOVE AIR CLEANER CASE

a.
A294117

Remove the 3 bolts and air cleaner case.


Hide 17769 33.REMOVE AIR CLEANER SUPPORT

a.
A294118

Remove the 2 nuts and air cleaner support.


Hide 34.REMOVE FUEL FILTER ASSEMBLY

a.
A294121

Slide the clip and disconnect the 2 fuel hoses.


b.

Remove the bolt and fuel filter assembly.


Hide 17119A 35.REMOVE AIR CLEANER BRACKET

a.
A294119

Disconnect the glow plug relay and level warning switch connector.


b.
A294120

Detach the 3 wire harness clamps.


c.
A294122

Disconnect the 2 fuel hoses from the air cleaner bracket.


d.

Remove the 3 bolts and air cleaner bracket.


Hide 37.DISCONNECT HOSES AND CONNECTORS

a.

Remove the engine room relay block and junction block cover.


b.
A294123

Disconnect the 3 connectors from the engine room No. 1 relay block.


c.
A294124

Remove the nut.


d.

Detach the 2 claws and disconnect the engine wire.


e.
A294126

Remove the bolt and disconnect the engine wire cover clamp and engine wire harness clamp.


f.

Remove the nut and disconnect the starter wire.


g.
A297513

Remove the bolt from the wire harness clamp bracket.


h.
A297511

Disconnect the transaxle ECM connector and detach the 2 wire harness clamps.


i.

Remove the bolt and disconnect the ground cable from the automatic transaxle.


j.
A297512

Detach the 2 clamps and disconnect the transaxle shift position switch connector.


k.
A294128

Detach the 3 wire harness clamps from the 3 wire harness brackets.


l.
A295884

Detach the 2 wire harness clamps and disconnect the 4 injector driver connectors.


m.
A295885

Remove the 2 nuts and injector driver assembly.


n.
A295887

Slide the clip and disconnect the vacuum pump hose from the vacuum pump assembly.


Hide 87245A 38.DISCONNECT INLET HEATER WATER HOSE

a.
A208836

Slide the clamp and disconnect the inlet heater water hose from the cylinder head sub-assembly.


Hide 87246A 39.DISCONNECT OUTLET HEATER WATER HOSE

a.

Slide the clamp and disconnect the outlet heater water hose from the No. 3 water by-pass pipe.


Hide 16057 40.DISCONNECT RADIATOR HOSE SUB-ASSEMBLY

A295889

a.

Slide the clamp and disconnect the radiator hose sub-assembly from the cylinder head sub-assembly.


Hide 17342F 41.REMOVE INTERCOOLER AIR HOSE

Hide 16264D 42.DISCONNECT NO. 2 WATER BY-PASS HOSE

a.
A295891

Slide the clamp and disconnect the No. 2 water by-pass hose from the No. 4 water by-pass pipe.


Hide 16572D 43.DISCONNECT NO. 2 RADIATOR HOSE

a.
A295890

Slide the clamp and disconnect the No. 2 radiator hose from the water inlet housing.


Hide 16470 44.REMOVE RADIATOR RESERVOIR ASSEMBLY

A295892

a.

Slide the clamp and disconnect the water by-pass hose from the radiator reservoir assembly.


b.

Remove the 2 bolts and radiator reservoir assembly.


Hide 88703 45.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.
A297510

Remove the bolt and disconnect the discharge hose sub-assembly.


b.

Remove the O-ring from the discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



c.

Disconnect the cooler compressor connector.


Hide 88704 46.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the bolt and disconnect the suction hose sub-assembly.


b.

Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 33820B 47.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
A208877

Remove the nut and clip, and disconnect the transmission control cable assembly from the transmission control cable bracket.


Hide 45259A 48.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 49.SECURE STEERING WHEEL

Hide 45260 50.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 51.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 43502H 52.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 53.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 54.DISCONNECT FRONT SPEED SENSOR LH

Hide 55.DISCONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 56.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 57.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 58.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 59.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 60.REMOVE FRONT AXLE ASSEMBLY LH

Hide 61.REMOVE FRONT AXLE ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51218A 64.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
A295896

Remove the 4 bolts and front suspension member reinforcement LH.


Hide 51217A 65.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

Hide 32101A 66.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 23292D 67.REMOVE FUEL HOSE PROTECTOR

a.
A210097

Remove the fuel hose protector from the cylinder head sub-assembly.


Hide 68.INSTALL ENGINE HANGER

a.
A297520C01
0.885,0.74 1.031,0.479 1.031,0.479 1.188,0.479 true 2.365,0.417 2.573,0.417 2.573,0.417 2.667,0.771 true 1.208,0.396 1.521,0.552 0.313,0.156 10 false *1 2.198,0.333 2.51,0.49 0.313,0.156 10 false *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the 2 engine hangers with the 2 bolts as shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
Part No.
No. 1 Engine Hanger 12281-26040
No. 2 Engine Hanger 12282-26010
Bolt 91552-81025 or 90105-W0042

·

Insert the claw of the No. 1 engine hanger into the hole of the cylinder head sub-assembly.

·

Fit the fork part of the No. 2 engine hanger onto the rib of the cylinder head sub-assembly.




Hide 69.REMOVE ENGINE WITH TRANSAXLE

a.
A295898

Remove the 6 bolts and disconnect the front crossmember sub-assembly.


b.
A295899

Remove the through bolt, nut and front engine mounting insulator.


c.

Set an engine lifter underneath the engine.

HINT:

Place the engine on wooden blocks or equivalent so that the engine is level.



d.
A295901

Remove the 2 bolts and 2 nuts and disconnect the engine mounting insulator sub-assembly RH.


e.
A295902

Remove the bolt and nut and disconnect the engine mounting insulator LH.


f.
A273397

Remove the 6 bolts, front suspension member rear brace RH and front suspension member rear brace LH.


g.

Remove the 2 bolts and front suspension member sub-assembly.


h.

Carefully remove the engine with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine from the vehicle, do not allow it to contact the vehicle.




i.

Attach an engine sling device and hang the engine with a chain block.


j.
A295903

Remove the through bolt and disconnect the rear engine mounting insulator.


Hide 17361J 70.REMOVE NO. 1 AIR TUBE

A273393

a.

Loosen the hose clamp, and remove the 2 bolts and No. 1 air tube.


Hide 28100 71.REMOVE STARTER ASSEMBLY

Hide 82121 72.REMOVE ENGINE WIRE

Hide 12311A 73.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
A212913

Remove the 4 bolts and front engine mounting bracket.


Hide 12321A 74.REMOVE REAR ENGINE MOUNTING BRACKET

a.
A224434

Remove the 4 bolts and rear engine mounting bracket.


Hide 12325A 75.REMOVE ENGINE MOUNTING BRACKET LH

HINT:

Perform this procedure only when replacement of the engine mounting bracket LH is necessary.


a.
A299459

Remove the 4 bolts and engine mounting bracket LH from the automatic transaxle assembly.


Hide 12156 76.REMOVE OIL PAN INSULATOR

a.
A202319

Remove the 2 bolts and oil pan insulator.


Hide 33118D 77.REMOVE STIFFENER PLATE RH

a.
A202320

Remove the 4 bolts and stiffener plate RH.


Hide 33119C 78.REMOVE STIFFENER PLATE LH

a.
A202321

Remove the 4 bolts and stiffener plate LH.


Hide 79.FIX ENGINE ASSEMBLY

a.

Using wooden blocks or plate lift attachments, set the engine on a flat surface.

NOTICE:
·

Place wooden blocks or plate lift attachments so that the engine is level.

·

Never install attachments to the oil pan of the engine assembly or transaxle as doing so may deform the oil pan.

·

Perform this step while supporting the engine assembly using a sling device and chain block.




Hide 32101 81.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A208894

Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly, and front drive plate spacer.


Hide 82.INSTALL ENGINE TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Install the engine to an engine stand, and remove the sling device and chain block from the engine.


b.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.


Hide 12371A 83.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A295905

Remove the 2 bolts, 2 nuts and rear engine mounting insulator.


Hide 12372A 84.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A299460

Remove the 4 bolts and engine mounting insulator LH from the body.


Hide 12305 85.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A300904

Remove the 3 bolts and engine mounting insulator sub-assembly RH from the body.