Home › Engine / Hybrid System › 2WW ENGINE MECHANICAL › ENGINE ASSEMBLY › 2015.10–2016.08
RM3090E _51 Engine / Hybrid System _044373 2WW ENGINE MECHANICAL _0211288 ENGINE ASSEMBLY A

2WW ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

As the engine assembly with transaxle assembly is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)

Hide 3. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

Hide 51441 6.REMOVE NO. 1 ENGINE UNDER COVER

Hide 52618 9.REMOVE FRONT LOWER BUMPER ABSORBER

Hide 12611 10.REMOVE NO. 1 ENGINE COVER

a.
A372600N01
1.021,1.146 1.177,1.344 0.156,0.198 10 true 2 2.042,1.448 2.198,1.646 0.156,0.198 10 true 1 2.51,0.938 2.667,1.135 0.156,0.198 10 true 3 1.656,0.656 1.813,0.854 0.156,0.198 10 true 4

Lift the No. 1 engine cover to detach the 4 clips in the sequence shown in the illustration and remove the No. 1 engine cover.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover to break.



Hide 50819 11.REMOVE FRONT FLOOR COVER

Hide 51442 12.REMOVE NO. 2 ENGINE UNDER COVER

a.
A332570

Remove the bolt, clip and No. 2 engine under cover.


Hide 58165C 13.REMOVE FRONT FLOOR COVER RH

a.
A297530

Loosen the 3 nuts and remove the 3 clips and front floor cover RH.


Hide 51443 14.REMOVE REAR ENGINE UNDER COVER RH

Hide 51444 15.REMOVE REAR ENGINE UNDER COVER LH

a.
A299169

Remove the 2 clips and rear engine under cover LH.


Hide 17410 18.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 74404A 19.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 28899 20.REMOVE BATTERY INSULATOR

Hide 28800 21.REMOVE BATTERY

Hide 74431 22.REMOVE BATTERY TRAY

Hide 74414B 24.REMOVE BATTERY BRACKET REINFORCEMENT

Hide 16400 25.REMOVE RADIATOR ASSEMBLY

Hide 88704 26.DISCONNECT SUCTION HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

Hide 88703 27.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

Hide 17880 28.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE ASSEMBLY

Hide 17701 29.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 16470 30.REMOVE RADIATOR RESERVOIR ASSEMBLY

a.
A372605

Slide the clamp and disconnect the water by-pass hose assembly from the radiator reservoir assembly.


b.

Slide the clamp and disconnect the No. 2 water by-pass hose assembly from the radiator reservoir assembly.


c.

Remove the 2 bolts and radiator reservoir assembly.


Hide 16261 31.REMOVE WATER BY-PASS HOSE ASSEMBLY

a.
A319847

Slide the clamp and disconnect the water by-pass hose assembly from the No. 1 air tube assembly.


b.
A318482

Remove the water by-pass hose assembly from the water by-pass pipe.


Hide 16057 32.REMOVE RADIATOR HOSE SUB-ASSEMBLY

a.
A319848

Slide the clamp and disconnect the radiator hose sub-assembly from the No. 1 air tube assembly.


b.
A319849

Remove the radiator hose sub-assembly from the water outlet.


Hide 33.DISCONNECT VACUUM HOSE

a.
A318485

Slide the clamp and disconnect the vacuum hose from the No. 2 vacuum hose assembly.


Hide 23273H 34.DISCONNECT NO. 2 FUEL HOSE

a.
A372606

Disconnect the No. 2 fuel hose from the fuel feed pipe sub-assembly.


Hide 23271H 35.DISCONNECT FUEL HOSE

a.

Disconnect the fuel hose from the fuel feed pipe sub-assembly.


Hide 36.DISCONNECT WATER HOSE SUB-ASSEMBLY

a.
A354306

Slide the clamp and disconnect the water hose sub-assembly from the No. 1 air tube assembly.


Hide 87246A 37.DISCONNECT OUTLET HEATER WATER HOSE

a.
A354307

Slide the clamp and disconnect the outlet heater water hose from the No. 1 air tube assembly.


Hide 38.DISCONNECT ENGINE WIRE

a.

Remove the No. 1 engine room relay block cover.


b.
A372603

Disconnect the 3 connectors.


c.
A372604

Remove the nut.


d.

Detach the 2 claws to disconnect the engine wire from the No. 1 engine room relay block.


e.
A318483

Remove the bolt to disconnect the ground cable.


Hide 23300 39.REMOVE FUEL FILTER ASSEMBLY

Hide 28610 40.REMOVE GLOW PLUG RELAY ASSEMBLY

a.

Disengage the glow plug relay assembly from the ECM bracket.


Hide 23921 41.REMOVE FUEL FILTER SUPPORT

a.
A372607

Raise the lever while pushing the lock on the lever, and disconnect the ECM connector.

NOTICE:

After disconnecting the ECM connector, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connector.



b.
A372608

Disconnect the connector.


c.

Detach the 4 clamps to disconnect the engine wire.


d.

Detach the clamp to disconnect the wire harness.


e.
A372609

Remove the 3 bolts and fuel filter support.


f.

Remove the nut and fuel filter support stay.


Hide 17771A 42.REMOVE AIR CLEANER BRACKET

a.
A372610

Remove the 3 bolts and air cleaner bracket.


Hide 33820B 43.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
A372611

Remove the 2 pins and disconnect the 2 transmission control cable assemblies from the manual transaxle assembly.


b.

Remove the 2 clips and disconnect the 2 transmission control cable assemblies from the transmission control cable bracket.


Hide 31470 44.DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

Hide 45259A 46.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 47.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 48.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 51425A 50.REMOVE FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT

Hide 51218A 51.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
A372613

Remove the 2 bolts and front suspension member reinforcement LH.


Hide 51217A 52.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.
A372612

Remove the 2 bolts and front suspension member reinforcement RH.


Hide 52258A 53.REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH

Hide 52257 54.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Perform the same procedure as for the LH side.


Hide 51201 55.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
A372623

Remove the 2 bolts and front suspension crossmember sub-assembly.


Hide 56.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set an engine lifter.

NOTICE:
·

Place height adjustment attachments and plate lift attachments under the engine assembly with transaxle.

·

Do not position the height adjustment attachments or plate lift attachments under the front crossmember sub-assembly.

·

Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.
A373932

Remove the 2 bolts to disconnect the front engine mounting insulator from the front crossmember sub-assembly.


c.
A372616

Remove the 4 bolts and front crossmember sub-assembly.


d.
A372598

Detach the 2 clamps and disconnect the air conditioner tube and accessory assembly.


e.

Detach the 2 clamps and disconnect the suction pipe sub-assembly.


f.
A372599

Remove the 4 bolts, 3 nuts and engine mounting insulator sub-assembly RH.


g.
A372614

Remove the bolt and nut to remove the engine mounting insulator LH.

HINT:

While holding the bolt in place, loosen the nut.



h.
A372615

Remove the bolt, nut and disconnect the front engine mounting insulator.

HINT:

When removing the bolt, keep the nut from rotating.



i.

Carefully remove the engine assembly with transaxle from the vehicle.

NOTICE:

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.



j.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 12371A 57.DISCONNECT REAR ENGINE MOUNTING INSULATOR

a.
A372617

Remove the bolt to disconnect the rear engine mounting insulator.


Hide 82121 58.REMOVE ENGINE WIRE

a.

Disconnect the connectors and detach the clamps securing the engine wire to the engine assembly, and then remove the bracket bolts and engine wire from the engine assembly.


Hide 17361J 59.REMOVE NO. 1 AIR TUBE ASSEMBLY

a.

Disconnect the compressor outlet elbow to the turbocharger sub-assembly.


b.
A339101

Disconnect the No. 4 water by-pass hose from the EGR cooler assembly.


c.

Remove the 2 bolts and disconnect the No. 1 air tube assembly from the manual transaxle assembly.


Hide 31121 60.REMOVE NO. 1 CLUTCH HOUSING COVER

Hide 28100 62.REMOVE STARTER ASSEMBLY

Hide 63.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
A372618

Remove the 4 bolts and front engine mounting bracket from the manual transaxle assembly.


Hide 64.REMOVE REAR ENGINE MOUNTING BRACKET

a.
A318505

Remove the 5 bolts and rear engine mounting bracket from the manual transaxle assembly.


Hide 65.REMOVE ENGINE MOUNTING BRACKET LH

a.
A372621

Remove the 4 bolts and engine mounting bracket LH from the manual transaxle assembly.


Hide 30300 66.REMOVE MANUAL TRANSAXLE ASSEMBLY

a.
C341143

Remove the 6 bolts and manual transaxle assembly from the engine assembly.


Hide 67.INSTALL ENGINE TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Install the engine assembly to an engine stand, and remove the sling device and chain block from the engine assembly.


Hide 12361A 68.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A372619

Remove the 2 bolts and front engine mounting insulator from the front crossmember sub-assembly.


Hide 12371A 69.REMOVE REAR ENGINE MOUNTING INSULATOR

a.
A372620

Remove the 2 bolts, 2 nuts and rear engine mounting insulator from the front suspension crossmember sub-assembly.


Hide 12372A 70.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A372622

Remove the 4 bolts and engine mounting insulator LH from the vehicle body.