Home › Engine / Hybrid System › 2WW FUEL › FUEL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044374 2WW FUEL _0221818 FUEL SYSTEM G

2WW FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump operation.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of FPC.

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of FPC
50004 371 12

iv.

Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the No. 1 integration relay, fuel suction tube with pump and gauge assembly, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the ignition switch off.


d.

Disconnect the GTS from the DLC3.


Hide 2.CHECK FUEL PRESSURE

a.

Measure the battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) terminal - Negative (-) terminal Ignition switch off 11 to 14 V



b.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Remove the No. 1 fuel filter protector.

Click hereEngine / Hybrid System>2WW FUEL>FUEL FILTER>REPLACEMENT


d.
A362569

Disconnect the No. 3 fuel hose from the fuel filter assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL SYSTEM>PRECAUTION


e.
A354347C01
0.906,0.5 1.021,0.5 1.021,0.5 1.229,0.823 false 1.604,1.302 1.74,1.302 1.74,1.302 1.854,1.125 false 2.021,0.635 2.281,0.635 false 2.26,1.156 2.521,0.823 2.521,0.823 2.656,0.823 false 0.615,1.781 0.875,1.781 false 1.177,2.146 1.177,2.354 false 2.719,2.625 2.844,2.344 2.844,2.344 2.979,2.344 false 0.927,3.021 1.083,3.021 1.083,3.021 1.292,3.219 false 0.844,4.073 0.844,3.854 false 0.365,4.135 0.365,3.958 false 0.729,0.427 1.042,0.583 0.313,0.156 10 false *1 2.333,0.552 2.646,0.708 0.313,0.156 10 false *a 1.417,1.219 1.729,1.375 0.313,0.156 10 false *b 0.927,1.698 1.24,1.854 0.313,0.156 10 false *c 1.104,2.375 1.417,2.531 0.313,0.156 10 false *d 3.031,2.26 3.344,2.417 0.313,0.156 10 false *e 0.781,4.104 0.979,4.323 0.198,0.219 10 false *f 0.292,4.146 0.5,4.385 0.208,0.24 10 false *g 2.708,0.74 3.021,0.896 0.313,0.156 10 false *a 0.76,2.927 1.073,3.083 0.313,0.156 10 false *a
*1 Fuel Tube Sub-assembly (Vehicle Side)
*a SST (Hose Band)
*b SST (T-joint)
*c SST (Gauge)
*d SST (Hose Joint)
*e SST (Hose)
*f SST (Fuel Tube Connector)
*g Fuel Pipe (Vehicle Side)


Install SST (EFI fuel pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)

NOTICE:
·

Do not use SST that has been used on gasoline vehicles.

·

Always use different SST for gasoline and diesel vehicles.




f.

Wipe up any spilled fuel.


g.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



h.

Connect the GTS to the DLC3.


i.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



j.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of FPC.

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of FPC
50004 371 12

k.

Measure the fuel pressure.

Standard Fuel Pressure:

450 to 700 kPa (4.6 to 7.1 kgf/cm2, 65 to 102 psi)


·

If the fuel pressure is more than the standard, check the fuel filter assembly.

·

If the fuel pressure is less than the standard value, check the fuel hoses, connections and fuel pump.



l.

Disconnect the GTS from the DLC3.


m.

Start the engine.


n.

Measure the fuel pressure at idle.

Standard Fuel Pressure:

450 to 700 kPa (4.6 to 7.1 kgf/cm2, 65 to 102 psi)



o.

Stop the engine.


p.

Connect the No. 3 fuel hose to the fuel filter assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL SYSTEM>PRECAUTION


q.

Install the No. 1 fuel filter protector.

Click hereEngine / Hybrid System>2WW FUEL>FUEL FILTER>REPLACEMENT



Hide 3.CHECK FUEL PRESSURE (for High Pressure)

a.

Read the Data List.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.



b.

Warm up the engine.


c.

Turn the ignition switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Common Rail Pressure and Common Rail Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Target Common Rail Pressure
Common Rail Pressure
50003 371 50,51

h.

Check that the internal fuel pressure of the common rail assembly is as specified.

OK:

Common Rail Pressure is within +/-10000 kPa of Target Common Rail Pressure when the engine is idling and running at 3000 rpm without load.



Hide 23990 4.CHECK PRESSURE DISCHARGE VALVE ASSEMBLY

a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Pressure Control Valve.

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Pressure Control Valve
50004 371 5
OK:
Condition Specified Condition
5% (Fuel Pressure Control valve OFF) Normal engine speed
95% (Fuel Pressure Control valve ON) The engine stops