Home › Engine / Hybrid System › 2WW FUEL › FUEL SUPPLY PUMP › from 2015.10
RM3090E _51 Engine / Hybrid System _044374 2WW FUEL _0221820 FUEL SUPPLY PUMP A

2WW FUEL  FUEL SUPPLY PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

SST A remains in the timing chain cover plate.

·

Always be sure to check the tightening torque.

·

If the pressure lines are leaking after installation, they must be replaced.

·

Do not overtighten the pressure lines.



PROCEDURE

Hide 22100 1.INSTALL FUEL SUPPLY PUMP ASSEMBLY

a.

Install the fuel quantity control valve with the 2 bolts.

HINT:

Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.



b.
A316278C01
2.823,1.531 2.583,1.531 2.583,1.531 2.344,1.281 true 2.885,1.448 3.198,1.604 0.313,0.156 10 false *1
*1 Injection Pump Drive Gear


To insert the fuel supply pump assembly shaft in the injection pump drive gear, it may be necessary to turn the fuel supply pump assembly several degrees so that the spline indicated by the arrow in the illustration and the groove in the fuel supply pump assembly shaft are aligned. Then rotate the fuel supply pump assembly back to the position where the screw can be installed.


c.

Install the fuel supply pump assembly to the cylinder block.

NOTICE:

Do not damage the shaft, especially the taper.


HINT:
A316279

When installing a new fuel supply pump assembly, adjust the fuel supply pump assembly and injection pump drive gear alignment by turning the fuel supply pump assembly 45° clockwise (top view).



d.
A316277N01
1.833,1.052 2.125,0.635 2.125,0.635 2.25,0.635 true 2.313,0.552 2.76,0.74 0.448,0.188 10 true SST A

Tighten the central bolt connection between the fuel supply pump assembly and injection pump drive gear.

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)


e.

Install the 2 bolts to the fuel supply pump assembly.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


f.
A316275N01
1.146,0.615 1.302,0.813 0.156,0.198 10 false 1 2.281,0.115 2.438,0.313 0.156,0.198 10 true 2 1.021,1.448 1.125,1.635 0.104,0.188 10 true 3 1.396,1.917 1.5,2.104 0.104,0.188 10 true 4

Temporarily install the fuel supply pump assembly support with the 4 bolts by hand in the order shown in the illustration.


g.
A316275N03
1.146,0.615 1.302,0.813 0.156,0.198 10 false 4 2.281,0.115 2.438,0.313 0.156,0.198 10 true 1 1.021,1.448 1.125,1.635 0.104,0.188 10 true 2 1.396,1.917 1.5,2.104 0.104,0.188 10 true 3

Tighten the 4 bolts in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


h.
A316274N01
1.229,0.417 1.375,0.417 1.375,0.417 1.573,0.76 true 1.229,1.802 1.375,1.802 1.375,1.802 1.646,1.292 true 0.76,0.344 1.208,0.542 0.448,0.198 10 true SST A 0.771,1.729 1.219,1.927 0.448,0.198 10 false SST B

Install SST B to SST A, and then remove both SST A and SST B.

SST:

PZ4TB-04967-25



i.

Apply a light coat of engine oil to a new O-ring, and install it to the sealing cap.


j.

Install the sealing cap to the timing chain cover plate.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


k.

Install 2 new clamps to the fuel feed line hose and fuel return line hose.


l.

Connect the fuel feed line hose and fuel return line hose to the fuel supply pump assembly and tighten the 2 clamps.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


m.

Connect the connector to the fuel quantity control valve.


n.

Release the No. 1 cylinder set to TDC/compression.


Hide 23292A 2.INSTALL NO. 1 AND NO. 2 FUEL HOSE PROTECTOR

a.
A362709

Install the No. 2 fuel hose protector to the fuel feed line hose and fuel return line hose as shown in the illustration.


b.

Install the No. 1 fuel hose protector to the No. 2 fuel hose protector.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


c.

Attach the clamp to connect the fuel temperature sensor connector.


Hide 3.INSTALL FUEL INLET PIPE SUB-ASSEMBLY