Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptoms Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

"Power Steering (EPS)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside power steering ECU assembly

·

Power steering ECU assembly CAN branch wire or connector

·

Power steering ECU assembly



WIRING DIAGRAM

C334650E01
0.177,2.135 2.281,2.427 2.104,0.292 10 false No. 7 CAN Junction Connector 5.198,1.167 5.51,1.365 0.313,0.198 10 false h1 5.208,1.75 5.521,1.948 0.313,0.198 10 false h1 5.208,2.75 5.521,2.948 0.313,0.198 10 false h2 5.208,3.583 5.521,3.781 0.313,0.198 10 false h1 5.219,5.125 5.531,5.323 0.313,0.198 10 false h2 5.625,1.177 6.24,1.375 0.615,0.198 10 false CANH 5.625,1.74 6.24,1.938 0.615,0.198 10 false CANL 5.677,2.781 6.292,2.979 0.615,0.198 10 false PIG 5.646,3.604 6.26,3.802 0.615,0.198 10 false IG 5.635,5.135 6.25,5.333 0.615,0.198 10 false PGND 5.25,0.896 5.406,1.094 0.156,0.198 10 false 4 5.24,1.469 5.396,1.667 0.156,0.198 10 false 8 1.75,1.021 1.906,1.219 0.156,0.198 10 false 2 1.729,1.625 2.042,1.823 0.313,0.198 10 false 13 0.167,2 0.781,2.198 0.615,0.198 10 false G189 5.219,2.5 5.375,2.698 0.156,0.198 10 false 1 5.229,3.292 5.385,3.49 0.156,0.198 10 false 1 5.229,4.823 5.385,5.021 0.156,0.198 10 false 2 4.135,2.563 4.594,2.76 0.458,0.198 10 false EPS 2.219,2.75 3.208,2.969 0.99,0.219 10 false from Battery 4.031,3.417 4.708,3.635 0.677,0.219 10 false EPS-IG 1.583,3.604 3.063,3.854 1.479,0.25 10 false from IG1 NO.1 Relay*1 0.875,4.281 3.167,4.563 2.292,0.281 10 false from Engine Stop and Start ECU*2 0.208,5.427 2.313,5.646 2.104,0.219 10 false *1: w/o Stop and Start System 0.229,5.906 2.333,6.125 2.104,0.219 10 false *2: w/ Stop and Start System 5,6.042 6.99,6.323 1.99,0.281 10 false Power Steering ECU Assembly 3.448,3.729 3.906,3.927 0.458,0.198 10 false *1 3.469,4.396 3.927,4.594 0.458,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 12 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)
a.
C268317C01
2.438,1.167 2.844,1.469 0.406,0.302 1.458,1.271 1.26,0.979 1.26,0.979 1.052,0.979 true 1.042,1.781 1.292,1.781 1.292,1.781 1.458,1.427 true 0.063,0.052 0.375,0.208 0.313,0.156 10 *a 2.552,1.24 2.865,1.396 0.313,0.156 10 h1 0.646,0.896 1.146,1.104 0.5,0.208 10 CANH 0.646,1.698 1.146,1.906 0.5,0.208 10 CANL
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the power steering ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h1-4 (CANH) - h1-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C280375C01
0.365,2.521 0.719,2.771 0.354,0.25 0.635,1.021 0.99,1.271 0.354,0.25 0.927,0.75 1.115,0.75 1.115,0.75 1.427,1.021 true 0.844,3.094 1.031,3.094 1.031,3.094 1.354,2.625 true 2.094,2.646 2.417,3.042 2.417,3.042 2.656,3.042 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.74,1.063 1.052,1.219 0.313,0.156 10 h1 0.469,2.573 0.781,2.729 0.313,0.156 10 h2 0.573,3 0.885,3.156 0.313,0.156 10 PIG 2.708,2.958 3.177,3.135 0.469,0.177 10 PGND 0.729,0.656 1.042,0.813 0.313,0.156 10 IG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the power steering ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
h1-1 (IG) - Body ground Ignition switch ON 11 to 14 V
h2-1 (PIG) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C280375C01
0.365,2.521 0.719,2.771 0.354,0.25 0.635,1.021 0.99,1.271 0.354,0.25 0.927,0.75 1.115,0.75 1.115,0.75 1.427,1.021 true 0.844,3.094 1.031,3.094 1.031,3.094 1.354,2.625 true 2.094,2.646 2.417,3.042 2.417,3.042 2.656,3.042 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.74,1.063 1.052,1.219 0.313,0.156 10 h1 0.469,2.573 0.781,2.729 0.313,0.156 10 h2 0.573,3 0.885,3.156 0.313,0.156 10 PIG 2.708,2.958 3.177,3.135 0.469,0.177 10 PGND 0.729,0.656 1.042,0.813 0.313,0.156 10 IG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the power steering ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
h1-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V
h2-1 (PIG) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (IG terminal) B
NG (Except IG terminals) C



A

REPLACE POWER STEERING ECU ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR