Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Driving Support ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Driving Support ECU Communication Stop Mode Either condition is met:
·

"Driving Support (Cruise Control-ACC)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Driving Support ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly CAN branch wire or connector

·

Driving support ECU assembly



WIRING DIAGRAM

C329326E11
1.552,0.885 2.042,1.354 0.49,0.469 10 false 3 1.531,1.385 2.021,1.854 0.49,0.469 10 false 13 0.271,1.927 0.76,2.396 0.49,0.469 10 false G174 0.271,2.104 2.25,2.396 1.979,0.292 10 false No. 9 CAN Junction Connector 5.365,0.875 5.854,1.344 0.49,0.469 10 false 10 5.365,1.406 5.854,1.875 0.49,0.469 10 false 11 3.948,2.302 4.948,2.635 1,0.333 10 false ECU-IG NO.2 5.417,2.323 5.906,2.792 0.49,0.469 10 false 7 5.656,2.448 6.146,2.917 0.49,0.469 10 false B 5.375,3.698 5.865,4.167 0.49,0.469 10 false 28 5.646,3.813 6.135,4.281 0.49,0.469 10 false GND 5.104,4.781 5.594,5.073 0.49,0.292 10 false G168 5.104,4.958 7.031,5.219 1.927,0.26 10 false Driving Support ECU Assembly 3.552,3.427 4.042,3.896 0.49,0.469 10 false *2 0.927,3.26 3.135,3.594 2.208,0.333 10 false from Engine Stop and Start ECU*2 1.656,2.458 3.365,2.813 1.708,0.354 10 false from IG1 NO.1 Relay*1 0.417,4.896 2.979,5.323 2.563,0.427 10 false *1: w/o Stop and Start System 3.51,2.594 4,3.063 0.49,0.469 10 false *1 0.417,5.229 2.76,5.604 2.344,0.375 10 false *2: w/ Stop and Start System 5.656,0.99 6.208,1.354 0.552,0.365 10 false CA2H 5.656,1.5 6.198,1.844 0.542,0.344 10 false CA2L

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (DRIVING SUPPORT ECU ASSEMBLY CAN BRANCH WIRE)
a.
C338465C08
1.375,0.302 1.917,0.552 0.542,0.25 2.479,1.115 2.802,0.729 2.802,0.729 2.948,0.729 true 2.375,1.115 2.677,0.417 2.677,0.417 2.823,0.417 true 0.188,0.135 0.5,0.292 0.313,0.156 10 false *a 1.469,0.313 1.969,0.604 0.5,0.292 10 false G168 2.875,0.302 3.313,0.448 0.438,0.146 10 false CA2H 2.99,0.625 3.427,0.771 0.438,0.146 10 false CA2L
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G168-10 (CA2H) - G168-11 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE DRIVING SUPPORT ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CA2H, CA2L)

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C338465C09
1.385,0.333 1.969,0.563 0.583,0.229 2.74,1.844 2.563,1.844 2.563,1.844 2.271,1.323 true 0.708,0.531 0.833,0.531 0.833,0.531 1.292,1.115 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.5,0.354 2.042,0.563 0.542,0.208 10 false G168 2.792,1.729 3.292,1.885 0.5,0.156 10 false GND 0.583,0.427 1.083,0.583 0.5,0.156 10 false B
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G168-7 (B) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G168-28 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C338465C09
1.385,0.333 1.969,0.563 0.583,0.229 2.74,1.844 2.563,1.844 2.563,1.844 2.271,1.323 true 0.708,0.531 0.833,0.531 0.833,0.531 1.292,1.115 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.5,0.354 2.042,0.563 0.542,0.208 10 false G168 2.792,1.729 3.292,1.885 0.5,0.156 10 false GND 0.583,0.427 1.083,0.583 0.5,0.156 10 false B
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G168-7 (B) - Body ground Ignition switch ON 10.5 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G168-28 (GND) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (B terminal) B
NG (GND terminal) C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR