Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM › from 2015.10
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0050373 BACK DOOR CLOSER SYSTEM C

DOOR / HATCH  BACK DOOR CLOSER SYSTEM  B2251  Back Door Closer Switch Malfunction  


DESCRIPTION

The multiplex network door ECU receives signals from the latch switch, sector switch, pawl switch and back door courtesy switch, which are built into the back door lock assembly. Based on these switch signals, the latch position of the back door lock assembly is determined.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2251 Back Door Closer Switch Malfunction While the back door closer is operating, a malfunction is detected in position information from the back door courtesy switch within a specified amount of time.
·

Back door lock assembly

·

Harness or connector

·

Multiplex network door ECU

·

Instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU)



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

·

Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Courtesy SW Back door courtesy switch signal ON or OFF ON: Back door open
OFF: Back door closed
*: Refer to "CONSTRUCTION AND OPERATION"

*: Refer to "CONSTRUCTION AND OPERATION"

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>SYSTEM DESCRIPTION

Body Electrical > Back Door > Data List
Tester Display
Courtesy SW
50003 159 4
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

2.INSPECT BACK DOOR LOCK ASSEMBLY
2.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL


b.

Inspect the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the U27 back door lock assembly connector.


b.

Disconnect the U29 multiplex network door ECU connector.


c.

Disconnect the 3E instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U27-4 (CTY) - U29-11 (FUL) Always Below 1 Ω
3E-33 - U29-11 (FUL) Always Below 1 Ω
U27-1 (E) - Body ground Always Below 1 Ω
U27-4 (CTY) or U29-11 (FUL) - Body ground Always 10 kΩ or higher
3E-33 or U29-11 (FUL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS
a.

Disconnect the U28 multiplex network door ECU connector.


b.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy switch signal ON or OFF ON: Back door open
OFF: Back door closed
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Courtesy SW
50003 123 26
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)