Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1403  Rear Speed Sensor RH Malfunction  C1404  Rear Speed Sensor LH Malfunction  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C121324C01
1.948,3.333 1.948,2.802 false 1.948,2.802 2.104,2.802 false 2,1.302 2.26,1.073 false 0.385,2.563 1.135,2.76 0.75,0.198 10 false *B 0.385,0.188 1.135,0.385 0.75,0.198 10 false *A 1.865,4.5 2.083,4.677 0.219,0.177 10 false *2 1.823,2.135 2.042,2.302 0.219,0.167 10 false *2 2.125,2.75 3.083,2.948 0.958,0.198 10 false *1 2.292,1 3.25,1.198 0.958,0.198 10 false *1 6.438,1.802 6.854,1.958 0.417,0.156 10 false 1.4 V 6.427,2.208 6.844,2.365 0.417,0.156 10 false 0.7 V 5.594,2.625 5.792,2.813 0.198,0.188 10 false *c 4.677,2.635 4.979,2.823 0.302,0.188 10 false *b 5.229,1.365 5.542,1.563 0.313,0.198 10 false *a
*A for 4WD/AWD *B for 2WD
*1 Speed Sensor *2 Speed Sensor Rotor
*a Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b Low speed
*c High speed - -


DTC No. Detection Item DTC Detection Condition Trouble Area
C1403 Rear Speed Sensor RH Malfunction Either of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more (for 2WD) or for 30 seconds or more (for4WD/AWD).

2.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed less than 10 km/h (6 mph), outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more (for 2WD) or for 30 seconds or more (for4WD/AWD). (except both rear speed sensors are 0 km/h)


·

Rear speed sensor RH (for 4WD/AWD)

·

Rear speed sensor RH (Rear axle hub and bearing assembly RH) (for 2WD)

·

Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH)

·

Wire harness or connector


C1404 Rear Speed Sensor LH Malfunction Either of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more (for 2WD) or for 30 seconds or more (for4WD/AWD).

2.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed less than 10 km/h (6 mph), outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more (for 2WD) or for 30 seconds or more (for4WD/AWD). (except both rear speed sensors are 0 km/h)


·

Rear speed sensor LH (for 4WD/AWD)

·

Rear speed sensor LH (Rear axle hub and bearing assembly LH) (for 2WD)

·

Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH)

·

Wire harness or connector



CAUTION / NOTICE / HINT

NOTICE:

Disassembly of the speed sensor from the rear axle hub and bearing assembly is prohibited (for 2WD).


PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C118693C01
0.676,0.188 0.859,0.363 0.183,0.176 10 *a 2.229,0.188 2.412,0.363 0.183,0.176 10 *b 1.738,1.666 1.923,1.836 0.185,0.17 10 *c
*a Normal
*b Abnormal
*c Clearance


for 2WD:

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.



c.
C168336C14
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Normal
*b Abnormal
*c Clearance


for 4WD/AWD:

Check the rear speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION

OK:

There is no clearance between the sensor and the rear axle carrier.

The installation bolt is tightened properly.



Result:
Proceed to
OK (for 2WD)
OK (for 4WD/AWD)
NG (for 2WD)
NG (for 4WD/AWD)



OK (for 2WD)

4.READ VALUE USING GTS (REAR SPEED SENSOR)

OK (for 4WD/AWD)

2.INSPECT REAR SPEED SENSOR TIP

NG (for 2WD)

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG (for 4WD/AWD)

2.INSPECT REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.


OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR AXLE HUB AND BEARING ASSEMBLY

NG

CLEAN OR REPLACE REAR SPEED SENSOR

3.INSPECT REAR AXLE HUB AND BEARING ASSEMBLY
a.

Remove the rear axle hub and bearing assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.


OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

·

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.



c.

Reinstall the rear speed sensor and rear axle hub and bearing assembly.

for the rear speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for 4WD/AWD)>INSTALLATION

for the rear axle hub and bearing assembly: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>INSTALLATION


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

CLEAN OR REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

4.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4
f.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

for 2WD:

The rear speed sensor and rear speed sensor rotor are incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.

·

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Proceed to
OK
NG (for 2WD)
NG (for 4WD/AWD)



OK

NG (for 2WD)

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG (for 4WD/AWD)

5.REPLACE REAR SPEED SENSOR
5.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.



NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTCs C1403 and C1404 are not output
DTCs C1403 and/or C1404 are output


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

·

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.





DTCs C1403 and C1404 are not output

END

DTCs C1403 and/or C1404 are output

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY