Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.10–2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

for Segment Display Type:

Pressing the VSC OFF switch (telltale light assembly) turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, the TRC/TRAC OFF indicator light will come on.

If VSC and traction control turns OFF, the TRC/TRAC OFF indicator and VSC OFF indicator light will come on.

The VSC OFF indicator light is illuminated when the VSC and TRC/TRAC controls are prohibited by operating the VSC OFF switch (telltale light assembly).

By pressing the VSC OFF switch (telltale light assembly) for 3 seconds or more, the VSC OFF mode is activated, the VSC and TRC/TRAC controls are prohibited, and both the VSC OFF indicator light and the TRC/TRAC OFF indicator light in the combination meter are illuminated.

for TFT Display Type:

Pressing the VSC OFF switch (telltale light assembly) turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, TRC OFF is displayed on the multi-information display.

If VSC and traction control turns OFF, TRC OFF is displayed on the multi-information display and the VSC OFF indicator light will come on.

The VSC OFF indicator light is illuminated when the VSC and TRC controls are prohibited by operating the VSC OFF switch (telltale light assembly).

By pressing the VSC OFF switch (telltale light assembly) for 3 seconds or more, the VSC OFF mode is activated, VSC and TRC controls are prohibited, the VSC OFF indicator light illuminates and TRC OFF is displayed on the multi-information display.

WIRING DIAGRAM

C342523E02
5.969,2.177 6.427,2.375 0.458,0.198 10 false CSW 4.906,2.01 5.063,2.208 0.156,0.198 10 false 6 4.656,2.177 4.813,2.375 0.156,0.198 10 false + 3.708,2.146 4.167,2.344 0.458,0.198 10 false E 3.438,1.99 3.594,2.188 0.156,0.198 10 false 3 3.104,2.49 3.563,2.688 0.458,0.198 10 false G43 3.115,2.708 5.729,3.198 2.615,0.49 10 false VSC OFF Switch (Telltale Light Assembly) 5.406,3.469 7.01,3.896 1.604,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 5.417,3.25 5.875,3.448 0.458,0.198 10 false A80 5.698,2.021 6.156,2.219 0.458,0.198 10 false 33 0.135,3.458 2.135,3.802 2,0.344 10 false Combination Meter Assembly 0.125,3.302 0.583,3.5 0.458,0.198 10 false G16 0.75,4.365 2.656,4.698 1.906,0.333 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD with Central Gateway ECU)
DTC is output (for RHD with Central Gateway ECU)
DTC is output (for LHD without Central Gateway ECU)
DTC is output (for RHD without Central Gateway ECU)



DTC is not output

3.INSPECT BATTERY

DTC is output (for LHD with Central Gateway ECU)

DTC is output (for RHD with Central Gateway ECU)

DTC is output (for LHD without Central Gateway ECU)

DTC is output (for RHD without Central Gateway ECU)

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)
NG (for 2WW)




OK

4.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)

NG (for 2AD-FHV)

NG (for 2AD-FTV)

NG (for 2AR-FE)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

NG (for 2WW)

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY

4.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A80 skid control ECU (brake actuator assembly) connector.


c.
C342353C31
1.49,0.104 1.865,0.375 0.375,0.271 1.656,1.875 1.656,1.75 1.656,1.75 1.896,1.323 true 1.563,0.156 2.021,0.354 0.458,0.198 10 false A80 1.479,1.906 1.917,2.094 0.438,0.188 10 false CSW 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A80-33 (CSW) - Body ground VSC OFF switch (telltale light assembly) held on Below 1 Ω
VSC OFF switch (telltale light assembly) off (Not pressed) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

6.INSPECT TELLTALE LIGHT ASSEMBLY
5.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Reconnect the A80 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/TRAC/VSC off mode Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC/TRAC off mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

g.

Check that the mode display changes according to the VSC OFF switch (telltale light assembly) operation.

OK:

Display changes according to the switch operation.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT TELLTALE LIGHT ASSEMBLY
a.

Remove the VSC OFF switch (telltale light assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL


b.

Inspect the VSC OFF switch (telltale light assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TELLTALE LIGHT ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TELLTALE LIGHT ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-33 (CSW) - G43-6 (+) Always Below 1 Ω
G43-13 (E) - Body ground Always Below 1 Ω
A80-33 (CSW) or G43-6 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR