Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.10–2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Indicator Light does not Come ON  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD with Central Gateway ECU)
DTC is output (for RHD with Central Gateway ECU)
DTC is output (for LHD without Central Gateway ECU)
DTC is output (for RHD without Central Gateway ECU)



DTC is not output

2.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)

DTC is output (for LHD with Central Gateway ECU)

DTC is output (for RHD with Central Gateway ECU)

DTC is output (for LHD without Central Gateway ECU)

DTC is output (for RHD without Central Gateway ECU)

2.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A80 skid control ECU (brake actuator assembly) connector.


c.
C342353C31
1.49,0.104 1.865,0.375 0.375,0.271 1.656,1.875 1.656,1.75 1.656,1.75 1.896,1.323 true 1.563,0.156 2.021,0.354 0.458,0.198 10 false A80 1.479,1.906 1.917,2.094 0.438,0.188 10 false CSW 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A80-33 (CSW) - Body ground VSC OFF switch (telltale light assembly) held on Below 1 Ω
VSC OFF switch (telltale light assembly) off (Not pressed) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

5.INSPECT TELLTALE LIGHT ASSEMBLY
3.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Reconnect the A80 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/TRAC/VSC off mode Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC/TRAC off mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

g.

Check that the mode display changes according to the VSC OFF switch (telltale light assembly) operation.

OK:

Display changes according to the switch operation.



Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

4.INSPECT COMBINATION METER ASSEMBLY
a.

Perform Active Test of the combination meter assembly using the GTS.


Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 94
b.

Check the combination meter assembly.

OK:

The VSC OFF indicator light turns on or off in accordance with the GTS.



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT TELLTALE LIGHT ASSEMBLY
a.

Remove the VSC OFF switch (telltale light assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL


b.

Inspect the VSC OFF switch (telltale light assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TELLTALE LIGHT ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TELLTALE LIGHT ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-33 (CSW) - G43-6 (+) Always Below 1 Ω
G43-13 (E) - Body ground Always Below 1 Ω
A80-33 (CSW) or G43-6 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR