Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › from 2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0141  Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  


DESCRIPTION

Refer to DTC P0136.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P0136

HINT:
·

Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located far from the engine assembly.

·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.

A290312E01
0.125,0.083 2.75,0.25 2.625,0.167 10 Reference (System Diagram of Sensor 2): 5,1 5.615,1.198 0.615,0.198 10 HT1B 5,1.552 5.615,1.75 0.615,0.198 10 OX1B 5,2.083 5.615,2.281 0.615,0.198 10 EX1B 3.344,2.052 4.844,2.25 1.5,0.198 10 Heated Oxygen Sensor 4.469,1.552 5.083,1.75 0.615,0.198 10 OX1B 4.469,1 5.083,1.198 0.615,0.198 10 HT1B 3.771,0.979 4.385,1.177 0.615,0.198 10 Heater 3.76,1.469 4.375,1.667 0.615,0.198 10 Sensor 3.333,1.552 3.583,1.75 0.25,0.198 10 E2 3.333,1 3.583,1.167 0.25,0.167 10 +B 1.063,2.208 1.76,2.375 0.698,0.167 10 EFI NO. 2 0.063,2.052 0.979,2.417 0.917,0.365 10 from EFI-MAIN NO. 1 Relay 0.167,1.135 1,1.333 0.833,0.198 10 from Battery 1.104,1.313 1.802,1.646 0.698,0.333 10 EFI-MAIN NO. 2 5.688,3.302 6.104,3.5 0.417,0.198 10 ECM 1.802,2.385 2.5,2.719 0.698,0.333 10 EFI-MAIN NO. 2



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

EFI-MAIN NO. 2 relay

·

ECM


Comes on DTC stored
P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) Heated oxygen sensor heater current reaches high limit
(Hybrid IC high current limiter monitor input "Fail") (1 trip detection logic).
·

Short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

EFI-MAIN NO. 2 relay

·

ECM


Comes on DTC stored
P0141 Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2) The cumulative heater resistance correction value exceeds the threshold (2 trip detection logic).
·

Open or short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

EFI-MAIN NO. 2 relay

·

ECM


Comes on DTC stored
P102D O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM Comes on DTC stored

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check (P0037, P0038 and P102D):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.



Heated Oxygen Sensor Heater Performance (P0141):

After the accumulated heater on time exceeds 100 seconds, the ECM calculates the heater resistance using battery voltage and the current applied to the heater. If the resistance is above the threshold value, the ECM determines that there is a malfunction in the heated oxygen sensor heater and stores DTC P0141.



MONITOR STRATEGY

Frequency of Operation Continuous: P0037, P0038, P102D
Once per driving cycle: P0141

TYPICAL ENABLING CONDITIONS

P0037
Time after heater on 10 seconds or more

P0038
Time after heater on 10 seconds or more

P0141
Battery voltage 10.5 V or higher
Time after fuel cut on to off 30 seconds or more
Accumulated heater on time 100 seconds or more
Duration that heated oxygen sensor impedance is less than 15 kΩ 2 seconds or more

P102D
Time after heater on 10 seconds or more

HINT:

When the value for the Data List item O2 Heater Curr Val B1S2 is not 0 A, the heater is on.


CONFIRMATION DRIVING PATTERN

A321021E01
0.76,0.99 1.469,1.198 0.708,0.208 10 false 3000 rpm 1.042,1.771 1.479,1.979 0.438,0.208 10 false ldling 0.49,2 1.396,2.385 0.906,0.385 10 false Engine Switch on (IG) 1.896,2.146 2.229,2.396 0.333,0.25 10 false [A] 2.74,1.667 3.073,1.917 0.333,0.25 10 false [B] 4.031,0.906 4.365,1.156 0.333,0.25 10 false [C] 5.281,1.656 5.615,1.906 0.333,0.25 10 false [D] 2.333,2.573 3.51,2.813 1.177,0.24 10 false 5 minutes or more 3.865,2.583 4.604,2.802 0.74,0.219 10 false 1 minute 4.813,2.583 5.99,2.823 1.177,0.24 10 false 5 minutes or more 5.948,3.031 6.281,3.281 0.333,0.25 10 false [E]

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0037, P0038, P0141 or P102D.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

A299798E01
5.417,0.573 5.719,0.74 0.302,0.167 10 false B77 5.417,1.344 5.719,1.51 0.302,0.167 10 false B77 5.417,2.021 5.719,2.188 0.302,0.167 10 false B77 5.417,3.031 5.719,3.198 0.302,0.167 10 false A62 5.469,0.396 5.719,0.563 0.25,0.167 10 false 24 5.75,0.479 6.167,0.646 0.417,0.167 10 false HT1B 5.427,1.177 5.729,1.344 0.302,0.167 10 false 100 5.75,1.25 6.135,1.417 0.385,0.167 10 false OX1B 5.417,1.854 5.719,2.021 0.302,0.167 10 false 132 5.75,2.01 6.167,2.177 0.417,0.167 10 false EX1B 5.458,2.865 5.708,3.031 0.25,0.167 10 false 46 5.75,3.01 6.167,3.177 0.417,0.167 10 false MREL 6.167,4 6.5,4.167 0.333,0.167 10 false ECM 3.417,1.5 3.719,1.667 0.302,0.167 10 false B25 3.417,1.667 4.917,1.917 1.5,0.25 10 false Heated Oxygen Sensor 3.781,1.188 4,1.354 0.219,0.167 10 false E2 4.188,1.177 4.604,1.344 0.417,0.167 10 false OX1B 4.698,1.25 5,1.417 0.302,0.167 10 false 3 3.563,1.25 3.729,1.417 0.167,0.167 10 false 4 3.563,0.479 3.729,0.646 0.167,0.167 10 false 2 3.771,0.479 3.99,0.646 0.219,0.167 10 false +B 4.198,0.469 4.615,0.635 0.417,0.167 10 false HT1B 4.698,0.479 5,0.646 0.302,0.167 10 false 1 2.583,0.469 2.75,0.635 0.167,0.167 10 false 3 1.76,0.469 1.896,0.635 0.135,0.167 10 false 5 1.75,0.75 1.885,0.917 0.135,0.167 10 false 1 2.583,0.74 2.719,0.906 0.135,0.167 10 false 2 1.698,1.177 2.75,1.344 1.052,0.167 10 false EFI-MAIN NO. 2 1.729,1.677 2.448,1.844 0.719,0.167 10 false EFI NO. 2 1.781,3.365 2.833,3.531 1.052,0.167 10 false EFI-MAIN NO. 1 2.531,2.656 2.667,2.823 0.135,0.167 10 false 3 2.531,2.948 2.667,3.115 0.135,0.167 10 false 1 1.792,2.948 1.927,3.115 0.135,0.167 10 false 2 1.792,2.656 1.958,2.823 0.167,0.167 10 false 5 0.604,3.219 1.188,3.385 0.583,0.167 10 false FL MAIN 0.75,3.958 1.25,4.208 0.5,0.25 10 false Battery 0.583,0.698 1.667,0.865 1.083,0.167 10 false EFI-MAIN NO. 2 0.583,2.875 1.583,3.042 1,0.167 10 false EFI-MAIN NO. 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Refer to "Data List / Active Test" [O2 Heater B1S2 and O2 Heater Curr Val B1S2].

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DATA LIST / ACTIVE TEST

·

When the values for the Data List item O2 Heater Curr Val B1S2 is not 0 A, the heater is on.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage (Click here Engine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
a.
A149595C01
0.5,1.833 0.917,2.083 0.417,0.25 1.948,1.833 2.365,1.417 false 0.083,0.083 0.344,0.281 0.26,0.198 10 *a 0.604,1.875 0.917,2.083 0.313,0.208 10 B25 2.417,1.333 2.667,1.5 0.25,0.167 10 +B
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


Disconnect the heated oxygen sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B25-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.INSPECT EFI-MAIN NO. 2 RELAY
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B25-1 (HT1B) - B77-24 (HT1B) Always Below 1 Ω
B25-1 (HT1B) or B77-24 (HT1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0141 OR P102D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0141 OR P102D)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P0037, P0038, P0141 or P102D is output B




A

B

5.INSPECT EFI-MAIN NO. 2 RELAY
a.

Inspect the EFI-MAIN No. 2 relay.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - HEATED OXYGEN SENSOR, EFI-MAIN NO. 1 RELAY)

NG

REPLACE EFI-MAIN NO. 2 RELAY

6.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - HEATED OXYGEN SENSOR, EFI-MAIN NO. 1 RELAY)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


c.

Disconnect the heated oxygen sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI-MAIN NO. 2 relay terminal 3 - B25-2 (+B) Always Below 1 Ω
EFI-MAIN NO. 2 relay terminal 1 - EFI-MAIN NO. 1 relay terminal 3 Always Below 1 Ω
EFI-MAIN NO. 2 relay terminal 2 - Body ground Always Below 1 Ω
EFI-MAIN NO. 2 relay terminal 3 or B25-2 (+B) - Body ground Always 10 kΩ or higher
EFI-MAIN NO. 2 relay terminal 1 or EFI-MAIN NO. 1 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)