The camshaft position sensor for the exhaust camshaft (EV1 signal) consists of a magnet and MRE (Magneto Resistance Element).
The exhaust camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0365 | Camshaft Position Sensor "B" Circuit (Bank 1) | No exhaust camshaft position sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic). | ·
Open or short in camshaft position sensor circuit (for exhaust camshaft) ·
Camshaft position sensor (for exhaust camshaft) ·
Exhaust camshaft ·
Valve timing ·
ECM |
Comes on | DTC stored |
| P0367 | Camshaft Position Sensor "B" Circuit Low Input (Bank 1) | The output voltage of the exhaust camshaft position sensor is less than 0.3 V for 4 seconds (1 trip detection logic). | ·
Open or short in camshaft position sensor circuit (for exhaust camshaft) ·
Camshaft position sensor (for exhaust camshaft) ·
ECM |
Comes on | DTC stored |
| P0368 | Camshaft Position Sensor "B" Circuit High Input (Bank 1) | The output voltage of the exhaust camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic). | ·
Open or short in camshaft position sensor circuit (for exhaust camshaft) ·
Camshaft position sensor (for exhaust camshaft) ·
ECM |
Comes on | DTC stored |
Reference: Inspection using an oscilloscope.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P0340
If no pulse signal is transmitted by the camshaft position sensor for exhaust camshaft despite the camshaft revolving, or the rotation of the exhaust camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds or more, the ECM stores a DTC.
| Required Sensors/Components (Main) | Exhaust camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
Start the engine and run it at idle for 10 seconds or more.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
| *a | Front view of wire harness connector
(to Camshaft Position Sensor for Exhaust Camshaft) |
Disconnect the camshaft position sensor for exhaust camshaft connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B41-3 (VC2) - Body ground | Engine switch on (IG) | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor for exhaust camshaft connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B41-1 (VVE+) - B77-81 (EV1+) | Always | Below 1 Ω |
| B41-2 (VVE-) - B77-112 (EV1-) | Always | Below 1 Ω |
| B41-1 (VVE+) or B77-81 (EV1+) - Body ground | Always | 10 kΩ or higher |
| B41-2 (VVE-) or B77-112 (EV1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the camshaft position sensor for exhaust camshaft installation.
Camshaft position sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the timing rotor of the exhaust camshaft.
Camshaft timing rotor does not have any cracks or deformation.
Perform "Inspection After Repair" after replacing the exhaust camshaft.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>P0011
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the camshaft position sensor (for exhaust camshaft).
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0365, P0367 or P0368 is output | A |
| DTC is not output | B |
If the engine does not start, replace the ECM.
A
B
Disconnect the camshaft position sensor for exhaust camshaft connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B41-3 (VC2) - B77-111 (VCE1) | Always | Below 1 Ω |
| B41-3 (VC2) or B77-111 (VCE1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG