Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Parking Assist ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Parking Assist ECU Communication Stop Mode Either condition is met:
·

"Parking Assist Monitor System" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Parking Assist ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of parking assist ECU

·

Parking assist ECU CAN branch wire or connector

·

Parking assist ECU



WIRING DIAGRAM

C329327E05
1.531,1.396 1.969,1.75 0.438,0.354 10 false 11 1.542,0.885 1.979,1.344 0.438,0.458 10 false 1 0.229,1.896 0.667,2.354 0.438,0.458 10 false N36 0.229,2.063 2.781,2.438 2.552,0.375 10 false No. 10 CAN Junction Connector 5.354,0.854 5.792,1.313 0.438,0.458 10 false 12 5.365,1.396 5.802,1.854 0.438,0.458 10 false 13 5.719,1 6.156,1.458 0.438,0.458 10 false CANH 5.708,1.5 6.146,1.958 0.438,0.458 10 false CANL 5.646,2.354 6.083,2.813 0.438,0.458 10 false +B 5.656,3.615 6.094,4.073 0.438,0.458 10 false ACC 5.667,4.833 6.104,5.292 0.438,0.458 10 false IG 5.656,5.792 6.094,6.25 0.438,0.458 10 false GND1 5.333,6.219 5.885,6.615 0.552,0.396 10 false a2 5.333,6.385 6.865,6.635 1.531,0.25 10 false Parking Assist ECU 5.417,2.25 5.854,2.708 0.438,0.458 10 false 2 5.417,3.51 5.854,3.969 0.438,0.458 10 false 1 5.427,4.708 5.865,5.167 0.438,0.458 10 false 6 5.417,5.677 5.854,6.135 0.438,0.458 10 false 3 4.188,3.479 4.719,3.906 0.531,0.427 10 false ACC 3.958,2.208 4.938,2.583 0.979,0.375 10 false ECU-B NO.1 3.458,2.5 3.896,2.958 0.438,0.458 10 false *1 3.469,3.177 3.906,3.635 0.438,0.458 10 false *2 3.948,4.688 4.885,4.99 0.938,0.302 10 false ECU-IG NO.2 2.177,2.375 3.604,2.729 1.427,0.354 10 false from Battery*1 0.958,3.021 3.281,3.365 2.323,0.344 10 false from Engine Stop and Start ECU*2 1.927,3.625 3.208,3.979 1.281,0.354 10 false from ACC Relay*1 1.604,4.854 3.073,5.177 1.469,0.323 10 false from IG1 NO.1 Relay*1 0.313,5.99 3.115,6.365 2.802,0.375 10 false *1: w/o Stop and Start System 0.313,6.292 3.208,6.604 2.896,0.313 10 false *2: w/ Stop and Start System 0.969,4.281 3.292,4.625 2.323,0.344 10 false from Engine Stop and Start ECU*2 0.948,5.479 3.281,5.833 2.333,0.354 10 false from Engine Stop and Start ECU*2 3.469,3.74 3.906,4.198 0.438,0.458 10 false *1 3.49,4.417 3.927,4.875 0.438,0.458 10 false *2 3.479,4.979 3.917,5.438 0.438,0.458 10 false *1 3.5,5.646 3.938,6.104 0.438,0.458 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (PARKING ASSIST ECU CAN BRANCH WIRE)
a.
C280345C18
1.438,0.281 1.854,0.531 0.417,0.25 1.385,1.948 1.573,1.948 1.573,1.948 1.927,1.323 true 2.563,1.948 2.302,1.948 2.302,1.948 2.063,1.323 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.583,0.313 2,0.542 0.417,0.229 10 false a2 0.948,1.844 1.448,2.01 0.5,0.167 10 false CANH 2.615,1.854 3.115,2.021 0.5,0.167 10 false CANL
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a2-12 (CANH) - a2-13 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE PARKING ASSIST ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
C343114C02
1.469,0.333 1.917,0.531 0.448,0.198 0.427,0.854 0.583,0.854 0.583,0.854 0.906,1.135 true 0.573,0.594 0.729,0.594 0.729,0.594 1.021,1.167 true 0.771,0.333 0.927,0.333 0.927,0.333 1.146,1.156 true 2.521,1.146 2.781,0.948 2.781,0.948 2.927,0.948 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 1.594,0.344 2.021,0.604 0.427,0.26 10 false a2 0.365,0.24 0.802,0.448 0.438,0.208 10 false GND1 0.344,0.479 0.781,0.688 0.438,0.208 10 false +B 0.104,0.75 0.542,0.958 0.438,0.208 10 false ACC 2.99,0.844 3.427,1.052 0.438,0.208 10 false IG
*a Front view of wire harness connector
(to Parking Assist ECU)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a2-2 (+B) - Body ground Always 11 to 14 V
a2-1 (ACC) - Body ground Ignition switch ACC 11 to 14 V
a2-6 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a2-3 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
C343114C02
1.469,0.333 1.917,0.531 0.448,0.198 0.427,0.854 0.583,0.854 0.583,0.854 0.906,1.135 true 0.573,0.594 0.729,0.594 0.729,0.594 1.021,1.167 true 0.771,0.333 0.927,0.333 0.927,0.333 1.146,1.156 true 2.521,1.146 2.781,0.948 2.781,0.948 2.927,0.948 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 1.594,0.344 2.021,0.604 0.427,0.26 10 false a2 0.365,0.24 0.802,0.448 0.438,0.208 10 false GND1 0.344,0.479 0.781,0.688 0.438,0.208 10 false +B 0.104,0.75 0.542,0.958 0.438,0.208 10 false ACC 2.99,0.844 3.427,1.052 0.438,0.208 10 false IG
*a Front view of wire harness connector
(to Parking Assist ECU)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a2-2 (+B) - Body ground Always 10.5 to 16 V
a2-1 (ACC) - Body ground Ignition switch ACC 10.5 to 16 V
a2-6 (IG) - Body ground Ignition switch ON 10.5 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a2-3 (GND1) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (Except GND1 terminals) B
NG (GND1 terminal) C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR