Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Blind Spot Monitor Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptoms Trouble Area
Blind Spot Monitor Sensor Communication Stop Mode Either condition is met:
·

"Blind Spot Monitor Master" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Blind Spot Monitor Sensor Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside blind spot monitor sensor LH

·

Blind spot monitor sensor LH CAN branch wire or connector

·

Blind spot monitor sensor LH



WIRING DIAGRAM

C329326E10
1.531,0.885 2.021,1.354 0.49,0.469 10 false 4 1.542,1.406 2.031,1.875 0.49,0.469 10 false 14 0.271,1.927 0.76,2.396 0.49,0.469 10 false N36 0.271,2.104 2.396,2.427 2.125,0.323 10 false No. 10 CAN Junction Connector 5.427,0.875 5.917,1.344 0.49,0.469 10 false 2 5.427,1.406 5.917,1.875 0.49,0.469 10 false 7 4.083,2.313 4.885,2.583 0.802,0.271 10 false GAUGE 5.427,2.344 5.917,2.813 0.49,0.469 10 false 5 5.656,2.448 6.146,2.917 0.49,0.469 10 false BLB 5.375,3.698 5.865,4.167 0.49,0.469 10 false 10 5.646,3.813 6.135,4.281 0.49,0.469 10 false BLGD 5.104,4.781 5.594,5.073 0.49,0.292 10 false R1 5.104,4.958 7.031,5.219 1.927,0.26 10 false Blind Spot Monitor Sensor LH 3.552,3.427 4.042,3.896 0.49,0.469 10 false *2 0.948,3.26 3.135,3.604 2.188,0.344 10 false from Engine Stop and Start ECU*2 1.594,2.458 3.083,2.781 1.49,0.323 10 false from IG1 NO.2 Relay*1 0.417,4.896 2.927,5.25 2.51,0.354 10 false *1: w/o Stop and Start System 3.51,2.594 4,3.063 0.49,0.469 10 false *1 0.417,5.188 3.073,5.5 2.656,0.313 10 false *2: w/ Stop and Start System 5.656,0.99 6.208,1.354 0.552,0.365 10 false CA1P 5.656,1.5 6.198,1.844 0.542,0.344 10 false CA1N

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and turn the blind spot monitor main switch on, and then wait 8.76 seconds or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH CAN BRANCH WIRE)
a.
C268297C01
1.5,0.167 1.833,0.417 0.333,0.25 0.75,0.667 1,0.667 1,0.667 1.5,1.167 true 0.833,1.833 1.083,1.833 1.083,1.833 1.5,1.333 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.417,1.75 1.031,1.948 0.615,0.198 10 CA1N 1.573,0.208 1.885,0.365 0.313,0.156 10 R1 0.333,0.583 0.948,0.781 0.615,0.198 10 CA1P
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-2 (CA1P) - R1-7 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE BLIND SPOT MONITOR SENSOR LH CAN BRANCH WIRE OR CONNECTOR (CA1P, CA1N)

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)
a.
C268297C02
1.5,0.167 1.833,0.417 0.333,0.25 2.75,0.781 2.448,0.781 2.448,0.781 2,1.156 true 2.729,1.802 2.427,1.802 2.427,1.802 2.01,1.323 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 1.563,0.208 1.875,0.365 0.313,0.156 10 R1 2.802,0.688 3.188,0.885 0.385,0.198 10 BLB 2.802,1.729 3.25,1.948 0.448,0.219 10 BLGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R1-5 (BLB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-10 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)
a.
C268297C02
1.5,0.167 1.833,0.417 0.333,0.25 2.75,0.781 2.448,0.781 2.448,0.781 2,1.156 true 2.729,1.802 2.427,1.802 2.427,1.802 2.01,1.323 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 1.563,0.208 1.875,0.365 0.313,0.156 10 R1 2.802,0.688 3.188,0.885 0.385,0.198 10 BLB 2.802,1.729 3.25,1.948 0.448,0.219 10 BLGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R1-5 (BLB) - Body ground Ignition switch ON 10.5 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-10 (BLGD) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (BLB terminal) B
NG (BLGD terminal) C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR