Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY › from 2015.10
RM3090E _52 Drivetrain _008753 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0051088 AUTOMATIC TRANSAXLE ASSEMBLY A

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

If automatic transmission parts are replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

Hide 1.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C228929

Remove the flywheel housing under cover.


b.
C228931N02
1.208,0.792 0.927,1.74 false 1.615,1.5 1.531,1.74 1.531,1.74 0.792,1.74 false 1.406,1.406 1.292,1.74 false 0.49,1.656 0.781,1.833 0.292,0.177 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-54015  09330-00021  91551-80650  


c.
C281370

Remove the 6 drive plate and torque converter assembly setting bolts.


Hide 2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 28100 3.REMOVE STARTER ASSEMBLY

Hide 4.DISCONNECT WIRE HARNESS

a.

Remove the bolt and disconnect the ground cable from the automatic transaxle assembly.

C280050


b.

Detach the 5 wire harness clamps.


c.

Turn the lock lever and disconnect the connector from the wiring harness connector.


d.

Disconnect the park/neutral position switch connector.


Hide 5.REMOVE WIRE HARNESS CLAMP BRACKET

a.

Remove the 2 bolts and 2 wire harness clamp bracket.

C280049


Hide 6.REMOVE BREATHER HOSE BRACKET

a.
C228915

Detach the transmission breather hose sub-assembly from the breather hose bracket.


b.
C228916

Remove the bolt and breather hose bracket from the automatic transaxle assembly.


Hide 82824 7.REMOVE WIRING HARNESS CONNECTOR

a.
C238952

Remove the 2 bolts and wiring harness connector from the automatic transaxle assembly.


Hide 33493A 8.REMOVE TRANSMISSION OIL COOLER

a.
C280479

Slide the clips and disconnect the oil cooler inlet hose and oil cooler outlet hose from the automatic transaxle assembly.


b.

Remove the 2 bolts and transmission oil cooler from the front engine mounting bracket.


Hide 12311A 9.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C280053

Remove the 4 bolts and front engine mounting bracket from the automatic transaxle assembly.


Hide 12321A 10.REMOVE REAR ENGINE MOUNTING BRACKET

a.
C280469

Remove the 3 bolts and rear engine mounting bracket from the automatic transaxle assembly.


Hide 12325A 11.REMOVE ENGINE MOUNTING BRACKET LH

a.
C280052

Remove the 4 bolts and engine mounting bracket LH from the automatic transaxle assembly.


Hide 33823 12.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C278990

Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.


Hide 35150 13.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C201723

Remove the transmission case plug assembly from the automatic transaxle assembly.


b.

Remove the O-ring from the transmission case plug assembly.


Hide 30500 14.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.
C204173

Remove the 9 bolts and automatic transaxle assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine.



Hide 15.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the automatic transaxle assembly.

NOTICE:

Make sure to remove the torque converter assembly horizontally from the input shaft.



Hide 36100 16.REMOVE TRANSFER ASSEMBLY

Hide 36100A 17.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

C287928


a.

Remove the 2 transfer and transaxle setting stud bolts.

HINT:

It is not necessary to remove the transfer and transaxle setting stud bolts unless they are being replaced.