| Detection Item | Symptom | Trouble Area |
|---|---|---|
| Main Body ECU Communication Stop Mode | Either condition is met:
|
·
Power source or inside main body ECU (multiplex network body ECU) ·
Main body ECU (multiplex network body ECU) CAN branch wire or connector ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following procedure.
DTC check procedure: Wait 20 seconds after turning the ignition switch ACC or ON.
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G78-14 (CANH) - G78-13 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
Connect the cable to the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Remove the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
Reconnect the 3A, 3B, 3C and 3D instrument panel junction block assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: w/o Stop and Start System *2: w/ Stop and Start System |
||
| A-30 (BECU) - Body ground | Always | 11 to 14 V |
| A-32 (IG) - Body ground | Ignition switch ON | 11 to 14 V*1
10.5 to 16 V*2 |
| A-29 (ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-11 (GND1) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Stop and Start System) | B |
| NG (w/ Stop and Start System) | C |
A
B
C
Disconnect the instrument panel junction block assembly connectors.
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-1 - Body ground | Always | 11 to 14 V |
| 3B-16 - Body ground | Always | 11 to 14 V |
| 3C-45 - Body ground | Ignition switch ACC | 11 to 14 V |
| 3D-40 - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-9 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel junction block assembly connectors.
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-1 - Body ground | Always | 11 to 14 V |
| 3B-16 - Body ground | Always | 11 to 14 V |
| 3C-45 - Body ground | Ignition switch ACC | 11 to 14 V |
| 3D-40 - Body ground | Ignition switch ON | 10.5 to 16 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-9 - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (3D-40 terminal) | B |
| NG (Except 3D-40 terminals) | C |
A
B
for 2WW:
for 3ZR-FAE:
C