Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221951 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  Audio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Audio Receiver Assembly Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside radio and display receiver assembly

·

Radio and display receiver assembly CAN branch wire or connector

·

Radio and display receiver assembly



WIRING DIAGRAM

C329332E09
1.552,0.865 2.146,1.208 0.594,0.344 10 false 3 1.542,1.375 2.135,1.719 0.594,0.344 10 false 13 0.188,1.854 0.781,2.198 0.594,0.344 10 false G172 0.188,2.021 2.146,2.323 1.958,0.302 10 false No. 7 CAN Junction Connector 2.156,2.344 3.219,2.667 1.063,0.323 10 false from Battery*1 1.76,3.667 3.365,4 1.604,0.333 10 false from IG1 NO.1 Relay 1.896,4.406 3.146,4.677 1.25,0.271 10 false from ACC Relay*1 0.979,2.885 3.198,3.229 2.219,0.344 10 false from Engine Stop and Start ECU*2 4.208,4.271 4.76,4.542 0.552,0.271 10 false ACC 4.156,2.219 4.75,2.563 0.594,0.344 10 false RADIO 5.24,0.969 5.833,1.313 0.594,0.344 10 false G143 5.323,1.26 5.917,1.604 0.594,0.344 10 false 10 5.354,0.781 5.948,1.125 0.594,0.344 10 false 9 5.656,0.969 6.25,1.313 0.594,0.344 10 false CANH 5.646,1.49 6.24,1.833 0.594,0.344 10 false CANL 5.646,2.333 6.26,2.823 0.615,0.49 10 false +B1 5.365,2.156 5.958,2.5 0.594,0.344 10 false 4 5.344,3.438 5.938,3.781 0.594,0.344 10 false 1 5.656,3.667 6.25,4.01 0.594,0.344 10 false IG 5.354,4.167 5.948,4.51 0.594,0.344 10 false 3 5.344,5.135 5.938,5.479 0.594,0.344 10 false 7 5.646,5.365 6.24,5.708 0.594,0.344 10 false GND1 5.479,5.958 6.667,6.406 1.188,0.448 10 false Radio and Display Receiver Assembly 0.479,5.854 2.781,6.094 2.302,0.24 10 false *1: w/o Stop and Start System 0.469,6.167 3.125,6.625 2.656,0.458 10 false *2: w/ Stop and Start System 5.656,4.396 6.271,4.885 0.615,0.49 10 false ACC1 3.917,3.531 4.927,3.802 1.01,0.271 10 false ECU-IG NO.2 0.969,4.948 3.188,5.292 2.219,0.344 10 false from Engine Stop and Start ECU*2 3.438,2.49 4.031,2.833 0.594,0.344 10 false *1 3.448,3.031 4.042,3.375 0.594,0.344 10 false *2 3.479,5.063 4.073,5.406 0.594,0.344 10 false *2 3.469,4.542 4.063,4.885 0.594,0.344 10 false *1 5.24,1.5 5.833,1.844 0.594,0.344 10 false G143 5.24,2.344 5.833,2.688 0.594,0.344 10 false G141 5.229,3.688 5.823,4.031 0.594,0.344 10 false G143 5.24,4.417 5.833,4.76 0.594,0.344 10 false G141 5.229,5.365 5.823,5.708 0.594,0.344 10 false G141

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
E140414C05
1.469,0.417 1.969,0.698 0.5,0.281 2.083,1.469 2.25,2 2.25,2 2.5,2 true 1.938,1.469 1.833,2 1.833,2 1.667,2 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 2.552,1.906 3.167,2.104 0.615,0.198 10 CANL 1.24,1.917 1.854,2.115 0.615,0.198 10 CANH 1.542,0.469 2,0.667 0.458,0.198 10 G143
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-9 (CANH) - G143-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C277477C06
1.5,0.208 1.938,0.448 0.438,0.24 1.542,1.813 1.979,2.052 0.438,0.24 0.979,2.604 0.802,2.396 0.802,2.396 0.635,2.396 true 2.104,1.479 1.854,1.479 1.854,1.479 1.667,1.146 true 2.573,0.708 2.375,0.708 2.375,0.708 2.198,0.896 true 2.438,0.396 2.24,0.396 2.24,0.396 2,0.885 true 0.448,2.302 0.906,2.5 0.458,0.198 10 IG 2.146,1.396 2.688,1.625 0.542,0.229 10 GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 *a 1.542,0.25 2,0.448 0.458,0.198 10 G141 1.583,1.854 2.042,2.052 0.458,0.198 10 G143 2.615,0.604 3.156,0.833 0.542,0.229 10 +B1 2.469,0.292 3.01,0.521 0.542,0.229 10 ACC1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the radio and display receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G141-4 (+B1) - Body ground Always 11 to 14 V
G143-1 (IG) - Body ground Ignition switch ON 11 to 14 V
G141-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-7 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C277477C06
1.5,0.208 1.938,0.448 0.438,0.24 1.542,1.813 1.979,2.052 0.438,0.24 0.979,2.604 0.802,2.396 0.802,2.396 0.635,2.396 true 2.104,1.479 1.854,1.479 1.854,1.479 1.667,1.146 true 2.573,0.708 2.375,0.708 2.375,0.708 2.198,0.896 true 2.438,0.396 2.24,0.396 2.24,0.396 2,0.885 true 0.448,2.302 0.906,2.5 0.458,0.198 10 IG 2.146,1.396 2.688,1.625 0.542,0.229 10 GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 *a 1.542,0.25 2,0.448 0.458,0.198 10 G141 1.583,1.854 2.042,2.052 0.458,0.198 10 G143 2.615,0.604 3.156,0.833 0.542,0.229 10 +B1 2.469,0.292 3.01,0.521 0.542,0.229 10 ACC1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the radio and display receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G141-4 (+B1) - Body ground Always 10.5 to 16 V
G143-1 (IG) - Body ground Ignition switch ON 11 to 14 V
G141-3 (ACC1) - Body ground Ignition switch ACC 10.5 to 16 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-7 (GND1) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (+B1, ACC1 terminals) B
NG (IG, GND1 terminals) C



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR