Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) J

STOP AND START  STOP AND START SYSTEM(for 2WW)  Stop and Start Priority Control System  


DESCRIPTION

When the steering pad switch assembly is used to select a control mode, a status change request signal is sent from the combination meter assembly to the engine stop and start ECU via CAN communication. Cooperative control is performed by the air conditioning amplifier assembly and engine stop and start ECU based on the selected control mode.

When stop and start priority control (Extended) is selected, the operation time of stop and start control will be extended in order to improve fuel economy.

WIRING DIAGRAM

A375522E01
2.146,1.417 4.031,1.677 1.885,0.26 10 false Combination Meter Assembly 2.135,1.219 2.594,1.417 0.458,0.198 10 false G16 2.427,0.51 3.042,0.708 0.615,0.198 10 false STRG 2.135,0.385 2.448,0.583 0.313,0.198 10 false 28 0.979,1.583 1.292,1.781 0.313,0.198 10 false G8 1.323,1.583 1.635,1.781 0.313,0.198 10 false 10 0.354,1.583 0.667,1.781 0.313,0.198 10 false G8 0.677,1.583 0.99,1.781 0.313,0.198 10 false 11 1.115,1.813 1.573,2.01 0.458,0.198 10 false +DP 0.51,1.823 0.969,2.021 0.458,0.198 10 false -DP 0.969,2.292 1.281,2.49 0.313,0.198 10 false z1 1.323,2.302 1.479,2.5 0.156,0.198 10 false 2 0.375,2.292 0.688,2.49 0.313,0.198 10 false z1 0.698,2.302 0.854,2.5 0.156,0.198 10 false 3 1.5,2.688 3.604,2.885 2.104,0.198 10 false Steering Pad Switch Assembly 1.594,1.948 4.104,2.188 2.51,0.24 10 false Spiral Cable with Sensor Sub-assembly 3.51,0.563 4.125,0.76 0.615,0.198 10 false CANH 3.531,0.948 4.146,1.146 0.615,0.198 10 false CANL 4,0.406 4.313,0.604 0.313,0.198 10 false 32 4,0.76 4.313,0.958 0.313,0.198 10 false 31 5.135,0.563 5.75,0.76 0.615,0.198 10 false CANH 5.146,0.948 5.76,1.146 0.615,0.198 10 false CANL 4.875,0.396 5.188,0.594 0.313,0.198 10 false 13 4.885,0.771 5.198,0.969 0.313,0.198 10 false 14 4.979,1.458 6.74,1.698 1.76,0.24 10 false Engine Stop and Start ECU 4.979,1.281 5.438,1.479 0.458,0.198 10 false G87 4.75,3.729 7.073,3.99 2.323,0.26 10 false Air Conditioning Amplifier Assembly 4.75,2.667 5.208,2.865 0.458,0.198 10 false G80 4.74,3.365 5.198,3.563 0.458,0.198 10 false G80 5.146,2.667 5.604,2.865 0.458,0.198 10 false G81 5.156,3.365 5.615,3.563 0.458,0.198 10 false G81 4.802,2.427 5.26,2.625 0.458,0.198 10 false 8*1 4.813,3.135 5.271,3.333 0.458,0.198 10 false 9*1 5.156,2.438 5.469,2.635 0.313,0.198 10 false 11*2 5.156,3.146 5.469,3.344 0.313,0.198 10 false 12*2 5.542,2.656 6.156,2.854 0.615,0.198 10 false CANH 5.542,3.365 6.156,3.563 0.615,0.198 10 false CANL 0.573,4.469 4.24,4.667 3.667,0.198 10 false : CAN Communication Line 0.448,3.521 2.604,3.719 2.156,0.198 10 false *1: for Manual Air Conditioning 0.448,3.896 2.604,4.094 2.156,0.198 10 false *2: for Automatic Air Conditioning

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION



HINT:
·

When stop and start priority control (Extended) is selected, the operation of the air conditioning system is limited. If the customer reports that the cooling effectiveness of the air conditioning system is poor, check the selected control mode. If stop and start priority control (Extended) is selected, cancel the control mode and check if the cooling effectiveness of the air conditioning system improves. If it improves, explain to the customer that the operation of the air conditioning system was limited by stop and start control.

·

Depending on the vehicle conditions, the stop and start operation time may not change even if stop and start priority control (Extended) is selected.



PROCEDURE

1.CHECK PROBLEM SYMPTOMS
a.

Check the problem symptoms.

HINT:
·

Check each symptom by checking the suspected areas in the table below.

·

By using the GTS and entering the following menus, the selected mode can be confirmed.

Powertrain / Stop and Start / Data List / Stop & Start A/C Mode



Result:
Problem Symptoms Trouble Area Proceed to
Multi-information display screen does not change after pressing steering pad switch assembly
·

Steering pad switch assembly

·

Spiral cable with sensor sub-assembly

·

Combination meter assembly

·

Engine stop and start ECU

·

Wire harness or connector (steering pad switch assembly - combination meter assembly)

·

Wire harness or connector (engine stop and start ECU - combination meter assembly)


A
Multi-information display screen changes without pressing steering pad switch assembly
·

Steering pad switch assembly

·

Spiral cable with sensor sub-assembly

·

Wire harness or connector (steering pad switch assembly - combination meter assembly)


B
Multi-information display screen does not change but control mode changes Combination meter assembly C
Multi-information display screen changes but control mode does not change
·

Air conditioning amplifier assembly

·

Wire harness or connector (engine stop and start ECU - air conditioning amplifier assembly)


D
Control mode returns to default mode after turning ignition switch to ON Engine stop and start ECU E




A

2.CHECK OPERATION

B

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

C

D

10.CHECK DTC OUTPUT

E

11.CHECK DTC OUTPUT
2.CHECK OPERATION
a.

Using the steering pad switch assembly, check that all functions other than "Stop and Start A/C Mode" can be selected.

Result:
Result Proceed to
Only "Stop and Start A/C Mode" cannot be selected A
No function can be selected using the steering pad switch assembly B




A

3.CHECK DTC OUTPUT

B

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Perform a road test.


e.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

Powertrain > Stop and Start > Trouble Codes
50001 227

f.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
CAN DTCs are output B




A

B

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the G8 spiral cable with sensor sub-assembly connector.


c.

Disconnect the G16 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-10 (+DP) - G16-28 (STRG) Always Below 1 Ω
G8-10 (+DP) - Body ground Always 10 kΩ or higher
G16-28 (STRG) - Body ground Always 10 kΩ or higher
G8-11 (-DP) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Result:
Proceed to
OK
NG



OK

6.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

6.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the G8 spiral cable with sensor sub-assembly connector.


c.

Disconnect the G16 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-10 (+DP) - G16-28 (STRG) Always Below 1 Ω
G8-10 (+DP) - Body ground Always 10 kΩ or higher
G16-28 (STRG) - Body ground Always 10 kΩ or higher
G8-11 (-DP) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Result:
Proceed to
OK
NG



OK

9.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

9.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

10.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Perform a road test.


e.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

Powertrain > Stop and Start > Trouble Codes
50001 227

f.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
CAN DTCs are output B




A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

11.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Perform a road test.


e.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

Powertrain > Stop and Start > Trouble Codes
50001 227

f.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
DTCs are output B




A

B