Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for LH Side) › from 2015.10
RM3090E _58 Vehicle Interior _008433 SEAT _0049737 REAR SEAT ASSEMBLY(for LH Side) A

SEAT  REAR SEAT ASSEMBLY(for LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.


PROCEDURE

Hide 87510P 1.INSTALL REAR SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71078S 2.INSTALL SEPARATE TYPE REAR SEATBACK COVER

a.
B340941C01
1.771,1.49 2.104,0.406 2.104,0.406 2.406,0.406 false 2.469,0.281 2.781,0.438 0.313,0.156 10 *1
*1 Hog Ring Pliers


Set the separate type rear seatback cover in place.


b.

Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 11 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




c.
B340942C01
1.813,1.49 2.031,0.417 2.031,0.417 2.406,0.417 false 2.458,0.313 2.771,0.469 0.313,0.156 10 *1
*1 Hog Ring Pliers


Using hog ring pliers, install 5 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




Hide 3.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD

a.
B429026

Attach the 9 hooks to install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.


b.
B340586

Attach the 8 claws to install the 4 rear seat headrest supports.


c.
B429025

Attach the 9 hooks.


Hide 71882A 4.INSTALL REAR SEATBACK BOARD LH

a.
B429024

Move the rear seatback board LH in the direction of the arrow to attach the guide.


b.

Attach the 7 claws to install the rear seatback board assembly LH.


c.
B429022

Close the 2 fasteners.


d.
B429020C01
1.792,3.865 1.927,3.031 1.927,3.031 2.063,3.031 false 2.146,2.938 2.458,3.094 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install 6 new hog rings and attach the 2 pieces of fastener.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




Hide 5.INSTALL REAR NO. 1 SEATBACK ASSEMBLY LH

a.
B340583

Install the rear No. 1 seatback assembly LH to the rear seat reclining adjuster assembly LH with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73380D 6.INSTALL REAR SEAT INNER BELT ASSEMBLY LH

a.
B340582

Install the rear seat inner belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 72380 7.INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY

a.
B434004C01
1.667,2.802 2.083,2.385 true 2.292,2.708 3.094,2.542 true 0.573,0.438 1.385,0.656 true 1.479,1.854 1.76,1.583 false 1.49,1.854 1.917,1.844 false 0.552,0.823 0.271,1.24 true 2.958,2.885 2.25,3.052 true 1.521,2.823 1.729,2.99 0.208,0.167 10 false *1 1.313,1.813 1.479,2 0.167,0.188 10 false *3 0.167,1.271 0.375,1.427 0.208,0.156 10 false *4 1.438,0.594 1.646,0.76 0.208,0.167 10 false *2 2.104,2.635 2.281,2.813 0.177,0.177 10 false *2 2.094,3 2.302,3.156 0.208,0.156 10 false *4 0.208,0.729 0.417,0.938 0.208,0.208 10 false (1) 3.135,2.802 3.344,3.01 0.208,0.208 10 true (1) 0.875,0.198 1.083,0.406 0.208,0.208 10 true (2) 2.719,2.281 2.906,2.469 0.188,0.188 10 true (2)
*1 Cable Clamp A
*2 Cable End
*3 Clamp
*4 Cable Clamp B


Pass the No. 2 seat adjuster control cable assembly through the hole of the rear seat reclining adjuster assembly LH.


b.

Attach the cable clamp (A).


c.

Install the 2 clamps.


d.

Connect the 2 cable ends in the order shown in the illustration.


e.

Attach the 2 cable clamps (B).


Hide 71829B 8.INSTALL REAR SEAT REAR CUSHION MOULDING LH

a.
B340580C01
0.302,2.625 0.625,2.406 true 0.969,1.375 1.469,1.177 true 1.479,2.188 1.719,3.104 true 0.104,2.615 0.302,2.781 0.198,0.167 10 false *1 1.521,1.083 1.833,1.24 0.313,0.156 10 false *2 1.667,3.135 1.865,3.302 0.198,0.167 10 false *1
*1 Clamp
*2 Guide


Attach the guide and claw to install the rear seat rear cushion moulding LH.


b.

w/ Seat Belt Warning System:

Attach the 2 clamps to connect the wire harness.


Hide 71826B 9.INSTALL REAR SEAT CUSHION MOULDING LH

a.
B340577

Attach the 3 guides and claw to install the rear seat cushion moulding LH.


Hide 71303C 10.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH (w/ Child Restraint System Guide)

a.
B429018

Attach the 2 claws to install the rear seatback hinge sub-assembly RH.


Hide 71304C 11.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH (w/ Child Restraint System Guide)

a.
B429016

Attach the 2 claws to install the rear seatback hinge sub-assembly LH.


Hide 72995A 12.INSTALL REAR SEAT COVER

a.
B340579

w/o Child Restraint System Guide:

i.

Attach the claw to install the rear seat cover.


ii.

Install the clip and screw.



b.
B429014

w/ Child Restraint System Guide:

i.

Attach the 4 claws to install the rear seat cover.


ii.

Install the screw.



Hide 72996 13.INSTALL REAR SEATBACK COVER RH

a.
B340578

w/o Child Restraint System Guide:

i.

Attach the claw to install the rear seatback cover RH.


ii.

Install the clip and screw.



b.
B429012

w/ Child Restraint System Guide:

i.

Attach the 4 claws to install the rear seatback cover RH.


ii.

Install the screw.



Hide 71016A 14.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

a.
B429010

Install the rear seat cushion frame sub-assembly LH with the 4 bushes and 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the No. 2 seat adjuster control cable assembly to the rear seat cushion frame sub-assembly LH with the 3 clamps.

B434005C01
2.344,0.688 3.021,0.344 true 1.667,0.875 1.823,0.698 true 1.854,1.49 2.167,1.333 true 4.979,0.625 5.438,0.719 true 5.073,1.083 5.208,1.375 true 3.052,0.219 3.365,0.375 0.313,0.156 10 false *1 4.792,0.552 4.979,0.729 0.188,0.177 10 false *2 1.542,0.927 1.854,1.083 0.313,0.156 10 true *1 2.208,1.229 2.427,1.385 0.219,0.156 10 true *1 5.146,1.427 5.458,1.583 0.313,0.156 10 false *3 5.688,1.042 5.917,1.271 0.229,0.229 10 false (1) 5.229,0.188 5.458,0.417 0.229,0.229 10 false (2)
*1 Clamp *2 Cable End
*3 Cable Clamp - -



c.

Connect the cable end in the order shown in the illustration.


d.

Attach the cable clamp.


Hide 72996A 15.INSTALL REAR SEATBACK COVER

a.
B434006

Attach the 2 claws to install the rear seatback cover.


Hide 87510Q 16.INSTALL REAR SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71076S 17.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.
B340943C01
1.844,1.479 2.031,0.427 2.031,0.427 2.375,0.427 false 2.448,0.292 2.76,0.448 0.313,0.156 10 *1
*1 Hog Ring Pliers


Set the separate type rear seat cushion cover in place.


b.

Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad LH with 13 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




c.
B429008C01
1.708,3.729 1.75,2.74 1.75,2.74 1.948,2.74 false 2,2.656 2.313,2.813 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install 2 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




Hide 18.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

a.
B429006C01
1.74,2.781 1.688,2.104 1.688,2.104 1.906,2.104 false 1.958,2.042 2.271,2.198 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install 3 new hog rings.


b.

Install the separate type seat cushion cover with pad to the rear seat cushion frame sub-assembly LH with the 22 hooks.

B429004


c.
B429003

w/ Seat Heater System:

i.

Connect the connector.


ii.

Attach the 4 clamps to connect the wire harness.



Hide 71694 19.INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH

a.
B336610

Attach the guide and 4 claws to install the rear seat lower cushion hinge cover LH.


Hide 71693A 20.INSTALL REAR SEAT NO. 3 CUSHION HINGE COVER

a.
B336609

Attach the guide and 4 claws to install the rear seat No. 3 cushion hinge cover.


Hide 72526A 21.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.
B336614

Install the reclining adjuster release handle LH with the 3 screws.


Hide 71846B 22.INSTALL REAR SEATBACK NO. 1 BOARD CAP

a.
B434007

Attach the 3 claws to install the rear seatback No. 1 board cap.


Hide 72831B 23.INSTALL REAR SEAT NO. 1 CENTER ARMREST PLATE

a.
B434008

Install the rear seat No. 1 center armrest plate.


Hide 72830 24.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

a.
B336611

Install the rear seat center armrest assembly with the washer and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72868 25.INSTALL CENTER ARMREST HINGE COVER RH

a.
B429000

Attach the claw to install the center armrest hinge cover RH.


Hide 73340C 26.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY LH

Hide 71960B 27.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY

a.

Install the rear seat center headrest assembly.


Hide 71940A 28.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the rear seat headrest assembly.