Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _008784 METER / GAUGE / DISPLAY _0050254 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The combination meter assembly receives vehicle speed signals from the brake actuator assembly (skid control ECU) via the CAN communication line. The wheel speed sensors output voltages that vary according to the vehicle speed. The brake actuator assembly (skid control ECU) supplies power to the wheel speed sensors. The brake actuator assembly (skid control ECU) calculates the vehicle speed based on the pulses of the voltage.

WIRING DIAGRAM

E200122E16
1.052,2.635 2.677,3.146 1.625,0.51 10 Brake Actuator Assembly (Skid Control ECU) 0.802,3.365 2.615,3.542 1.813,0.177 10 : CAN Communication Line 4.49,2.729 6.344,2.906 1.854,0.177 10 Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK).

·

When replacing the combination meter assembly, make sure to replace it with a new one.



HINT:

Before starting the following inspection, check the tire size and tire air pressure.


PROCEDURE

1.CHECK FOR DTC

OK:

DTCs U0100, U0129, U0131, U0142, U0151, U0163, U023A and U1104 are not output.


Result:
Proceed to
OK
NG



OK

2.CHECK ANTI-LOCK BRAKE SYSTEM OR VEHICLE STABILITY CONTROL SYSTEM

NG

2.CHECK ANTI-LOCK BRAKE SYSTEM OR VEHICLE STABILITY CONTROL SYSTEM
a.

Check if a vehicle stability control system DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

DTC is not output



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)

NG

3.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speed Meter Operation Speedometer OFF, 0, 40, 80, 120, 160 or 200 (km/h or mph) Acceptable range (km/h or mph): [Control range → Speedometer display]
for Australia
·

40 → 40.6 to 45.1

·

80 → 81.2 to 86.2

·

120 → 121.8 to 126.8

·

160 → 162.4 to 167.4

·

200 → 203 to 208


except Australia (km/h)
·

40 → 41.7 to 46.2

·

80 → 83.4 to 88.4

·

120 → 125.1 to 130.6

·

160 → 166.2 to 173.2

·

200 → 207.7 to 215.7


except Australia (MPH)
·

40 → 42 to 44.5

·

80 → 83.1 to 87.1

·

120 → 124.7 to 129.6


Body Electrical > Combination Meter > Active Test
Tester Display
Speed Meter Operation
50004 122 1
OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (VEHICLE SPEED METER, VEHICLE SPEED)

NG

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING GTS (VEHICLE SPEED METER, VEHICLE SPEED)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 mph (0 km/h), Max.: 255 km/h (158 mph) Almost same as actual vehicle speed measured using a speedometer tester -
Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 mph (0 km/h), Max.: 326 km/h (202 mph) Almost same as actual vehicle speed measured using a speedometer tester -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 122 8
Chassis > ABS/VSC/TRC > Data List
Tester Display
Vehicle Speed
50003 105 42
HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the brake actuator assembly (skid control ECU) or an internal malfunction of the combination meter assembly is suspected.




Result:
Proceed to
The Data List values of the ECUs match
The Data List values of the ECUs do not match



The Data List values of the ECUs match

REPLACE COMBINATION METER ASSEMBLY

The Data List values of the ECUs do not match

5.CHECK COMBINATION METER ASSEMBLY
5.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or normally functioning one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Check that the operation of the speedometer returns to nomal.

OK:

The operation of the speedometer returns to normal.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE)

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)