Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2015.10
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0049518 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.
B337368

Using a moulding remover, detach the 2 clips, 5 claws and 2 guides and remove the rear power window regulator switch assembly with rear door armrest base panel.


b.

Disconnect the connector.


c.

w/ Seat Heater System:

Disconnect the connector.


Hide 84810D 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 84751R 5.REMOVE REAR SEAT HEATER SWITCH (w/ Seat Heater System)

Hide 74646A 6.REMOVE DOOR ASSIST GRIP COVER LH

a.
B337369

Using a moulding remover, detach the 5 claws, 2 clips and guide and remove the door assist grip cover LH.


Hide 69284D 7.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH

a.
B337370

Detach the 3 claws and remove the rear door inside bezel plug LH.


Hide 67604 8.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B337371

Remove the 3 screws.


b.

Detach the 8 clips and remove the rear door trim board sub-assembly LH.


c.
B337372

Disengage the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH from the 2 clamps.


d.

Disconnect the rear door lock remote control cable and rear door inside locking cable LH.


Hide 69206C 9.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B337373

Detach the 2 claws and guide and remove the rear door inside handle sub-assembly LH.


Hide 68174A 10.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B337374

Raise the 6 claws of the rear door inner glass weatherstrip LH as shown in the illustration, and then remove the rear door inner glass weatherstrip LH from the rear door trim board sub-assembly LH.


Hide 86160B 11.REMOVE REAR SPEAKER ASSEMBLY (w/ Speaker)

Hide 86262D 12.REMOVE REAR DOOR SPEAKER COVER (w/o Speaker)

a.
B338207

Disconnect the connector.


b.

Put a 4 mm (0.157 in.) drill bit into a drill.


c.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

NOTICE:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



d.

Lightly press the drill against the 3 rivets, drill off the flanges of the 3 rivets and remove the rear door speaker cover.

B337336C02
2.313,0.385 2.51,0.563 0.198,0.177 10 A

Standard
Area Specified Condition
A 5 mm (0.197 in.)

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




e.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


Hide 67842E 13.REMOVE REAR DOOR SERVICE HOLE COVER LH

a.
B338200

Disconnect the connector of the rear door lock assembly LH.


b.

Pull out the rear door lock remote control cable LH, rear door inside locking cable LH and wire harness from the rear door service hole cover LH, and then remove the rear door service hole cover LH.

HINT:

Remove any remaining butyl tape from the rear door panel.



Hide 67408E 14.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

a.

Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.


b.

Connect the cable to the negative (-) battery terminal.


c.

Move the rear door window regulator sub-assembly LH so that the rear door glass channel can be seen.


d.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Remove the rear power window regulator switch assembly with rear door armrest base panel.


f.
B337376

Remove the screw and 2 bolts.


g.
B338210

Remove the rear door window division bar sub-assembly LH together with the rear door glass run as shown in the illustration.


h.

Remove the rear door window division bar sub-assembly LH from the rear door glass run LH.


Hide 68124B 15.REMOVE REAR DOOR QUARTER WINDOW GLASS LH

a.
B337379

Remove the rear door quarter window glass LH.


Hide 68189 16.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.
B337380

Remove the rear door quarter window weatherstrip LH from the rear door quarter window glass LH.


Hide 68104 17.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

a.
B337381

Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.

NOTICE:

Do not damage the door glass.



Hide 69906B 18.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH

a.
B337382C02
1.292,1.156 1.615,0.708 false 1.615,0.573 1.927,0.729 0.313,0.156 10 *1
*1 Protective Tape


Using a screwdriver, remove the rear door glass channel sub-assembly LH.

HINT:

Tape the screwdriver tip before use.



Hide 69975A 19.REMOVE REAR DOOR GLASS CHANNEL FILLER

a.
B337383

Remove the rear door glass channel filler.


Hide 68152C 20.REMOVE REAR DOOR GLASS RUN LH

a.
B337378

Remove the front side of the rear door glass run LH.


Hide 69804 21.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B337384C01
1.75,0.542 1.875,0.365 1.875,0.365 2.177,0.365 false 2.219,0.281 2.365,0.448 0.146,0.167 10 *1
*1 Temporary Bolt


Disconnect the connector.


b.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and become damaged.



c.

Remove the 3 bolts and rear door window regulator sub-assembly LH.


d.

Remove the temporary bolt from the rear door window regulator sub-assembly LH.


Hide 85720D 22.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 75740 23.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 69060A 24.REMOVE REAR DOOR WITH MOTOR LOCK ASSEMBLY LH

Hide 69740D 25.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B338208C02
0.01,0.042 0.323,0.198 0.313,0.156 10 *A 0.031,2.313 0.344,2.469 0.313,0.156 10 *B
*A w/o Double Locking System
*B w/ Double Locking System


Detach the claw and open the cover.


b.
B337388C02
0.177,0.073 0.49,0.229 0.313,0.156 10 *A 0.26,1.615 0.573,1.771 0.313,0.156 10 *B
*A w/o Double Locking System
*B w/ Double Locking System


Remove the rear door lock remote control cable LH.


Hide 69780B 26.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B338208C04
0.031,0.042 0.344,0.198 0.313,0.156 10 *A 0,2.208 0.313,2.365 0.313,0.156 10 *B
*A w/o Double Locking System
*B w/ Double Locking System


Detach the 3 claws and open the cover.


b.
B337389C02
0.219,0.104 0.531,0.26 0.313,0.156 10 *A 0.323,1.688 0.635,1.844 0.313,0.156 10 *B
*A w/o Double Locking System
*B w/ Double Locking System


Remove the rear door inside locking cable assembly LH.


Hide 67836H 27.REMOVE REAR DOOR LOCK CHILD PROTECTION COVER LH

a.
B337390

Remove the rear door lock child protection cover LH.


Hide 69227L 28.REMOVE REAR DOOR OUTSIDE HANDLE COVER LH

a.
B337391

Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle cover LH.


Hide 69240 29.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B338206

Pull and hold the release plate of the rear door outside handle frame sub-assembly LH as shown in the illustration.

HINT:

The release plate may interfere with the rear door outside handle assembly and may be damaged when removing the rear door outside handle assembly, unless the release plate of the rear door outside handle frame sub-assembly is pulled and held.



b.
B337392

Remove the rear door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow shown in the illustration.


Hide 69241G 30.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B337393

Detach the 3 claws and remove the rear door front outside handle pad.


Hide 69242G 31.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B337394

Detach the 2 claws and remove the rear door rear outside handle pad.


Hide 69204A 32.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B338205C01
0.042,0.052 0.354,0.25 0.313,0.198 10 *A 0.042,1.813 0.354,2.01 0.313,0.198 10 *B
*A Inside
*B Outside


Using a T30 "TORX" socket wrench, loosen the screw.


b.

Slide the rear door outside handle frame sub-assembly LH to detach the claw of the rear door outside handle frame sub-assembly LH, and then remove it.


Hide 68640A 33.REMOVE REAR DOOR CHECK ASSEMBLY LH

a.
B337398

Remove the 3 bolts and rear door check assembly LH.


Hide 67872 34.REMOVE REAR DOOR WEATHERSTRIP LH

a.
B337399

Detach the 19 clips and remove the rear door weatherstrip LH.


Hide 67674A 35.REMOVE REAR DOOR FRAME GARNISH LH

a.
B337397

Detach the claw and remove the rear door frame garnish LH.


Hide 75792 36.REMOVE DOOR WINDOW FRAME MOULDING CLIP

Hide 75076 37.REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 75988E 38.REMOVE REAR DOOR OUTSIDE STRIPE LH

Hide 75978H 39.REMOVE REAR DOOR LOWER OUTSIDE STRIPE LH

Hide 75078 40.REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 67003C 41.REMOVE REAR DOOR PANEL CUSHION

a.
B337400

Detach the 2 claws and remove the rear door panel cushion.