Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor) › from 2015.10
RM3090E _59 Vehicle Exterior _008795 WIPER / WASHER _0050248 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  Washer Nozzle Heater Circuit  


DESCRIPTION

The main body ECU receives ambient air temperature information from the air conditioning amplifier assembly via CAN communication. The washer nozzle heater assembly controls the main body ECU and operates the washer nozzle heater assembly according to the ambient temperature.

WIRING DIAGRAM

E296776E04
5.51,1.938 5.969,2.135 0.458,0.198 10 false G9 5.5,2.115 6.729,2.531 1.229,0.417 10 false Combination Meter Assembly 5.781,1.188 6.396,1.385 0.615,0.198 10 false WLVL 5.5,1.052 5.813,1.25 0.313,0.198 10 false 17 2.094,1.552 2.552,1.75 0.458,0.198 10 false A59 2.073,1.75 3.406,2.104 1.333,0.354 10 false Level Warning Switch Assembly 3.333,1.042 3.49,1.24 0.156,0.198 10 false 1 2.125,1.052 2.281,1.25 0.156,0.198 10 false 2 3.052,1.281 3.208,1.479 0.156,0.198 10 false S 2.375,1.292 2.531,1.49 0.156,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK MAIN BODY ECU
a.

Using the GTS, enter the following menus: Body / Main Body / Active Test.


b.

Select "Front Washer Nozzle Heater", and perform the Active Test.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM(w/ Rain Sensor)>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Washer Nozzle Heater Washer nozzle heater operation ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Washer Nozzle Heater
50004 123 73

c.

Measure the voltage according to the value(s) in thetable below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G79-20 (WHTR) - Body ground Ignition switch ON
Active Test is not performed
11 to 14 V
Ignition switch ON
Active Test is performed
Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT WASHER NOZZLE SUB-ASSEMBLY

NG

6.INSPECT WASHER HEATER RELAY
2.INSPECT WASHER NOZZLE SUB-ASSEMBLY
a.

Remove the washer nozzle sub-assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER NOZZLE>REMOVAL


b.

Inspect the washer nozzle sub-assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER NOZZLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (WASHER NOZZLE - WASHER HEATER RELAY AND BODY GROUND)

NG

REPLACE WASHER NOZZLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (WASHER NOZZLE - WASHER HEATER RELAY AND BODY GROUND)
a.

Disconnect the A96 washer nozzle sub-assembly connector.


b.

Remove the washer heater relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A96-2 (B) - WASHER HEATER RELAY 3 Always Below 1 Ω
A96-1 (E) - Body ground Always Below 1 Ω
A96-2 (B) or WASHER HEATER RELAY 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT WASHER HEATER RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT WASHER HEATER RELAY
a.

Inspect the washer heater relay.

Click hereVehicle Exterior>WIPER / WASHER>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (WASHER HEATER RELAY - BATTERY)

NG

REPLACE WASHER HEATER RELAY

5.CHECK HARNESS AND CONNECTOR (WASHER HEATER RELAY - BATTERY)
a.

Remove the washer heater relay.


b.

Measure the voltage according to the value(s) in thetable below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
WASHER HEATER RELAY 5 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT WASHER HEATER RELAY
a.

Inspect the washer heater relay.

Click hereVehicle Exterior>WIPER / WASHER>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - WASHER HEATER RELAY)

NG

REPLACE WASHER HEATER RELAY

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - WASHER HEATER RELAY)
a.

Disconnect the G79 main body ECU connector.


b.

Remove the washer heater relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-20 (WHTR) - WASHER HEATER RELAY 2 Always Below 1 Ω
G79-20 (WHTR) or WASHER HEATER RELAY 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (WASHER HEATER RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (WASHER HEATER RELAY - BATTERY)
a.

Remove the washer heater relay.


b.

Measure the voltage according to the value(s) in thetable below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
WASHER HEATER RELAY 1 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
WASHER HEATER RELAY 5 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR