The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Using the GTS, read the Data List.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Pos | Front door unlock detection switch RH signal | UNLOCK or LOCK | UNLOCK: Front door RH unlocked
LOCK: Front door RH locked |
- |
| FL Door Lock Pos | Front door unlock detection switch LH signal | UNLOCK or LOCK | UNLOCK: Front door LH unlocked
LOCK: Front door LH locked |
- |
| RR-Door Lock Pos SW | LH and RH side rear door unlock detection switch signal | ON or OFF | ON: LH or RH side rear door unlocked
OFF: LH and RH side rear door locked |
w/ Entry and Start System or Theft Deterrent System |
| RL-Door Lock Pos SW | LH and RH side rear door unlock detection switch signal | ON or OFF | ON: LH or RH side rear door unlocked
OFF: LH and RH side rear door locked |
w/ Entry and Start System or Theft Deterrent System |
| Tester Display |
|---|
| FR Door Lock Pos |
| FL Door Lock Pos |
| RR-Door Lock Pos SW |
| RL-Door Lock Pos SW |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Front door unlock detection switch RH does not operate) | B |
| NG (Front door unlock detection switch LH does not operate) | C |
| NG (Rear door unlock detection switch does not operate) (w/ Entry and Start System or Theft Deterrent System) | D |
A
B
C
D
Remove the front door with motor lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door with motor lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G78 main body ECU (multiplex network body ECU) connector.
Disconnect the I10 front door with motor lock assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I10-7 (LSSR) - G78-18 (LSFR) | Always | Below 1 Ω |
| I10-8 (E) - Body ground | Always | Below 1 Ω |
| I10-7 (LSSR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
Remove the front door with motor lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door with motor lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G78 main body ECU (multiplex network body ECU) connector.
Disconnect the J10 front door with motor lock assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J10-8 (LSSR) - G78-7 (LSFL) | Always | Below 1 Ω |
| J10-7 (E) - Body ground | Always | Below 1 Ω |
| J10-8 (LSSR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
Remove the rear door with motor lock assembly LH.
Inspect the rear door with motor lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear door with motor lock assembly RH.
Inspect the rear door with motor lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3E instrument panel junction block assembly connector
Disconnect the L4 rear door with motor lock assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-5 (LSSR) - 3E-32 | Always | Below 1 Ω |
| L4-6 (E) - Body ground | Always | Below 1 Ω |
| L4-5 (LSSR) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-6 (LSSR) - 3E-32 | Always | Below 1 Ω |
| L4-9 (E) - Body ground | Always | Below 1 Ω |
| L4-6 (LSSR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3C instrument panel junction block assembly connector
Disconnect the K4 rear door with motor lock assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-9 (LSSR) - 3C-41 | Always | Below 1 Ω |
| K4-10 (E) - Body ground | Always | Below 1 Ω |
| K4-9 (LSSR) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-6 (LSSR) - 3C-41 | Always | Below 1 Ω |
| K4-9 (E) - Body ground | Always | Below 1 Ω |
| K4-6 (LSSR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-5 (LSR) - 3E-32 | Always | Below 1 Ω |
| A-5 (LSR) - 3C-41 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL