Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.10–2016.08
RM3090E _58 Vehicle Interior _008784 METER / GAUGE / DISPLAY _0050254 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1507 Open in Turn Signal Circuit Both conditions are met:
·

IG voltage is 10.5 V or higher.

·

Open in turn signal light circuit.


·

Bulb

·

Harness or connector

·

Side turn signal light assembly

·

Outer rear view mirror sub-assembly

·

Rear combination light socket and wire sub-assembly

·

Combination meter assembly


B1508 Short in Turn Signal / Hazard Flasher Circuit Both conditions are met:
·

IG voltage is 10.5 V or higher.

·

Short in turn signal light circuit or hazard warning light circuit.


·

Bulb

·

Harness or connector

·

Side turn signal light assembly

·

Outer rear view mirror sub-assembly

·

Rear combination light socket and wire sub-assembly

·

Combination meter assembly



WIRING DIAGRAM

E267448E06
5.302,8.365 7.156,8.656 1.854,0.292 10 false Combination Meter Assembly 5.302,8.208 5.667,8.417 0.365,0.208 10 false G17 0.177,0.531 1.917,0.875 1.74,0.344 10 false Front Turn Signal Light RH 0.167,0.365 1.146,0.563 0.979,0.198 10 false A42 2.521,0.406 3.115,0.625 0.594,0.219 10 false 2 2.521,0.646 3.188,0.896 0.667,0.25 10 false 1 2.333,0.427 2.698,0.635 0.365,0.208 10 false B 2.333,0.667 2.698,0.875 0.365,0.208 10 false E 5.854,0.396 6.219,0.604 0.365,0.208 10 false 7 6.052,0.5 6.417,0.708 0.365,0.208 10 false LR 0.135,3.333 2.729,3.552 2.594,0.219 10 false Outer Rear View Mirror Assembly RH*3 1.896,2.094 3.323,2.646 1.427,0.552 10 false Outer Rear View Mirror Sub-assembly RH 0.333,2.104 1.563,2.635 1.229,0.531 10 false Side Turn Signal Light Assembly RH 3.427,1.365 3.792,1.573 0.365,0.208 10 false B 3.427,1.74 3.792,1.948 0.365,0.208 10 false E 3.604,1.354 4.354,1.573 0.75,0.219 10 false 10*1, 4*2 3.615,1.74 4.406,2.01 0.792,0.271 10 false 11*1, 12*2 0.083,8.479 2.083,8.75 2,0.271 10 false *3: w/ Side Turn Signal Light 2.865,3.677 4.604,4.021 1.74,0.344 10 false Rear Turn Signal Light RH 1.552,4.073 5.302,4.292 3.75,0.219 10 false Rear Combination Light Socket and Wire Sub-assembly RH 0.135,3.188 0.865,3.406 0.729,0.219 10 false I8*1, I14*2 1.542,3.917 1.906,4.125 0.365,0.208 10 false M19 5.01,3.563 5.375,3.771 0.365,0.208 10 false 3 5.021,3.813 5.385,4.021 0.365,0.208 10 false 4 4.646,3.573 5.01,3.781 0.365,0.208 10 false TRN 4.813,3.813 5.177,4.021 0.365,0.208 10 false E 6.052,4.479 6.417,4.688 0.365,0.208 10 false LL 5.781,4.375 6.146,4.583 0.365,0.208 10 false 13 0.219,4.365 1.156,4.573 0.938,0.208 10 false A16 0.219,4.521 1.958,4.865 1.74,0.344 10 false Front Turn Signal Light LH 2.333,4.406 2.698,4.615 0.365,0.208 10 false B 2.333,4.635 2.698,4.844 0.365,0.208 10 false E 2.542,4.375 3.25,4.573 0.708,0.198 10 false 2 2.531,4.625 3.156,4.844 0.625,0.219 10 false 1 0.146,7.323 2.74,7.552 2.594,0.229 10 false Outer Rear View Mirror Assembly LH*3 0.156,7.167 0.938,7.438 0.781,0.271 10 false J8*1, J14*2 1.917,6.073 3.344,6.625 1.427,0.552 10 false Outer Rear View Mirror Sub-assembly LH 0.302,6.083 1.531,6.615 1.229,0.531 10 false Side Turn Signal Light Assembly LH 3.406,5.333 3.771,5.542 0.365,0.208 10 false B 3.417,5.708 3.781,5.917 0.365,0.208 10 false E 3.604,5.323 4.375,5.552 0.771,0.229 10 false 10*1, 4*2 3.615,5.708 4.469,5.938 0.854,0.229 10 false 11*1, 12*2 2.875,7.635 4.615,7.979 1.74,0.344 10 false Rear Turn Signal Light LH 2.719,8.198 4.75,8.583 2.031,0.385 10 false Rear Combination Light Socket and Wire Sub-assembly LH 2.729,8.031 3.094,8.24 0.365,0.208 10 false N13 4.646,7.542 5.01,7.75 0.365,0.208 10 false TRN 4.823,7.781 5.188,7.99 0.365,0.208 10 false E 5.021,7.542 5.385,7.75 0.365,0.208 10 false 3 5.031,7.781 5.396,7.99 0.365,0.208 10 false 4 0.083,7.833 2.667,8.167 2.583,0.333 10 false *1: w/o Panoramic View Monitor System 0.083,8.167 2.656,8.448 2.573,0.281 10 false *2: w/ Panoramic View Monitor System 4.698,1.344 5.313,1.573 0.615,0.229 10 false *3 4.635,5.302 5.25,5.531 0.615,0.229 10 false *3

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the bulbs for this system before performing the following procedure.

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Clear DTCs
50002 122

b.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Proceed to
DTC B1507 or B1508 output does not occur
DTC B1507 or B1508 is output



DTC B1507 or B1508 output does not occur

DTC B1507 or B1508 is output

2.CONFIRM MALFUNCTIONING LIGHT
2.CONFIRM MALFUNCTIONING LIGHT
a.

Check the malfunctioning turn signal light.


Result:
Proceed to
No right turn signal lights turn on
No left turn signal lights turn on
One of the right turn signal lights does not turn on
One of the left turn signal lights does not turn on



No right turn signal lights turn on

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH)

No left turn signal lights turn on

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH)

One of the right turn signal lights does not turn on

5.CONFIRM MALFUNCTIONING LIGHT (RH SIDE)

One of the left turn signal lights does not turn on

11.CONFIRM MALFUNCTIONING LIGHT (LH SIDE)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH)

*1: w/ Side Turn Signal Light

*2: w/o Panoramic View Monitor System

*3: w/ Panoramic View Monitor System


a.

Disconnect the G17 combination meter assembly connector.


b.

Disconnect the M19 rear combination light socket wire sub-assembly RH connector.


c.

Disconnect the A42 front turn signal light RH connector.


d.

Disconnect the I8*2 or I14*3 outer rear view mirror sub-assembly RH connector.*1


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-7 (LR) - M19-3 (TRN) Always Below 1 Ω
G17-7 (LR) or M19-3 (TRN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH)

*1: w/ Side Turn Signal Light

*2: w/o Panoramic View Monitor System

*3: w/ Panoramic View Monitor System


a.

Disconnect the G17 combination meter assembly connector.


b.

Disconnect the N13 rear combination light socket wire sub-assembly LH connector.


c.

Disconnect the A16 front turn signal light LH connector.


d.

Disconnect the J8*2 or J14*3 outer rear view mirror sub-assembly LH connector.*1


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-13 (LL) - N13-3 (TRN) Always Below 1 Ω
G17-13 (LL) or N13-3 (TRN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CONFIRM MALFUNCTIONING LIGHT (RH SIDE)
a.

Check the malfunctioning turn signal light.


Result:
Result Proceed to
Front turn signal light does not illuminate A
Side turn signal light does not illuminate (w/ Side Turn Signal Light) B
Rear turn signal light do not illuminate C



A

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT TURN SIGNAL LIGHT RH AND BODY GROUND)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH AND BODY GROUND)

C

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH AND BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT TURN SIGNAL LIGHT RH AND BODY GROUND)

*1: w/ Side Turn Signal Light

*2: w/o Panoramic View Monitor System

*3: w/ Panoramic View Monitor System


a.

Disconnect the G17 combination meter assembly connector.


b.

Disconnect the A42 front turn signal light RH connector.


c.

Disconnect the I8*2 or I14*3 outer rear view mirror sub-assembly RH connector.*1


d.

Disconnect the M19 rear combination light socket wire sub-assembly RH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-7 (LR) - A42-2 (B) Always Below 1 Ω
A42-1 (E) - Body ground
G17-7 (LR) or A42-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH AND BODY GROUND)

*1: w/ Side Turn Signal Light

*2: w/o Panoramic View Monitor System

*3: w/ Panoramic View Monitor System


a.

Disconnect the G17 combination meter assembly connector.


b.

Disconnect the I8*2 or I14*3 outer rear view mirror sub-assembly RH connector.*1


c.

Disconnect the A42 front turn signal light RH connector.


d.

Disconnect the M19 rear combination light socket wire sub-assembly RH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Panoramic View Monitor System
Tester Connection Condition Specified Condition
G17-7 (LR) - I8-10 (B) Always Below 1 Ω
I8-11 (E) - Body ground
G17-7 (LR) or I8-10 (B) - Body ground Always 10 kΩ or higher

w/ Panoramic View Monitor System
Tester Connection Condition Specified Condition
G17-7 (LR) - I14-4 (B) Always Below 1 Ω
I14-12 (E) - Body ground
G17-7 (LR) or I14-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Remove the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
Light comes on
Light not comes on



Light comes on

Light not comes on

10.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH AND BODY GROUND)

*1: w/ Side Turn Signal Light

*2: w/o Panoramic View Monitor System

*3: w/ Panoramic View Monitor System


a.

Disconnect the G17 combination meter assembly connector.


b.

Disconnect the M19 rear combination light socket wire sub-assembly RH connector.


c.

Disconnect the A42 front turn signal light RH connector.


d.

Disconnect the I8*2 or I14*3 outer rear view mirror sub-assembly RH connector.*1


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-7 (LR) - M19-3 (TRN) Always Below 1 Ω
M19-4 (E) - Body ground
G17-7 (LR) or M19-3 (TRN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT SOCKET WIRE SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
a.

Remove the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Inspect the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

11.CONFIRM MALFUNCTIONING LIGHT (LH SIDE)
a.

Check the malfunctioning turn signal light.


Result:
Result Proceed to
Front turn signal lights does not illuminates A
Side turn signal lights does not illuminates (w/ Side Turn Signal Light) B
Rear turn signal lights does not illuminates C



A

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT TURN SIGNAL LIGHT LH AND BODY GROUND)

B

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH AND BODY GROUND)

C

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH AND BODY GROUND)
12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT TURN SIGNAL LIGHT LH AND BODY GROUND)

*1: w/ Side Turn Signal Light

*2: w/o Panoramic View Monitor System

*3: w/ Panoramic View Monitor System


a.

Disconnect the G17 combination meter assembly connector.


b.

Disconnect the A16 front turn signal light LH connector.


c.

Disconnect the J8*2 or J14*3 outer rear view mirror sub-assembly LH connector.*1


d.

Disconnect the N13 rear combination light socket wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-13 (LL) - A16-2 (B) Always Below 1 Ω
A16-1 (E) - Body ground
G17-13 (LL) or A16-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH AND BODY GROUND)

*1: w/o Panoramic View Monitor System

*2: w/ Panoramic View Monitor System


a.

Disconnect the G17 combination meter assembly connector.


b.

Disconnect the J8*1 or J14*2 outer rear view mirror sub-assembly LH connector.


c.

Disconnect the A16 front turn signal light LH connector.


d.

Disconnect the N13 rear combination light socket wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-13 (LL) - J8-10 (B) Always Below 1 Ω
J8-11 (E) - Body ground
G17-13 (LL) or J8-10 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Remove the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
Light comes on
Light not comes on



Light comes on

Light not comes on

16.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH AND BODY GROUND)

*1: w/ Side Turn Signal Light

*2: w/o Panoramic View Monitor System

*3: w/ Panoramic View Monitor System


a.

Disconnect the G17 combination meter assembly connector.


b.

Disconnect the N13 rear combination light socket wire sub-assembly LH connector.


c.

Disconnect the A16 front turn signal light LH connector.


d.

Disconnect the J8*2 or J14*3 outer rear view mirror sub-assembly LH connector.*1


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-13 (LL) - N13-3 (TRN) Always Below 1 Ω
N13-4 (E) - Body ground
G17-13 (LL) or N13-3 (TRN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT SOCKET WIRE SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
a.

Remove the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Inspect the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH