Home › Brake › BRAKE SYSTEM (OTHER) › VACUUM PUMP(When Using the Engine Support Bridge for AD Series Engine)
RM3090E _54 Brake _008768 BRAKE SYSTEM (OTHER) _0256589 VACUUM PUMP(When Using the Engine Support Bridge for AD Series Engine) A

BRAKE SYSTEM (OTHER)  VACUUM PUMP(When Using the Engine Support Bridge for AD Series Engine)  INSTALLATION  


PROCEDURE

Hide 29300 1.INSTALL VACUUM PUMP ASSEMBLY

a.
C128548C02
1.781,1.052 1.781,1.573 false 2.688,1.229 2.688,1.615 false 2.292,1.375 2.292,1.479 2.292,1.479 2.677,1.479 false 1.708,1.625 1.896,1.833 0.188,0.208 10 *1 2.635,1.646 2.844,1.844 0.208,0.198 10 *2
*1 Oil Pipe
*2 O-Ring


Apply engine oil to the oil pipe at the tip of the vacuum pump.


b.

Coat 2 new O-rings with engine oil, and install them to the vacuum pump.


c.
C278628E01
1.583,0.052 1.74,0.25 0.156,0.198 10 A 2.854,0.083 3.01,0.281 0.156,0.198 10 B

Install the vacuum pump so that the coupling teeth of the vacuum pump labeled A and the groove of the camshaft labeled B can engage.


d.
C261794

Install 3 new flange bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.

Connect the 2 vacuum hoses, and slide the clamp to secure it.


Hide 12305 2.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

a.
A297529E01
1.198,1.854 1.354,2.052 0.156,0.198 10 B 2.458,1.771 2.615,1.969 0.156,0.198 10 A

Connect the engine mounting insulator sub-assembly RH with the 2 bolts and 2 nuts.

Torque:
for bolt and nut A : 95 N*m (969 kgf*cm, 70 ft.*lbf)
for nut B : 52 N*m (530 kgf*cm, 38 ft.*lbf)


b.
C354911N01
0.573,1.698 0.698,1.896 0.125,0.198 10 true A 0.833,0.167 0.979,0.365 0.146,0.198 10 true B 0.094,0.198 0.229,0.365 0.135,0.167 10 true C

Tighten the 3 bolts.

HINT:
·

Temporarily tighten bolt A, and then tighten the bolts in the following order: B, C and A.

·

Do not damage the suction tube sub-assembly.



Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.

Connect the 2 clamps to the suction tube sub-assembly.


Hide 3.REMOVE ENGINE SUPPORT BRIDGE

a.

Remove SST from the vehicle body.

NOTICE:

Prevent SST from contacting the vehicle body or windshield.



Hide 4.REMOVE ENGINE HANGER

a.
A297520C02
0.885,0.74 1.031,0.479 1.031,0.479 1.188,0.479 true 2.365,0.417 2.573,0.417 2.573,0.417 2.667,0.771 true 1.208,0.396 1.521,0.552 0.313,0.156 10 false *1 2.198,0.333 2.51,0.49 0.313,0.156 10 false *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Remove the 2 bolts and No.1 and No. 2 engine hangers.


Hide 16470 5.CONNECT RADIATOR RESERVE TANK ASSEMBLY

Hide 51443 6.INSTALL REAR ENGINE UNDER COVER RH

Hide 17801 8.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 9.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 55781E 11.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 12.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

Hide 13.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

Hide 85192 14.INSTALL WINDSHIELD WIPER ARM COVER