Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for RHD) › from 2016.08
RM3090E _54 Brake _008768 BRAKE SYSTEM (OTHER) _0049562 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to release the vacuum from the brake booster before removing the master cylinder from the brake booster.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 85160 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55081E 4.REMOVE COWL VENTILATOR HOUSING SUB-ASSEMBLY

a.
C278611

Disengage the 3 clips and remove the cowl ventilator housing sub-assembly.


Hide 55701J 5.REMOVE COWL TOP PANEL OUTER SUB-ASSEMBLY

a.
C278594

Remove the 13 bolts and cowl top panel outer sub-assembly.


Hide 55735C 6.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

a.
C170048

Remove the 2 nuts and cowl body mounting reinforcement RH.


Hide 7.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 73900 8.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55432B 9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Driver Side Knee Airbag)

Hide 47101A 10.REMOVE BRAKE PEDAL RETURN SPRING

Hide 47264A 11.REMOVE PUSH ROD PIN

Hide 47264D 12.REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS

a.

Loosen the push rod clevis lock nut.


b.

Remove the push rod clevis.


Hide 13.DISCONNECT VACUUM HOSE

a.

Slide the clip and disconnect the vacuum hose from the brake vacuum check valve assembly.


Hide 47374B 14.DISCONNECT NO. 4 BRAKE TUBE CLAMP

a.
C361954

Disconnect the No. 4 brake tube clamp from the body.

NOTICE:

The clamp cannot be reused after it is disconnected from the body.



Hide 47201 15.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 44610 16.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C126454

Remove the 4 nuts.


b.

Pull out the brake booster assembly with the gasket.

NOTICE:

Do not damage the brake lines.



Hide 44785 17.REMOVE BRAKE BOOSTER GASKET

Hide 44730 18.REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY

a.

Remove the brake vacuum check valve assembly from the brake booster assembly.


Hide 44696 19.REMOVE CHECK VALVE GROMMET

a.

Remove the check valve grommet from the brake booster assembly.


Hide 89420H 20.REMOVE VACUUM SENSOR ASSEMBLY (w/ Stop And Start System)

a.

Remove the vacuum sensor assembly from the brake booster assembly.


Hide 44696 21.REMOVE VACUUM SENSOR GROMMET (w/ Stop And Start System)

a.

Remove the vacuum sensor grommet from the brake booster assembly.