Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Manual Seat) › from 2016.08
RM3090E _58 Vehicle Interior _008433 SEAT _0049768 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 71849C 1.INSTALL SEAT ADJUSTER COVER CAP

a.

Install the 2 seat adjuster cover caps to the separate type front seat cushion spring assembly LH.


Hide 72211 2.INSTALL SEAT TRACK ADJUSTING HANDLE

a.

Attach the 2 hooks to install the seat track adjusting handle in the direction indicated by the arrow in the illustration.

B339915


Hide 71537D 3.INSTALL FRONT OUTER SEAT CUSHION EDGE PROTECTOR LH

a.
B339917

Install the front outer seat cushion edge protector LH in the direction indicated by the arrow in the illustration.


Hide 71538B 4.INSTALL FRONT INNER SEAT CUSHION EDGE PROTECTOR LH

HINT:

Use the same procedure described for the front outer seat cushion edge protector LH.


Hide 71874 5.INSTALL FRONT LOWER SEAT CUSHION SHIELD LH

a.

Attach the clip to install the front lower seat cushion shield LH.


b.
B339916

Attach the hook in the direction indicated by the arrow in the illustration.


c.

Install the screw.


Hide 71873 6.INSTALL FRONT LOWER SEAT CUSHION SHIELD RH

HINT:

Use the same procedure described for the front lower seat cushion shield LH.


Hide 71537C 7.INSTALL FRONT OUTER SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side)

a.
B339918

Install the front outer seat cushion edge protector RH in the direction indicated by the arrow in the illustration.


Hide 71538A 8.INSTALL FRONT INNER SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side)

HINT:

Use the same procedure described for the front outer seat cushion edge protector RH.


Hide 89952 9.INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side, w/ Occupant Classification System)

Hide 82191 10.INSTALL FRONT SEAT WIRE RH (for Front Passenger Side, w/ Occupant Classification System)

a.
B384524

Attach the 4 clamps to install the front seat wire RH.


b.

Connect the 4 connectors.


c.

Attach the claw to connect the connector.


Hide 73240 11.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

a.
B338233

Install the front seat inner belt assembly LH with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Attach the 2 clamps.


c.

for Type A:

i.
B338234C01
1.667,0.802 2.083,0.25 true 1.198,0.51 1.5,0.25 true 2.167,0.75 3,0.75 true 1.521,0.167 1.833,0.323 0.313,0.156 10 *1 3.042,0.677 3.354,0.833 0.313,0.156 10 *2 2.073,0.146 2.385,0.302 0.313,0.156 10 *1
*1 Wire Harness Clamp
*2 Connector Clamp


Attach the 2 wire harness clamps and connector clamp.



d.

for Type B:

i.
B341338

Attach the wire harness clamp.


ii.
B341337C01
1.583,0.917 0.667,1.25 0.667,1.25 0.5,1.25 true 1.25,0.75 0.667,0.75 true 2.667,0.583 2.5,0.583 2.5,0.583 1.917,0.75 true 2.698,0.917 2.115,0.917 true 0.521,0.677 0.833,0.833 0.313,0.156 10 *1 2.698,0.5 3.01,0.656 0.313,0.156 10 *2 0.333,1.167 0.646,1.323 0.313,0.156 10 *1 2.74,0.844 3.052,1 0.313,0.156 10 *1
*1 Wire Harness Clamp
*2 Connector Clamp


Attach the 3 wire harness clamps and connector clamp.



Hide 73230 12.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

a.

for Type A:

i.
B387953

Install the front seat inner belt assembly RH with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


ii.

Attach the clamp.


iii.
B339912C01
0.5,0.583 1.333,0.583 true 1.688,0.552 2,0.25 true 2.25,1.167 3,1.167 true 2.229,0.792 3,0.792 true 2.031,0.167 2.344,0.323 0.313,0.156 10 *1 0.354,0.51 0.667,0.667 0.313,0.156 10 *2 3.021,0.708 3.333,0.865 0.313,0.156 10 *1 3.021,1.094 3.333,1.25 0.313,0.156 10 *1
*1 Wire Harness Clamp
*2 Connector Clamp


Attach the 3 wire harness clamps and connector clamp.



b.

for Type B:

i.
B384523

Install the front seat inner belt assembly RH with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


ii.

Attach the clamp.


iii.
B380450

Connect the connector.



Hide 73905 13.INSTALL FRONT SEAT AIRBAG SUB-ASSEMBLY RH (for Front Passenger Side, w/ Occupant Classification System)

Hide 89178A 14.INSTALL SEAT POSITION AIRBAG SENSOR (w/ Occupant Classification System)

Hide 87510L 15.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71072S 16.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

a.

Set the separate type front seat cushion cover in place.


b.

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 21 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



HINT:

Install the hog rings at the cutouts if they are there.


B338259C02
0.948,3.542 0.885,3.083 true 1.813,3.208 1.625,2.771 false 4.333,3.292 4.74,3.063 true 5.292,2.625 4.979,2.948 false 1.49,2.656 1.802,2.813 0.313,0.156 10 *1 0.885,3.542 1.198,3.698 0.313,0.156 10 *a 5.323,2.521 5.635,2.677 0.313,0.156 10 *1 4.188,3.229 4.5,3.385 0.313,0.156 10 *a
*1 Hog Ring Pliers - -
*a Cutout - -



Hide 17.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

for Driver Side:

i.

Attach the 12 hooks to install the separate type front seat cushion cover with pad.

B338248



b.

for Front Passenger Side:

i.

Attach the 11 hooks to install the separate type front seat cushion cover with pad.

B342808


ii.
B338247

w/ Occupant Detection Sensor:

Attach the clamp and connect the connector.



c.

w/ Seat Heater System:

i.
B339911C01
0.396,1.052 0.969,1.052 true 0.417,1.458 0.969,1.458 true 1.844,0.51 2.813,0.51 true 0.385,0.667 1.188,0.667 true 1.844,0.354 2.813,0.354 true 2.844,0.271 3.156,0.427 0.313,0.156 10 *2 0.26,1.375 0.573,1.531 0.313,0.156 10 *1 0.25,0.969 0.563,1.125 0.313,0.156 10 *1 0.229,0.583 0.542,0.74 0.313,0.156 10 *1 2.865,0.438 3.177,0.594 0.313,0.156 10 *1
*1 Wire Harness Clamp
*2 Connector Clamp


Attach the connector clamp and 4 wire harness clamps to connect the wire harness of the front seat cushion heater.



Hide 73920A 18.INSTALL FRONT SEAT AIRBAG ASSEMBLY LH (w/ Front Seat Side Airbag)

Hide 79977A 19.INSTALL SEATBACK FELT

a.

Install the seatback felt to the separate type front seatback spring assembly LH.


Hide 71552S 20.INSTALL SEPARATE TYPE FRONT SEATBACK PAD

a.

Install the separate type front seatback pad to the separate type front seatback spring assembly LH.


Hide 87510N 21.INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71074S 22.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.

Set the separate type front seatback cover in place.


b.
B338258C01
0.396,3.917 0.635,3.188 true 1.615,3.885 2.031,3.469 false 2.021,3.333 2.333,3.49 0.313,0.156 10 *1 0.313,3.906 0.625,4.063 0.313,0.156 10 *a
*1 Hog Ring Pliers
*a Cutout


Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 8 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



HINT:

Install the hog rings at the cutouts if they are there.



c.

w/ Front Seat Side Airbag:

i.

Pass the separate type front seatback cover bracket through the separate type front seatback pad.


ii.

for Dual Type:

Install the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


iii.

for Single Type:

Install the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)



d.

for Sports Seat Type:

Close the 2 fasteners.


e.
B340871

Pull the straps to tighten them and confirm that there is a protrusion visible on each side.


f.
B447867C03
1.458,4.302 1.604,3.813 false 1.375,4.323 1.688,4.479 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, connect the straps of the separate type front seatback cover to the separate type front seatback frame sub-assembly LH with 3 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the straps of the separate type front seatback cover.




g.
B447883

Attach the 3 hooks.


Hide 71931 23.INSTALL FRONT SEAT HEADREST SUPPORT

a.

Attach the 4 claws to install the 2 front seat headrest supports.


Hide 24.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.
B338236

Install the separate type front seatback assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
B338235

Attach the 2 hooks.


c.

w/ Front Seat Side Airbag:

i.
B340391C01
2.25,0.917 2.833,0.917 true 2.875,0.823 3.188,0.979 0.313,0.156 10 *1
*1 Fastener


Attach the fastener to connect the wire harness of the front seat side airbag.


ii.
B338249C01
2.396,0.646 2.51,0.948 true 1.99,2.021 2.26,1.719 true 1.833,0.969 2.031,0.823 true 2.115,1.313 2.302,1.313 true 2.458,0.417 2.625,0.323 true 2.625,0.229 2.938,0.385 0.313,0.156 10 *2 2.479,0.948 2.792,1.104 0.313,0.156 10 *1 1.844,1.979 2.156,2.135 0.313,0.156 10 *1 1.969,1.229 2.281,1.385 0.313,0.156 10 *1 1.729,0.958 2.042,1.115 0.313,0.156 10 *1
*1 Wire Harness Clamp
*2 Connector Clamp


Attach the 4 wire harness clamps and connector clamp to connect the wire harness of the front seat side airbag.



d.
B340392

w/ Seat Heater System:

i.

Attach the wire harness clamp and connector clamp.


ii.

Connect the connector.



e.

Connect the rubber band.


Hide 71862 25.INSTALL FRONT INNER SEAT CUSHION SHIELD LH

a.
B339919C01
1.854,0.333 1.885,0.292 false
V100135

First
V100136

Second


Attach the 3 guides and 2 claws to install the front inner seat cushion shield LH as indicated by the arrows in the order shown in the illustration.


Hide 71861 26.INSTALL FRONT INNER SEAT CUSHION SHIELD RH (for Front Passenger Side)

a.
B339920C01
1.833,0.417 1.833,0.354 false
V100135

First
V100136

Second


Attach the 3 guides and 2 claws to install the front inner seat cushion shield RH as indicated by the arrows in the order shown in the illustration.


Hide 71812D 27.INSTALL FRONT SEAT CUSHION SHIELD LH

a.
B339921C01
1.292,1.75 1.313,1.76 false
V100135

First
V100136

Second


Attach the 3 guides and claw to install the front seat cushion shield LH as indicated by the arrows in the order shown in the illustration.


b.
B338229

Attach the claw and 2 clips.


Hide 72495 28.INSTALL VERTICAL ADJUSTING HANDLE LH

a.

Install the vertical adjusting handle LH with the screw.


Hide 72526A 29.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.

Attach the claw to install the reclining adjuster release handle LH.