When a rear door is opened and closed (the rear door courtesy light switch turns on and off) with the ignition switch ON, or when a rear door is opened and closed (the rear door courtesy light switch turns on and off) and then the ignition switch is turned to ON, the rear seat belt warning light in the telltale light assembly turns on to inform the driver of condition of the rear seat belts. If a rear seat belt is fastened or unfastened, the warning light changes to indicate the current condition of the rear seat belts.
Only for vehicles with a rear seat belt indicator.
The seat belt warning system uses a CAN communication system. Inspect the communication function by following How to Proceed with troubleshooting.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Door Courtesy SW | Rear door RH courtesy light switch signal | ON/OFF | ON: Rear door RH open
OFF: Rear door RH closed |
- |
| RL Door Courtesy SW | Rear door LH courtesy light switch signal | ON/OFF | ON: Rear door LH open
OFF: Rear door LH closed |
- |
| Tester Display |
|---|
| RR Door Courtesy SW |
| RL Door Courtesy SW |
| Result | Proceed to |
|---|---|
| ON or OFF is displayed on the GTS screen according to the rear door courtesy light switch condition | A |
| ON or OFF is not displayed normally on the GTS screen according to the rear door courtesy light switch condition | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 2nd-Row Seatbelt Buckle (R) | Rear seat belt buckle RH signal | ON/OFF | ON: Rear seat belt RH fastened
OFF: Rear seat belt RH unfastened |
- |
| 2nd-Row Seatbelt Buckle (L) | Rear seat belt buckle LH signal | ON/OFF | ON: Rear seat belt LH fastened
OFF: Rear seat belt LH unfastened |
- |
| 2nd-Row Seatbelt Buckle (C) | Rear center seat belt buckle signal | ON/OFF | ON: Rear center seat belt fastened
OFF: Rear seat center belt unfastened |
- |
| Tester Display |
|---|
| 2nd-Row Seatbelt Buckle (R) |
| 2nd-Row Seatbelt Buckle (L) |
| 2nd-Row Seatbelt Buckle (C) |
| Result | Proceed to |
|---|---|
| ON or OFF is displayed on the GTS screen according to the rear seat belt condition | A |
| ON or OFF is not displayed normally on the GTS screen according to the rear seat belt condition | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Seat Belt | Rear seat belt warning light | ON/OFF | - |
| Tester Display |
|---|
| Rear Seat Belt |
The rear seat belt warning light on the combination meter assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the combination meter assembly with a new one.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the rear seat belt warning light.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT>INSPECTION
| Proceed to |
|---|
| The rear seat belt warning light operates normally. |
| The rear seat belt warning light operates abnormally. |
The rear seat belt warning light operates normally.
The rear seat belt warning light operates abnormally.
Remove the telltale light assembly.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT>REMOVAL
Inspect the telltale light assembly.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G43 telltale light assembly connector.
Disconnect the G16 combination meter assembly meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G43-22 (RLID) - G16-14 (RLMT) | Always | Below 1 Ω |
| G43-23 (RCID) - G16-19 (RCMT) | ||
| G43-24 (RRID) - G16-3 (RRMT) | ||
| G43-22 (RLID) - Body ground | Always | 10 kΩ or higher |
| G43-23 (RCID) - Body ground | ||
| G43-24 (RRID) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LH, RH:
Remove the rear seat inner belt assembly.
Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>REMOVAL
for Center:
Remove the rear center lap type seat belt assembly RH.
Click hereVehicle Interior>SEAT BELT>REAR CENTER SEAT OUTER BELT ASSEMBLY>REMOVAL
for LH, RH:
Inspect the rear seat inner belt assembly.
Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>INSPECTION
for Center:
Inspect the rear center lap type seat belt assembly RH.
Click hereVehicle Interior>SEAT BELT>REAR CENTER SEAT OUTER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG (for LH) |
| NG (for Center) |
| NG (for RH) |
OK
NG (for LH)
NG (for Center)
NG (for RH)
Disconnect the M12*1, M13*2 or M14*3 rear seat inner belt assembly connector.
*1: for RH
*2: for Center
*3: for LH
Disconnect the G16 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M14-1 - G16-24 (RLSB) | Always | Below 1 Ω |
| M14-2 - Body ground | ||
| M14-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M13-1 - G16-25 (RCSB) | Always | Below 1 Ω |
| M13-2 - Body ground | ||
| M13-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M12-1 - G16-26 (RRSB) | Always | Below 1 Ω |
| M12-2 - Body ground | ||
| M12-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG