Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2016.08
RM3090E _58 Vehicle Interior _008433 SEAT _0062871 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Position is not Memorized  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives seat memory switch signals from the seat memory switch via CAN communication. If the seat memory SET switch is being pressed when one of the M1 or M2 switches is pressed, or if one of the M1 or M2 switches is pressed within 3 seconds of pressing the seat memory SET switch, the main body ECU (multiplex network body ECU) sends a memory request signal to the position control ECU and switch assembly. After receiving the request signal, the position control ECU and switch assembly memorizes the location data of each motor.

WIRING DIAGRAM

for LHD:
B342200E01
5.167,2.719 6.583,2.938 1.417,0.219 10 false Seat Memory Switch 5.156,2.542 5.615,2.74 0.458,0.198 10 false J13 5.365,1.99 5.521,2.188 0.156,0.198 10 false E 5.365,0.917 5.823,1.115 0.458,0.198 10 false MRY 5.354,1.313 5.667,1.51 0.313,0.198 10 false M2 5.365,1.698 5.677,1.896 0.313,0.198 10 false M1 4.188,1.708 4.5,1.906 0.313,0.198 10 false M1 4.188,1.323 4.5,1.521 0.313,0.198 10 false M2 4.156,0.927 4.469,1.125 0.313,0.198 10 false MM 5.156,0.813 5.313,1.01 0.156,0.198 10 false 2 5.167,1.208 5.323,1.406 0.156,0.198 10 false 4 5.167,1.563 5.323,1.76 0.156,0.198 10 false 3 5.156,1.885 5.313,2.083 0.156,0.198 10 false 1 4.49,1.583 4.802,1.781 0.313,0.198 10 false 25 4.49,1.208 4.802,1.406 0.313,0.198 10 false 23 4.49,0.823 4.802,1.021 0.313,0.198 10 false 26 0.781,3.427 4.448,3.625 3.667,0.198 10 false : CAN Communication Line 3.042,2.635 4.677,3.104 1.635,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 3.042,2.427 3.5,2.625 0.458,0.198 10 false G79 0.656,2.458 2.01,2.865 1.354,0.406 10 false Position Control ECU and Switch Assembly

for RHD:
B342200E02
5.167,2.719 6.583,2.938 1.417,0.219 10 false Seat Memory Switch 5.156,2.542 5.615,2.74 0.458,0.198 10 false I16 5.365,1.99 5.521,2.188 0.156,0.198 10 false E 5.365,0.917 5.823,1.115 0.458,0.198 10 false MRY 5.354,1.313 5.667,1.51 0.313,0.198 10 false M2 5.365,1.698 5.677,1.896 0.313,0.198 10 false M1 4.188,1.708 4.5,1.906 0.313,0.198 10 false M1 4.188,1.323 4.5,1.521 0.313,0.198 10 false M2 4.156,0.927 4.469,1.125 0.313,0.198 10 false MM 5.156,0.813 5.313,1.01 0.156,0.198 10 false 2 5.167,1.208 5.323,1.406 0.156,0.198 10 false 4 5.167,1.563 5.323,1.76 0.156,0.198 10 false 3 5.156,1.885 5.313,2.083 0.156,0.198 10 false 1 4.49,1.583 4.802,1.781 0.313,0.198 10 false 25 4.49,1.208 4.802,1.406 0.313,0.198 10 false 23 4.49,0.823 4.802,1.021 0.313,0.198 10 false 26 0.781,3.427 4.448,3.625 3.667,0.198 10 false : CAN Communication Line 3.042,2.635 4.677,3.104 1.635,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 3.042,2.427 3.5,2.625 0.458,0.198 10 false G79 0.656,2.458 2.01,2.865 1.354,0.406 10 false Position Control ECU and Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL SYSTEM
a.

Check that each function of the power seat operates normally by using the power seat switch.

OK:

Each function of the power seat operates normally using the power seat switch.


Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (SEAT MEMORY SWITCH)

NG

2.READ VALUE USING GTS (SEAT MEMORY SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
M1 Switch M1 switch ON or OFF ON: M1 switch on
OFF: M1 switch off
-
M2 Switch M2 switch ON or OFF ON: M2 switch on
OFF: M2 switch off
-
SET Switch SET switch ON or OFF ON: SET switch on
OFF: SET switch off
-
Body Electrical > Main Body > Data List
Tester Display
M1 Switch
M2 Switch
SET Switch
50003 123 213,214,216
OK:

ON or OFF is displayed on the GTS according to the table above.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (BUZZER)

NG

8.INSPECT SEAT MEMORY SWITCH
3.PERFORM ACTIVE TEST USING GTS (BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Buzzer operation OFF/ON -
Body Electrical > Driver Seat > Active Test
Tester Display
Buzzer
50004 162 5
OK:

Buzzer sounds normally.



Result:
Proceed to
OK
NG



OK

4.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

4.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Result:
Proceed to
NEXT



NEXT

5.CHECK SEAT POSITION MEMORY FUNCTION
5.CHECK SEAT POSITION MEMORY FUNCTION
a.

Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.




Result:
Result Proceed to
Seat position memory function operates normally A
Seat position memory function does not operate normally B



A

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU WAS DEFECTIVE])

B

6.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
6.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Replace the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK SEAT POSITION MEMORY FUNCTION
7.CHECK SEAT POSITION MEMORY FUNCTION
a.

Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.




Result:
Result Proceed to
Seat position memory function operates normally A
Seat position memory function does not operate normally B



A

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

B

8.INSPECT SEAT MEMORY SWITCH
a.

Remove the seat memory switch.

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL


b.

Inspect the seat memory switch.

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - SEAT MEMORY SWITCH)

NG

REPLACE SEAT MEMORY SWITCH

9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - SEAT MEMORY SWITCH)
a.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the J13*1 or I16*2 seat memory switch connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
G79-23 (M2) - J13-4 (M2) Always Below 1 Ω
G79-25 (M1) - J13-3 (M1) Always Below 1 Ω
G79-26 (MM) - J13-2 (MRY) Always Below 1 Ω
G79-23 (M2) - Body ground Always 10 kΩ or higher
G79-25 (M1) - Body ground Always 10 kΩ or higher
G79-26 (MM) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
G79-23 (M2) - I16-4 (M2) Always Below 1 Ω
G79-25 (M1) - I16-3 (M1) Always Below 1 Ω
G79-26 (MM) - I16-2 (MRY) Always Below 1 Ω
G79-23 (M2) - Body ground Always 10 kΩ or higher
G79-25 (M1) - Body ground Always 10 kΩ or higher
G79-26 (MM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR