Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › from 2016.08
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) or more for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High When all of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.4 mph) or more.

(b) The engine speed is 1000 rpm or more.

(c) The STA signal is on.


·

Park/Neutral position switch assembly (for CVT Models)

·

Ignition switch assembly (w/o Entry and Start System)

·

STA signal circuit

·

Engine stop and start ECU

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A231469E13
1.229,1.979 1.604,2.156 0.375,0.177 10 Idling 0.396,2.25 1.604,2.573 1.208,0.323 10 Ignition Switch ON 1.063,0.813 1.635,1.021 0.573,0.208 10 24 km/h 2.396,2.854 3.094,3.375 0.698,0.521 10 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 20 seconds or more 2,2.333 2.635,2.677 0.635,0.344 10 [A] 2.583,2.125 3.271,2.375 0.688,0.25 10 [B] 4.031,0.458 4.5,0.823 0.469,0.365 10 [C] 4.906,3.344 5.344,3.563 0.438,0.219 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds or more [B].

8.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0617.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A347030E03
0.083,0.083 2.188,0.427 2.104,0.344 12 false for CVT Models: 0.271,2.042 0.667,2.24 0.396,0.198 10 false A66 0.26,2.188 2.198,2.385 1.938,0.198 10 false Engine Stop and Start ECU 1.323,0.667 1.719,0.865 0.396,0.198 10 false NE 1.177,1.063 1.573,1.26 0.396,0.198 10 false STA2 1.281,1.438 1.677,1.635 0.396,0.198 10 false CLL 1.25,1.74 1.646,1.938 0.396,0.198 10 false STA 1.604,0.573 2,0.771 0.396,0.198 10 false 10 1.625,0.927 2.021,1.125 0.396,0.198 10 false 23 1.635,1.302 2.031,1.5 0.396,0.198 10 false 17 1.635,1.625 2.031,1.823 0.396,0.198 10 false 21 6.281,1.719 6.677,1.917 0.396,0.198 10 false A62 6.271,1.875 6.667,2.073 0.396,0.198 10 false ECM 6.031,0.667 6.427,0.865 0.396,0.198 10 false NEO 6.031,1.052 6.427,1.25 0.396,0.198 10 false STA 6.031,1.438 6.427,1.635 0.396,0.198 10 false NSW 5.74,0.552 6.135,0.75 0.396,0.198 10 false 30 5.75,0.927 6.146,1.125 0.396,0.198 10 false 29 5.75,1.313 6.146,1.51 0.396,0.198 10 false 23 0.031,3.958 0.427,4.156 0.396,0.198 10 false G82 0.031,4.135 2.948,4.396 2.917,0.26 10 false Certification ECU (Smart Key ECU Assembly)*1 1.323,2.688 1.719,2.885 0.396,0.198 10 false NE 1.167,3.208 1.563,3.406 0.396,0.198 10 false STAR 1.25,3.677 1.646,3.875 0.396,0.198 10 false STA 1.635,2.573 2.031,2.771 0.396,0.198 10 false 16 1.667,3.063 2.063,3.26 0.396,0.198 10 false 5 1.667,3.552 2.063,3.75 0.396,0.198 10 false 7 3.563,3.979 3.958,4.177 0.396,0.198 10 false B36 3.563,4.156 5.375,4.625 1.813,0.469 10 false Park/Neutral Position Switch Assembly 0.688,5.052 1.083,5.25 0.396,0.198 10 false AM2 1.302,5.354 3.24,5.552 1.938,0.198 10 false Ignition Switch Assembly*2 1.292,5.198 1.688,5.396 0.396,0.198 10 false G4 1.625,4.771 2.021,4.969 0.396,0.198 10 false AM2 2.229,4.771 2.625,4.969 0.396,0.198 10 false ST2 1.427,4.76 1.823,4.958 0.396,0.198 10 false 4 2.594,4.75 2.99,4.948 0.396,0.198 10 false 2 4.198,6.896 4.594,7.094 0.396,0.198 10 false B87 4.198,7.052 5.406,7.396 1.208,0.344 10 false Starter Assembly 2.563,6.531 3.333,6.729 0.771,0.198 10 false ST NO.1 2.563,7.719 3.417,8 0.854,0.281 10 false ST NO.2 1.188,7.167 2.042,7.448 0.854,0.281 10 false ST NO.2 1.208,6.042 2.063,6.323 0.854,0.281 10 false ST 0.396,7.479 1.25,7.76 0.854,0.281 10 false FL MAIN 0.542,8.125 1.396,8.406 0.854,0.281 10 false Battery 4.479,7.958 6.917,8.302 2.438,0.344 10 false *1: w/ Entry and Start System 4.479,8.302 6.917,8.646 2.438,0.344 10 false *2: w/o Entry and Start System 2.406,2.635 2.802,2.833 0.396,0.198 10 false *1 2.396,3.094 2.792,3.292 0.396,0.198 10 false *1 2.385,3.594 2.781,3.792 0.396,0.198 10 false *1 2.76,4.781 3.156,4.979 0.396,0.198 10 false *2 4.823,3.563 5.219,3.76 0.396,0.198 10 false 4 3.719,3.563 4.115,3.76 0.396,0.198 10 false 9 4.594,3.573 4.99,3.771 0.396,0.198 10 false B 3.927,3.573 4.323,3.771 0.396,0.198 10 false L 3.188,5.76 3.583,5.958 0.396,0.198 10 false 3 3.208,6.885 3.604,7.083 0.396,0.198 10 false 3 3.188,6.135 3.583,6.333 0.396,0.198 10 false 2 3.198,7.292 3.594,7.49 0.396,0.198 10 false 2 2.375,5.76 2.771,5.958 0.396,0.198 10 false 5 2.385,6.885 2.781,7.083 0.396,0.198 10 false 5 2.375,6.135 2.771,6.333 0.396,0.198 10 false 1 2.375,7.292 2.771,7.49 0.396,0.198 10 false 1 4.104,5.719 4.5,5.917 0.396,0.198 10 false 2 4.104,6.469 4.5,6.667 0.396,0.198 10 false 1 4.302,6.615 4.698,6.813 0.396,0.198 10 false SL2 4.302,5.885 4.698,6.083 0.396,0.198 10 false SL1

A375790E02
0.063,0.01 5.198,0.25 5.135,0.24 12 false for Manual Transaxle Models: 6.042,0.656 6.5,0.854 0.458,0.198 10 false NEO 6.031,1.125 6.49,1.323 0.458,0.198 10 false STA 6.052,1.719 6.51,1.917 0.458,0.198 10 false A62 6.427,1.719 6.885,1.917 0.458,0.198 10 false ECM 5.802,0.583 6.115,0.781 0.313,0.198 10 false 30 5.802,1.01 6.115,1.208 0.313,0.198 10 false 29 1.323,0.688 1.635,0.885 0.313,0.198 10 false NE 1.615,0.594 1.927,0.792 0.313,0.198 10 false 10 1.281,1.115 1.74,1.313 0.458,0.198 10 false CLL 1.635,1.021 1.948,1.219 0.313,0.198 10 false 17 1.25,1.552 1.708,1.75 0.458,0.198 10 false STA 1.625,1.448 1.938,1.646 0.313,0.198 10 false 21 0.469,2.01 0.927,2.208 0.458,0.198 10 false A66 0.458,2.188 4.281,2.385 3.823,0.198 10 false Engine Stop and Start ECU 1.323,2.708 1.635,2.906 0.313,0.198 10 false NE 1.156,3.667 1.771,3.865 0.615,0.198 10 false STAR 1.25,3.198 1.708,3.396 0.458,0.198 10 false STA 1.615,2.615 1.927,2.813 0.313,0.198 10 false 16 1.656,3.052 1.813,3.25 0.156,0.198 10 false 7 1.656,3.542 1.813,3.74 0.156,0.198 10 false 5 3.906,3.979 4.219,4.177 0.313,0.198 10 false A4 3.896,4.156 5.792,4.385 1.896,0.229 10 false Clutch Start Switch Assembly 5.115,3.573 5.271,3.771 0.156,0.198 10 false 1 4.073,3.573 4.229,3.771 0.156,0.198 10 false 2 0.073,4.01 0.531,4.208 0.458,0.198 10 false G82 0.042,4.198 6.771,4.396 6.729,0.198 10 false Certification ECU (Smart Key ECU Assembly)*1 2.135,2.594 2.448,2.792 0.313,0.198 10 false *1 2.125,3.083 2.438,3.281 0.313,0.198 10 false *1 2.115,3.573 2.427,3.771 0.313,0.198 10 false *1 2.823,4.781 3.135,4.979 0.313,0.198 10 false *2 2.563,4.802 2.719,5 0.156,0.198 10 false 2 2.229,4.781 2.688,4.979 0.458,0.198 10 false ST2 1.625,4.792 2.083,4.99 0.458,0.198 10 false AM2 1.479,4.781 1.635,4.979 0.156,0.198 10 false 4 1.385,5.188 1.698,5.385 0.313,0.198 10 false G4 1.417,5.354 5.396,5.552 3.979,0.198 10 false Ignition Switch Assembly*2 0.698,5.042 1.156,5.24 0.458,0.198 10 false AM2 2.563,6.552 3.635,6.75 1.073,0.198 10 false ST NO.1 0.365,6.365 1.438,6.563 1.073,0.198 10 false FL MAIN 1.354,6.042 1.667,6.24 0.313,0.198 10 false ST 4.979,6.854 5.292,7.052 0.313,0.198 10 false B6 4.25,7.083 4.563,7.281 0.313,0.198 10 false C6 5.281,6.844 5.438,7.042 0.156,0.198 10 false 1 4.344,6.875 4.5,7.073 0.156,0.198 10 false 1 4.26,7.875 6.708,8.073 2.448,0.198 10 false Starter Assembly 0.552,8.104 1.625,8.302 1.073,0.198 10 false Battery 1.771,7.583 3.688,7.802 1.917,0.219 10 false *1: w/ Entry and Start System 1.771,8.031 3.719,8.281 1.948,0.25 10 false *2: w/o Entry and Start System 2.417,5.781 2.573,5.979 0.156,0.198 10 false 5 3.156,5.792 3.313,5.99 0.156,0.198 10 false 3 2.417,6.167 2.573,6.365 0.156,0.198 10 false 1 3.156,6.177 3.313,6.375 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

NOTICE:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF (Starter signal off) A
ON (Starter signal on)
(for CVT Models)
B
ON (Starter signal on)
(for Manual Transaxle Models)
C



A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

7.INSPECT CLUTCH START SWITCH
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT ENGINE STOP AND START ECU

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

3.INSPECT ENGINE STOP AND START ECU
a.

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

A350366C02
3.198,0.771 3.667,1.052 0.469,0.281 3.198,1.708 2.823,2.417 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 2.646,2.438 3.313,2.698 0.667,0.26 10 false STA2 3.302,0.844 3.635,1.042 0.333,0.198 10 false A66
*a Component with harness connected
(Engine Stop and Start ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A66-23 (STA2) - Body ground Vehicle driving (Engine speed of 1000 rpm or more and vehicle speed at 20 km/h (12 mph) or more) 0 to 1.5 V



Result:
Result Proceed to
OK
(w/ Entry and Start System)
A
OK
(w/o Entry and Start System)
B
NG C



A

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (park/neutral position switch assembly - ST NO.1 relay - certification ECU (smart key ECU assembly) - engine stop and start ECU - ECM - ST NO.2 relay).


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read the DTCs.

Result:
Result Proceed to
DTC P0617 is output A
DTC is not output B




A

B

END

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (park/neutral position switch assembly - ST NO.1 relay - engine stop and start ECU - ECM - ST NO.2 relay).


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
7.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result Proceed to
OK
(w/ Entry and Start System)
A
OK
(w/o Entry and Start System)
B
NG C



A

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

B

9.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE CLUTCH START SWITCH

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (clutch start switch assembly - ST NO.1 relay - certification ECU (smart key ECU assembly) - engine stop and start ECU - ECM).


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
9.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (clutch start switch assembly - ST NO.1 relay - engine stop and start ECU - ECM).


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)