Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › from 2016.08
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM J

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).

*1: w/o Entry and Start System

*2: w/ Entry and Start System


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

11.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Result Proceed to
NG
(for CVT models)
A
NG
(for Manual Transaxle Models)
B
OK C



A

3.CHECK HARNESS AND CONNECTOR (ECM - ENGINE STOP AND START ECU - ST NO. 2 RELAY)

B

5.INSPECT CLUTCH START SWITCH ASSEMBLY

C

GO TO STOP AND START SYSTEM (STARTER SIGNAL CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (ECM - ENGINE STOP AND START ECU - ST NO. 2 RELAY)
a.

Disconnect the ECM connector.


b.

Disconnect the engine stop and start ECM connector.


c.

Remove the ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-29 (STA) - A66-23 (STA2) Always Below 1 Ω
A62-29 (STA), A66-23 (STA2) or 2 (ST NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the engine stop and start ECM connector.


c.

Disconnect the park/neutral position switch assembly connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-23 (NSW) - A66-17 (CLL) Always Below 1 Ω
A62-23 (NSW), A66-17 (CLL) or B36-4 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO STOP AND START SYSTEM (STARTER SIGNAL CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECM)

B

8.INSPECT IGNITION SWITCH ASSEMBLY

C

REPLACE CLUTCH START SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECM)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the engine stop and start ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - A4-2 Always Below 1 Ω
G82-5 (STAR) - A66-17 (CLL) Always Below 1 Ω
A66-17 (CLL) - A4-2 Always Below 1 Ω
G82-5 (STAR) or A4-2 - Body ground Always 10 kΩ or higher
G82-5 (STAR) or A66-17 (CLL) - Body ground Always 10 kΩ or higher
A66-17 (CLL) or A4-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST NO.1 RELAY - ECM - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST NO.1 RELAY - ECM - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST NO.1 relay from the No. 2 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Disconnect the engine stop and start ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1 - A62-29 (STA) Always Below 1 Ω
A4-1, 2 (ST NO.1 relay), A62-29 (STA), G82-7 (STA) or A66-21 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO STOP AND START SYSTEM (STARTER SIGNAL CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>3ZR-FAE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECM)

NG

REPLACE IGNITION SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECM)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the engine stop and start ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - A4-2 Always Below 1 Ω
G4-2 (ST2) - A66-17 (CLL) Always Below 1 Ω
A66-17 (CLL) - A4-2 Always Below 1 Ω
G4-2 (ST2) or A4-2 - Body ground Always 10 kΩ or higher
G4-2 (ST2) or A66-17 (CLL) - Body ground Always 10 kΩ or higher
A66-2 (ST2) or A4-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST NO.1 RELAY - ECM - ENGINE STOP AND START ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST NO.1 RELAY - ECM - ENGINE STOP AND START ECM)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST NO.1 relay from the No. 2 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the engine stop and start ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1 - A62-29 (STA) Always Below 1 Ω
A4-1, 2 (ST NO.1 relay), A62-29 (STA) or A66-21 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Result Proceed to
OK A
NG (w/ Stop and Start system) B
NG (w/o Stop and Start system) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO.2 RELAY - ECM)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO.1 RELAY - ECM)