Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) J

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  Starter Signal Circuit  


DESCRIPTION

for CVT:

By using the starter delay circuit, the engine stop and start ECU can activate the ST NO. 2 relay (for starter motor operation) after activating the ST NO. 1 relay (for starter pinion operation) to operate the starter assembly.

for Manual Transaxle:

The engine stop and start ECU can activate the ST NO. 1 relay to operate the starter assembly.

WIRING DIAGRAM

for CVT:


A350621E02
1.958,2.677 4.646,2.917 2.688,0.24 10 false Instrument Panel Junction Block Assembly 3.198,2.24 3.656,2.438 0.458,0.198 10 false IGN 1.792,2.094 2.104,2.292 0.313,0.198 10 false 3B 1.792,1.885 2.104,2.083 0.313,0.198 10 false 14 4.625,2.083 4.938,2.281 0.313,0.198 10 false 3C 4.625,1.885 4.938,2.083 0.313,0.198 10 false 37 4.615,1.427 4.927,1.625 0.313,0.198 10 false 3C 4.625,1.219 4.938,1.417 0.313,0.198 10 false 43 2.646,1.677 4.021,1.875 1.375,0.198 10 false IG1 NO. 1 1.771,1.417 2.083,1.615 0.313,0.198 10 false 3D 1.813,1.219 2.125,1.417 0.313,0.198 10 false 9 1.771,1 2.083,1.198 0.313,0.198 10 false 3A 1.802,0.771 2.115,0.969 0.313,0.198 10 false 1 4.604,0.99 4.917,1.188 0.313,0.198 10 false 3D 4.615,0.792 4.927,0.99 0.313,0.198 10 false 43 3.656,1.135 4.573,1.333 0.917,0.198 10 false EPS-IG 5.719,1 6.177,1.198 0.458,0.198 10 false G87 5.76,0.802 6.073,1 0.313,0.198 10 false 21 6.115,0.99 6.573,1.188 0.458,0.198 10 false IG1 5.708,2.094 6.167,2.292 0.458,0.198 10 false G87 5.74,1.885 6.052,2.083 0.313,0.198 10 false 18 6.115,2.073 6.573,2.271 0.458,0.198 10 false IG2 0.198,2.208 0.354,2.406 0.156,0.198 10 false B 1.396,3.531 1.854,3.729 0.458,0.198 10 false IG2 0.677,3.135 0.875,3.344 0.198,0.208 10 false 5 1.24,3.135 1.396,3.333 0.156,0.198 10 false 2 0.667,3.917 0.823,4.115 0.156,0.198 10 false 3 1.219,3.917 1.375,4.115 0.156,0.198 10 false 1 3.396,4.094 4.542,4.313 1.146,0.219 10 false EFI-MAIN NO. 1 2.146,4.344 3.292,4.563 1.146,0.219 10 false EFI-MAIN NO. 1 2.76,6.74 2.917,6.938 0.156,0.198 10 false 5 4.229,3.188 4.385,3.385 0.156,0.198 10 false 3 3.406,3.615 3.563,3.813 0.156,0.198 10 false 2 4.219,3.625 4.375,3.823 0.156,0.198 10 false 1 4.563,3.469 5.938,3.667 1.375,0.198 10 false EFI NO. 2 5.708,3.323 6.167,3.521 0.458,0.198 10 false A66 5.76,3.125 5.917,3.323 0.156,0.198 10 false 1 6.125,3.292 6.438,3.49 0.313,0.198 10 false +B 2.677,5.333 3.135,5.531 0.458,0.198 10 false G84 2.76,5.104 2.917,5.302 0.156,0.198 10 false 6 2.229,5.333 2.844,5.531 0.615,0.198 10 false IG1D 1.813,6.333 2.427,6.531 0.615,0.198 10 false IG2D 1.438,6.354 1.896,6.552 0.458,0.198 10 false G82 1.521,6.135 1.677,6.333 0.156,0.198 10 false 9 1.427,7.542 1.885,7.74 0.458,0.198 10 false G82 1.51,7.323 1.667,7.521 0.156,0.198 10 false 2 1.823,7.531 2.135,7.729 0.313,0.198 10 false +B 2.167,6.958 2.625,7.156 0.458,0.198 10 false STAR 2.677,7.469 3.135,7.667 0.458,0.198 10 false G82 2.76,7.281 2.917,7.479 0.156,0.198 10 false 7 2.677,6.969 3.135,7.167 0.458,0.198 10 false G82 2.26,7.469 2.719,7.667 0.458,0.198 10 false STA 3.729,6.969 3.885,7.167 0.156,0.198 10 false B 3.729,6.698 3.885,6.896 0.156,0.198 10 false L 3.469,6.844 3.625,7.042 0.156,0.198 10 false 4 4.469,6.573 4.625,6.771 0.156,0.198 10 false 9 0.5,6.521 0.958,6.719 0.458,0.198 10 false IG2 0.656,7.698 1.115,7.896 0.458,0.198 10 false AM2 0.208,8.063 0.365,8.26 0.156,0.198 10 false A 1.26,7.938 3.063,8.406 1.802,0.469 10 false Certification ECU (Smart Key ECU Assembly) 3.583,7.51 4.042,7.708 0.458,0.198 10 false B36 3.594,7.719 4.927,8.167 1.333,0.448 10 false Park/Neutral Position Switch Assembly 4.948,7.292 5.104,7.49 0.156,0.198 10 false C 5.344,6.271 5.5,6.469 0.156,0.198 10 false D 5.719,5.677 6.177,5.875 0.458,0.198 10 false A66 5.75,5.479 6.063,5.677 0.313,0.198 10 false 17 5.75,6.5 6.063,6.698 0.313,0.198 10 false 21 5.719,6.698 6.177,6.896 0.458,0.198 10 false A66 6.104,5.667 6.563,5.865 0.458,0.198 10 false CLL 6.104,6.708 6.563,6.906 0.458,0.198 10 false STA 5.385,7.375 7.104,7.646 1.719,0.271 10 false Engine Stop and Start ECU 0.083,0.063 2.031,0.313 1.948,0.25 12 false w/ Entry and Start System: 4.635,4.646 4.792,4.844 0.156,0.198 10 false E 3.406,3.177 3.604,3.385 0.198,0.208 10 false 5

A350620E02
1.875,2.833 4.646,3.021 2.771,0.188 10 false Instrument Panel Junction Block Assembly 1.771,0.99 2.083,1.188 0.313,0.198 10 false 3A 1.813,0.813 1.969,1.01 0.156,0.198 10 false 1 1.771,1.427 2.083,1.625 0.313,0.198 10 false 3D 1.813,1.229 1.969,1.427 0.156,0.198 10 false 9 2.667,1.667 4.042,1.865 1.375,0.198 10 false IG1 NO. 1 3.656,1.146 4.573,1.344 0.917,0.198 10 false EPS-IG 4.615,1 4.927,1.198 0.313,0.198 10 false 3D 4.615,0.802 4.927,1 0.313,0.198 10 false 43 4.594,1.948 4.906,2.146 0.313,0.198 10 false 3C 4.604,1.75 4.917,1.948 0.313,0.198 10 false 48 2.969,2.104 3.427,2.302 0.458,0.198 10 false AM1 0.208,2.271 0.365,2.469 0.156,0.198 10 false B 1.781,2.417 2.094,2.615 0.313,0.198 10 false 3B 1.781,2.229 2.094,2.427 0.313,0.198 10 false 14 3.208,2.563 3.667,2.76 0.458,0.198 10 false IGN 4.615,1.229 4.927,1.427 0.313,0.198 10 false 43 4.615,1.406 4.927,1.604 0.313,0.198 10 false 3C 4.604,2.427 4.917,2.625 0.313,0.198 10 false 3C 4.604,2.208 4.917,2.406 0.313,0.198 10 false 37 5.708,1 6.167,1.198 0.458,0.198 10 false G87 5.75,0.802 6.063,1 0.313,0.198 10 false 21 6.104,0.969 6.563,1.167 0.458,0.198 10 false IG1 6.115,2.396 6.573,2.594 0.458,0.198 10 false IG2 5.708,2.406 6.167,2.604 0.458,0.198 10 false G87 5.75,2.208 6.063,2.406 0.313,0.198 10 false 18 1.25,3.146 1.406,3.344 0.156,0.198 10 false 2 1.24,3.927 1.396,4.125 0.156,0.198 10 false 1 0.656,3.938 0.813,4.135 0.156,0.198 10 false 3 0.656,3.135 0.813,3.333 0.156,0.198 10 false 5 1.406,3.521 1.865,3.719 0.458,0.198 10 false IG2 5.708,3.427 6.167,3.625 0.458,0.198 10 false A66 5.781,3.219 5.938,3.417 0.156,0.198 10 false 1 6.104,3.396 6.417,3.594 0.313,0.198 10 false +B 4.552,3.563 5.927,3.76 1.375,0.198 10 false EFI NO. 2 4.302,3.313 4.458,3.51 0.156,0.198 10 false 3 3.5,3.302 3.656,3.5 0.156,0.198 10 false 5 4.292,3.625 4.448,3.823 0.156,0.198 10 false 1 3.49,3.615 3.646,3.813 0.156,0.198 10 false 2 3.479,4.094 4.573,4.323 1.094,0.229 10 false EFI-MAIN NO. 1 2.125,3.938 3.219,4.167 1.094,0.229 10 false EFI-MAIN NO. 1 4.635,4.469 4.792,4.667 0.156,0.198 10 false E 1.635,6.771 2.75,7.302 1.115,0.531 10 false Ignition or Starter Switch Assembly 1.625,6.563 1.938,6.76 0.313,0.198 10 false G4 2.469,5.823 2.927,6.021 0.458,0.198 10 false IG2 0.583,7.635 1.042,7.833 0.458,0.198 10 false AM2 1.677,5.792 2.135,5.99 0.458,0.198 10 false AM2 1.448,5.771 1.604,5.969 0.156,0.198 10 false 4 1.438,5.25 1.594,5.448 0.156,0.198 10 false 5 1.677,5.25 2.135,5.448 0.458,0.198 10 false AM1 2.469,5.219 2.927,5.417 0.458,0.198 10 false IG1 2.438,5.552 2.896,5.75 0.458,0.198 10 false ST2 2.823,5.552 2.979,5.75 0.156,0.198 10 false 2 2.813,5.219 2.969,5.417 0.156,0.198 10 false 8 2.823,5.813 2.979,6.01 0.156,0.198 10 false 3 0.51,6.531 0.969,6.729 0.458,0.198 10 false IG2 0.198,8.073 0.354,8.271 0.156,0.198 10 false A 3.375,7.656 4.708,8.094 1.333,0.438 10 false Park/Neutral Position Switch Assembly 3.375,7.438 3.833,7.635 0.458,0.198 10 false B36 3.719,6.969 3.875,7.167 0.156,0.198 10 false B 3.729,6.708 3.885,6.906 0.156,0.198 10 false L 3.49,6.865 3.646,7.063 0.156,0.198 10 false 4 4.479,6.563 4.635,6.76 0.156,0.198 10 false 9 4.948,7.292 5.104,7.49 0.156,0.198 10 false C 4.927,6.281 5.083,6.479 0.156,0.198 10 false D 5.719,5.677 6.177,5.875 0.458,0.198 10 false A66 5.719,6.698 6.177,6.896 0.458,0.198 10 false A66 5.76,5.469 6.073,5.667 0.313,0.198 10 false 17 5.75,6.49 6.063,6.688 0.313,0.198 10 false 21 6.125,6.698 6.583,6.896 0.458,0.198 10 false STA 6.115,5.677 6.573,5.875 0.458,0.198 10 false CLL 5.385,7.417 7.115,7.677 1.729,0.26 10 false Engine Stop and Start ECU 0.083,0.052 2.667,0.302 2.583,0.25 12 false w/o Entry and Start System:

A375402E01
0.292,0.104 0.448,0.302 0.156,0.198 10 false A 0.844,0.094 1,0.292 0.156,0.198 10 false B 0.99,0.563 1.448,0.76 0.458,0.198 10 false ALT 1.375,2.458 1.833,2.656 0.458,0.198 10 false B96 1.448,2.26 1.604,2.458 0.156,0.198 10 false 1 1.729,2.458 1.885,2.656 0.156,0.198 10 false B 2.406,1.885 2.865,2.083 0.458,0.198 10 false SL2 2.781,1.885 3.24,2.083 0.458,0.198 10 false B87 2.875,1.688 3.031,1.885 0.156,0.198 10 false 1 2.406,2.344 2.865,2.542 0.458,0.198 10 false SL1 2.781,2.333 3.24,2.531 0.458,0.198 10 false B87 2.865,2.146 3.021,2.344 0.156,0.198 10 false 2 1.677,2.802 2.906,3 1.229,0.198 10 false Starter Assembly 4.104,2.552 5.333,2.75 1.229,0.198 10 false ST NO. 2 3.906,2.094 4.063,2.292 0.156,0.198 10 false 1 4.719,2.094 4.875,2.292 0.156,0.198 10 false 2 4.719,1.76 4.875,1.958 0.156,0.198 10 false 5 3.917,1.76 4.073,1.958 0.156,0.198 10 false 3 5.604,2.219 6.063,2.417 0.458,0.198 10 false A66 5.656,2.031 5.969,2.229 0.313,0.198 10 false 23 6,2.229 6.615,2.427 0.615,0.198 10 false STA2 3.781,0.583 5.01,0.781 1.229,0.198 10 false ST NO. 2 2.333,4.083 3.563,4.281 1.229,0.198 10 false ST NO. 1 1.521,3.604 1.823,3.802 0.302,0.198 10 false ST 2.135,3.625 2.292,3.823 0.156,0.198 10 false 1 2.969,3.635 3.125,3.833 0.156,0.198 10 false 2 2.99,3.302 3.146,3.5 0.156,0.198 10 false 5 2.135,3.292 2.292,3.49 0.156,0.198 10 false 3 3.813,3.729 3.969,3.927 0.156,0.198 10 false C 6.031,4.594 6.646,4.792 0.615,0.198 10 false BIN1 5.625,4.594 6.083,4.792 0.458,0.198 10 false A86 5.688,4.406 5.844,4.604 0.156,0.198 10 false 3 3.354,4.76 3.813,4.958 0.458,0.198 10 false BBC 3.135,5.333 4.313,5.531 1.177,0.198 10 false BBC NO. 2 6.042,5.146 6.656,5.344 0.615,0.198 10 false BIN2 5.604,5.156 6.063,5.354 0.458,0.198 10 false A86 5.677,4.906 5.833,5.104 0.156,0.198 10 false 1 6,3.031 6.615,3.229 0.615,0.198 10 false DGND 5.604,3.042 6.063,3.24 0.458,0.198 10 false A66 5.688,2.844 5.844,3.042 0.156,0.198 10 false 6 0.448,5.844 1.521,6.042 1.073,0.198 10 false FL MAIN 0.604,7.323 1.677,7.521 1.073,0.198 10 false Battery 2.323,5.729 2.781,5.927 0.458,0.198 10 false STA 2.792,5.615 3.104,5.813 0.313,0.198 10 false 29 2.281,6.063 2.74,6.26 0.458,0.198 10 false NSW 2.781,5.979 3.094,6.177 0.313,0.198 10 false 23 2.229,6.49 2.844,6.688 0.615,0.198 10 false CANH 2.771,6.323 3.083,6.521 0.313,0.198 10 false 13 2.25,6.99 2.865,7.188 0.615,0.198 10 false CANL 2.771,6.813 3.083,7.01 0.313,0.198 10 false 26 3.875,6.052 4.031,6.25 0.156,0.198 10 false D 2.24,7.333 2.854,7.531 0.615,0.198 10 false MREL 2.771,7.208 3.083,7.406 0.313,0.198 10 false 46 3.365,7.323 3.521,7.521 0.156,0.198 10 false E 1.854,7.76 2.313,7.958 0.458,0.198 10 false A62 1.844,7.938 2.302,8.135 0.458,0.198 10 false ECM 5.604,6.5 6.063,6.698 0.458,0.198 10 false G87 5.594,7.01 6.052,7.208 0.458,0.198 10 false G87 5.646,6.292 5.958,6.49 0.313,0.198 10 false 13 5.646,6.802 5.958,7 0.313,0.198 10 false 14 5.99,6.49 6.604,6.688 0.615,0.198 10 false CANH 5.99,7.01 6.604,7.208 0.615,0.198 10 false CANL 5.417,7.531 7.135,7.75 1.719,0.219 10 false Engine Stop and Start ECU 0.292,8.49 3.958,8.688 3.667,0.198 10 false : CAN Communication Line 5.99,0.552 6.604,0.75 0.615,0.198 10 false GND1 5.625,0.573 6.083,0.771 0.458,0.198 10 false A86 5.677,0.385 5.833,0.583 0.156,0.198 10 false 8 5.99,1.427 6.604,1.625 0.615,0.198 10 false GND2 5.615,1.438 6.073,1.635 0.458,0.198 10 false A86 5.688,1.25 5.844,1.448 0.156,0.198 10 false 2


for Manual Transaxle:


A375403E01
5.719,1.01 6.177,1.208 0.458,0.198 10 false G87 5.75,0.813 6.063,1.01 0.313,0.198 10 false 21 6.094,1.01 6.552,1.208 0.458,0.198 10 false IG1 5.75,1.896 6.063,2.094 0.313,0.198 10 false 18 5.698,2.094 6.156,2.292 0.458,0.198 10 false G87 6.094,2.094 6.552,2.292 0.458,0.198 10 false IG2 4.615,0.99 4.927,1.188 0.313,0.198 10 false 3D 4.625,0.802 4.938,1 0.313,0.198 10 false 43 3.625,1.146 4.542,1.344 0.917,0.198 10 false EPS-IG 2.656,1.698 3.375,1.906 0.719,0.208 10 false IG1 NO. 1 1.781,0.99 2.094,1.188 0.313,0.198 10 false 3A 1.813,0.792 1.969,0.99 0.156,0.198 10 false 1 1.792,1.417 2.104,1.615 0.313,0.198 10 false 3D 1.823,1.229 1.979,1.427 0.156,0.198 10 false 9 1.771,2.094 2.083,2.292 0.313,0.198 10 false 3B 1.792,1.875 2.104,2.073 0.313,0.198 10 false 14 3.198,2.24 3.656,2.438 0.458,0.198 10 false IGN 4.604,2.083 4.917,2.281 0.313,0.198 10 false 3C 4.615,1.875 4.927,2.073 0.313,0.198 10 false 37 4.615,1.417 4.927,1.615 0.313,0.198 10 false 3C 4.615,1.219 4.927,1.417 0.313,0.198 10 false 43 0.208,2.208 0.365,2.406 0.156,0.198 10 false B 1.417,3.521 1.875,3.719 0.458,0.198 10 false IG2 0.688,3.125 0.844,3.323 0.156,0.198 10 false 5 1.26,3.135 1.417,3.333 0.156,0.198 10 false 2 0.688,3.948 0.844,4.146 0.156,0.198 10 false 3 1.26,3.938 1.417,4.135 0.156,0.198 10 false 1 4.583,3.469 5.375,3.667 0.792,0.198 10 false EFI NO. 2 1.833,2.688 4.552,2.906 2.719,0.219 10 false Instrument Panel Junction Block Assembly 3.385,4.115 4.469,4.344 1.083,0.229 10 false EFI-MAIN NO. 1 4.229,3.177 4.385,3.375 0.156,0.198 10 false 3 3.417,3.188 3.573,3.385 0.156,0.198 10 false 5 3.417,3.594 3.573,3.792 0.156,0.198 10 false 2 4.229,3.604 4.385,3.802 0.156,0.198 10 false 1 4.646,4.625 4.802,4.823 0.156,0.198 10 false E 2.135,4.354 3.219,4.583 1.083,0.229 10 false EFI-MAIN NO. 1 5.708,3.323 6.167,3.521 0.458,0.198 10 false A66 5.771,3.115 5.927,3.313 0.156,0.198 10 false 1 6.115,3.313 6.427,3.51 0.313,0.198 10 false +B 6.115,5.688 6.573,5.885 0.458,0.198 10 false CLL 5.719,5.698 6.177,5.896 0.458,0.198 10 false A66 5.75,5.479 6.063,5.677 0.313,0.198 10 false 17 2.229,5.333 2.604,5.531 0.375,0.198 10 false IG1D 2.688,5.344 3.146,5.542 0.458,0.198 10 false G84 2.76,5.125 2.917,5.323 0.156,0.198 10 false 6 2.688,6.729 3.146,6.927 0.458,0.198 10 false G82 2.667,7.49 3.125,7.688 0.458,0.198 10 false G82 2.177,6.719 2.792,6.917 0.615,0.198 10 false STAR 2.771,6.51 2.927,6.708 0.156,0.198 10 false 5 2.271,7.469 2.729,7.667 0.458,0.198 10 false STA 2.75,7.281 2.906,7.479 0.156,0.198 10 false 7 1.833,7.552 2.146,7.75 0.313,0.198 10 false +B 1.417,7.542 1.875,7.74 0.458,0.198 10 false G82 1.427,6.354 1.885,6.552 0.458,0.198 10 false G82 1.823,6.344 2.438,6.542 0.615,0.198 10 false IG2D 0.5,6.51 0.958,6.708 0.458,0.198 10 false IG2 0.646,7.719 1.104,7.917 0.458,0.198 10 false AM2 0.198,8.063 0.354,8.26 0.156,0.198 10 false A 1.375,7.917 2.906,8.406 1.531,0.49 10 false Certification ECU (Smart Key ECU Assembly) 5.438,7.354 7.156,7.771 1.719,0.417 10 false Engine Stop and Start ECU 5.719,6.708 6.177,6.906 0.458,0.198 10 false A66 6.104,6.708 6.563,6.906 0.458,0.198 10 false STA 5.771,6.51 6.083,6.708 0.313,0.198 10 false 21 5.344,6.281 5.5,6.479 0.156,0.198 10 false D 4.948,7.292 5.104,7.49 0.156,0.198 10 false C 3.521,7 3.979,7.198 0.458,0.198 10 false A4 3.51,7.198 4.844,7.615 1.333,0.417 10 false Clutch Start Switch Assembly (for Lower) 3.49,6.583 3.646,6.781 0.156,0.198 10 false 2 4.469,6.594 4.625,6.792 0.156,0.198 10 false 1 0.094,0.094 4.865,0.333 4.771,0.24 12 false w/ Entry and Start System: 1.531,6.146 1.688,6.344 0.156,0.198 10 false 9 1.521,7.354 1.677,7.552 0.156,0.198 10 false 2

A375404E01
0.083,0.073 5.042,0.313 4.958,0.24 12 false w/o Entry and Start System: 1.896,2.854 4.594,3.083 2.698,0.229 10 false Instrument Panel Junction Block Assembly 1.76,0.99 2.073,1.188 0.313,0.198 10 false 3A 1.802,0.802 1.958,1 0.156,0.198 10 false 1 0.198,2.271 0.354,2.469 0.156,0.198 10 false B 1.781,1.417 2.094,1.615 0.313,0.198 10 false 3D 1.802,1.229 1.958,1.427 0.156,0.198 10 false 9 2.635,1.677 3.344,1.885 0.708,0.208 10 false IG1 NO. 1 3.656,1.167 4.229,1.375 0.573,0.208 10 false EPS-IG 4.615,0.99 4.927,1.188 0.313,0.198 10 false 3D 4.615,0.813 4.927,1.01 0.313,0.198 10 false 43 5.719,1 6.177,1.198 0.458,0.198 10 false G87 5.76,0.792 6.073,0.99 0.313,0.198 10 false 21 6.104,0.99 6.563,1.188 0.458,0.198 10 false IG1 4.594,1.427 4.906,1.625 0.313,0.198 10 false 3C 4.604,1.229 4.917,1.427 0.313,0.198 10 false 43 2.958,2.115 3.417,2.313 0.458,0.198 10 false AM1 4.583,1.958 4.896,2.156 0.313,0.198 10 false 3C 4.594,1.76 4.906,1.958 0.313,0.198 10 false 48 1.76,2.427 2.073,2.625 0.313,0.198 10 false 3B 3.177,2.573 3.635,2.771 0.458,0.198 10 false IGN 4.604,2.417 4.917,2.615 0.313,0.198 10 false 3C 4.615,2.229 4.927,2.427 0.313,0.198 10 false 37 1.792,2.219 2.104,2.417 0.313,0.198 10 false 14 1.385,3.521 1.844,3.719 0.458,0.198 10 false IG2 1.281,3.146 1.438,3.344 0.156,0.198 10 false 2 1.271,3.938 1.427,4.135 0.156,0.198 10 false 1 0.688,3.146 0.844,3.344 0.156,0.198 10 false 5 0.708,3.927 0.938,4.094 0.229,0.167 10 false 3 4.552,3.563 5.25,3.781 0.698,0.219 10 false EFI NO. 2 4.313,3.302 4.542,3.469 0.229,0.167 10 false 3 3.5,3.281 3.656,3.479 0.156,0.198 10 false 5 3.49,3.604 3.646,3.802 0.156,0.198 10 false 2 4.313,3.583 4.469,3.781 0.156,0.198 10 false 1 6.115,2.417 6.573,2.615 0.458,0.198 10 false IG2 5.698,2.417 6.156,2.615 0.458,0.198 10 false G87 5.74,2.219 6.052,2.417 0.313,0.198 10 false 18 6.135,3.417 6.448,3.615 0.313,0.198 10 false +B 5.708,3.427 6.167,3.625 0.458,0.198 10 false A66 5.781,3.219 5.938,3.417 0.156,0.198 10 false 1 4.635,4.458 4.792,4.656 0.156,0.198 10 false E 3.458,4.115 4.521,4.313 1.063,0.198 10 false EFI-MAIN NO. 1 2.135,3.938 3.198,4.135 1.063,0.198 10 false EFI-MAIN NO. 1 0.49,6.521 0.948,6.719 0.458,0.198 10 false IG2 2.469,5.229 2.927,5.427 0.458,0.198 10 false IG1 2.448,5.573 2.906,5.771 0.458,0.198 10 false ST2 2.469,5.833 2.927,6.031 0.458,0.198 10 false IG2 1.667,5.792 2.125,5.99 0.458,0.198 10 false AM2 0.573,7.646 1.031,7.844 0.458,0.198 10 false AM2 1.667,5.281 2.125,5.479 0.458,0.198 10 false AM1 1.458,5.24 1.615,5.438 0.156,0.198 10 false 5 1.458,5.781 1.615,5.979 0.156,0.198 10 false 4 2.823,5.229 2.979,5.427 0.156,0.198 10 false 8 2.823,5.563 2.979,5.76 0.156,0.198 10 false 2 2.823,5.802 3.052,5.969 0.229,0.167 10 false 3 1.552,6.479 1.865,6.677 0.313,0.198 10 false G4 1.573,6.677 2.698,7.104 1.125,0.427 10 false Ignition or Starter Switch Assembly 5.719,5.677 6.177,5.875 0.458,0.198 10 false A66 5.76,5.479 6.073,5.677 0.313,0.198 10 false 17 6.115,5.677 6.573,5.875 0.458,0.198 10 false CLL 4.938,6.281 5.094,6.479 0.156,0.198 10 false D 5.719,6.708 6.177,6.906 0.458,0.198 10 false A66 5.75,6.5 6.063,6.698 0.313,0.198 10 false 21 6.104,6.708 6.563,6.906 0.458,0.198 10 false STA 4.948,7.292 5.104,7.49 0.156,0.198 10 false C 5.427,7.396 7.156,7.688 1.729,0.292 10 false Engine Stop and Start ECU 0.208,8.063 0.365,8.26 0.156,0.198 10 false A 3.333,7.125 4.667,7.76 1.333,0.635 10 false Clutch Start Switch Assembly (for Lower) 3.344,6.927 3.656,7.125 0.313,0.198 10 false A4 3.469,6.563 3.625,6.76 0.156,0.198 10 false 2 4.469,6.563 4.625,6.76 0.156,0.198 10 false 1


A375405E01
0.292,0.104 0.448,0.302 0.156,0.198 10 false A 0.844,0.104 1,0.302 0.156,0.198 10 false B 0.979,0.521 1.438,0.719 0.458,0.198 10 false ALT 3.448,1.688 3.76,1.885 0.313,0.198 10 false B6 3.5,1.5 3.656,1.698 0.156,0.198 10 false 1 2.021,1.771 2.333,1.969 0.313,0.198 10 false C6 2.073,1.563 2.229,1.76 0.156,0.198 10 false 1 2.24,2.313 3.427,2.531 1.188,0.219 10 false Starter Assembly 0.448,5.844 1.521,6.042 1.073,0.198 10 false FL MAIN 0.604,7.313 1.677,7.51 1.073,0.198 10 false Battery 2.333,4.104 3.563,4.302 1.229,0.198 10 false ST NO. 1 1.542,3.594 2.771,3.792 1.229,0.198 10 false ST 2.135,3.302 2.292,3.5 0.156,0.198 10 false 5 2.958,3.302 3.115,3.5 0.156,0.198 10 false 3 2.125,3.625 2.281,3.823 0.156,0.198 10 false 1 2.948,3.635 3.104,3.833 0.156,0.198 10 false 2 3.813,3.729 3.969,3.927 0.156,0.198 10 false C 2.344,5.708 2.802,5.906 0.458,0.198 10 false STA 2.76,5.594 3.073,5.792 0.313,0.198 10 false 29 2.292,6.063 2.75,6.26 0.458,0.198 10 false NSW 2.771,5.927 3.083,6.125 0.313,0.198 10 false 23 3.344,6.052 3.5,6.25 0.156,0.198 10 false D 2.25,6.49 2.865,6.688 0.615,0.198 10 false CANH 2.771,6.323 3.083,6.521 0.313,0.198 10 false 13 2.281,7 2.896,7.198 0.615,0.198 10 false CANL 2.771,6.813 3.083,7.01 0.313,0.198 10 false 26 2.25,7.333 2.865,7.531 0.615,0.198 10 false MREL 2.76,7.24 3.073,7.438 0.313,0.198 10 false 46 3.365,7.313 3.521,7.51 0.156,0.198 10 false E 5.427,7.51 7.146,7.771 1.719,0.26 10 false Engine Stop and Start ECU 5.604,6.5 6.063,6.698 0.458,0.198 10 false G87 5.635,6.292 5.948,6.49 0.313,0.198 10 false 13 5.99,6.5 6.604,6.698 0.615,0.198 10 false CANH 6.01,7.01 6.625,7.208 0.615,0.198 10 false CANL 5.604,7 6.063,7.198 0.458,0.198 10 false G87 5.635,6.813 5.948,7.01 0.313,0.198 10 false 14 1.823,7.74 2.281,7.938 0.458,0.198 10 false A62 1.813,7.969 2.271,8.167 0.458,0.198 10 false ECM 0.281,8.5 3.948,8.698 3.667,0.198 10 false : CAN Communication Line 6.021,4.646 6.635,4.844 0.615,0.198 10 false BIN1 6.01,5.271 6.625,5.469 0.615,0.198 10 false BIN2 4.479,4.792 4.938,4.99 0.458,0.198 10 false BBC 5.615,4.646 6.073,4.844 0.458,0.198 10 false A86 5.708,4.448 5.865,4.646 0.156,0.198 10 false 3 5.615,5.26 6.073,5.458 0.458,0.198 10 false A86 5.698,5.031 5.854,5.229 0.156,0.198 10 false 1 4.229,5.438 5.354,5.646 1.125,0.208 10 false BBC NO. 2 5.615,3.271 6.073,3.469 0.458,0.198 10 false A66 5.698,3.063 5.854,3.26 0.156,0.198 10 false 6 6.01,3.281 6.625,3.479 0.615,0.198 10 false DGND 5.615,1.115 6.073,1.313 0.458,0.198 10 false A86 5.698,0.906 5.854,1.104 0.156,0.198 10 false 8 6.01,1.115 6.625,1.313 0.615,0.198 10 false GND1 6.021,2.271 6.635,2.469 0.615,0.198 10 false GND2 5.604,2.281 6.063,2.479 0.458,0.198 10 false A86 5.688,2.073 5.844,2.271 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

for CVT:

When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

for Manual Transaxle:

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

for CVT:

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.

·

for Manual Transaxle:

When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CRANKING
a.

Turn the ignition switch to START and check that the engine cranks.


Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

2.PERFORM ACTIVE TEST USING GTS (STARTER)

B

5.PERFORM ACTIVE TEST USING GTS (STARTER)
2.PERFORM ACTIVE TEST USING GTS (STARTER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter.

Powertrain > Stop and Start > Active Test
Tester Display
Starter
50004 227 7

e.

Check whether the engine cranks while the Active Test "Starter" is being performed.

NOTICE:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Proceed to
OK
NG



OK

GO TO DTC P1603 (CONFIRM CAUSE OF ENGINE STALL)

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)
A348463C17
0.958,0.5 1.302,0.76 0.344,0.26 3.396,0.5 3.74,0.76 0.344,0.26 5.813,0.51 6.26,0.813 0.448,0.302 0.365,2.073 0.719,1.563 true 0.906,2.052 0.74,1.75 true 2.438,2.094 2.604,1.708 true 5.542,2.063 5.771,1.771 true 6.354,2.052 6.198,1.771 true 0.323,0.115 0.635,0.313 0.313,0.198 10 false *a 1.01,0.552 1.323,0.75 0.313,0.198 10 false A86 3.448,0.563 3.76,0.76 0.313,0.198 10 false A66 5.906,0.583 6.438,0.781 0.531,0.198 10 false G87 0.844,2.104 1.156,2.302 0.313,0.198 10 false BIN1 0.229,2.104 0.542,2.302 0.313,0.198 10 false BIN2 2.323,2.115 2.635,2.313 0.313,0.198 10 false +B 6.292,2.083 6.604,2.281 0.313,0.198 10 false IG1 5.427,2.094 5.74,2.292 0.313,0.198 10 false IG2
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -


a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-1 (BIN2) - Body ground Always 9.5 to 14 V
A86-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
G87-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V
G87-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the A86 and A66 engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-2 (GND2) - Body ground Always Below 1 Ω
A86-8 (GND1) - Body ground Always Below 1 Ω
A66-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING GTS (STARTER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter.

Powertrain > Stop and Start > Active Test
Tester Display
Starter
50004 227 7

e.

Check whether the engine cranks while the Active Test "Starter" is being performed.

NOTICE:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Result Proceed to
Engine cranks (for CVT) A
Engine does not crank (for CVT) B
Engine cranks (for Manual Transaxle) C
Engine does not crank (for Manual Transaxle) D



A

6.READ VALUE USING GTS (NEUTRAL SWITCH)

B

15.CHECK ENGINE STOP AND START ECU (STA, STA2 SIGNAL)

C

30.READ VALUE USING GTS (CLUTCH LOWER SW)

D

39.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
6.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 227 9
OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in P or N ON
Shift lever not in P or N OFF



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)

B

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

C

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A66 engine stop and start ECU connector.


c.

Disconnect the B36 park/neutral position switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - A66-17 (CLL) Always Below 1 Ω
G82-5 (STAR) - Body ground Always 10 kΩ or higher
A66-17 (CLL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)
a.
A342958C23
0.083,0.75 0.438,1.052 0.354,0.302 1.021,1.99 1.281,1.781 true 0.24,0.146 0.552,0.344 0.313,0.198 10 false *a 0.135,0.813 0.594,1.01 0.458,0.198 10 false A66 0.771,1.979 1.229,2.177 0.458,0.198 10 false CLL
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-17 (CLL) - Body ground Engine started using push start switch assembly (ignition switch turned START) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>3ZR-FAE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)
a.
A285192C09
1.5,0.625 1.865,0.875 0.365,0.25 2.729,2.021 2.208,2.031 true 0.302,0.281 0.615,0.479 0.313,0.198 10 false *a 1.583,0.688 2.042,0.885 0.458,0.198 10 false G4 2.823,1.927 3.281,2.125 0.458,0.198 10 false AM2
*a Front view of wire harness connector:
(to Ignition or Starter Switch Assembly)


Disconnect the ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G4-4 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G4 ignition or starter switch assembly connector.


b.

Disconnect the B36 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - B36-4 (B) Always Below 1 Ω
G4-2 (ST2) - Body ground Always 10 kΩ or higher
B36-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

B

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)

C

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - ST NO. 1 relay terminal 2 Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the G4 ignition or starter switch assembly connector.


b.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - ST NO. 1 relay terminal 2 Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK ENGINE STOP AND START ECU (STA, STA2 SIGNAL)
A346331C71
3.188,0.615 3.708,0.844 0.521,0.229 3.427,1.344 3.469,2.198 true 3.271,1.333 2.708,2.188 true 3.74,1.229 4.563,2.281 true 3.313,0.646 3.771,0.844 0.458,0.198 10 false A66 3.354,2.25 3.719,2.458 0.365,0.208 10 false STA 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 2.542,2.24 3.156,2.438 0.615,0.198 10 false STA2 4.427,2.313 5.042,2.51 0.615,0.198 10 false DGND
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Connect an oscilloscope to the A66-21 (STA), A66-23 (STA2) and A66-6 (DGND) terminals of the engine stop and start ECU connector.


b.
A285702E16
0.042,0.677 0.5,0.875 0.458,0.198 10 false STA 0.042,1.281 0.5,1.479 0.458,0.198 10 false STA2 1.198,1.771 2.958,1.958 1.76,0.188 10 false 0.016 seconds or more 0.031,0.875 1.865,1.073 1.833,0.198 10 false (ST NO. 1 Relay) 0.031,1.458 1.865,1.656 1.833,0.198 10 false (ST NO. 2 Relay)

Check the waveform immediately after turning the ignition switch START.

Item Condition
Tester Connection A66-21 (STA) - A66-6 (DGND)
A66-23 (STA2) - A66-6 (DGND)
Condition Engine started by ignition or starter switch assembly*1 or push start switch assembly*2 operation

*1: w/o Entry and Start System

*2: w/ Entry and Start System


Result:
Result Proceed to
Delay between ST NO. 1 relay turning on and ST NO. 2 relay turning on: between 0.03 and 0.06 seconds A
Delay between ST NO. 1 relay turning on and ST NO. 2 relay turning on: not between 0.03 and 0.06 seconds B
ST NO. 1 relay turns on and ST NO. 2 relay does not turn on C
ST NO. 1 relay and ST NO. 2 relay do not turn on D


NOTICE:

After replacing the engine stop and start ECU, make sure that the drive plate and ring gear sub-assembly and starter pinion gear are not excessively worn. A malfunction in the delay circuit may cause the drive plate and ring gear sub-assembly or starter pinion gear to be worn or damaged.




A

16.INSPECT RELAY (ST NO. 1, ST NO. 2 RELAY)

B

C

28.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)

D

19.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
16.INSPECT RELAY (ST NO. 1, ST NO. 2 RELAY)


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - BATTERY)

NG

REPLACE RELAY (ST NO. 1, ST NO. 2 RELAY)

17.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - BATTERY)
A350457C01
0.146,0.125 0.458,0.323 0.313,0.198 10 false *1 0.365,1.698 0.677,1.896 0.313,0.198 10 false *a 2.417,0.104 2.729,0.302 0.313,0.198 10 false *b
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*a ST NO. 1 Relay Terminal
*b ST NO. 2 Relay Terminal


a.

Remove the ST NO. 1 and ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 5 - Body ground Always 9.5 to 14 V
ST NO. 2 relay terminal 5 - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (ST NO. 1, ST NO. 2 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 and ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the B87 starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 3 - B87-2 (SL1) Always Below 1 Ω
ST NO. 2 relay terminal 3 - B87-1 (SL2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BODY GROUND)
a.

Remove the ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 2 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


c.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the B36 park/neutral position switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
A66-21 (STA) - Body ground Always 10 kΩ or higher
ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 2 RELAY)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Remove the ST NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


c.

Disconnect the A62 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-23 (STA2) - ST NO. 2 relay terminal 2 Always Below 1 Ω
A66-23 (STA2) - Body ground Always 10 kΩ or higher
ST NO. 2 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.CHECK STARTER SIGNAL (OUTPUT WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK STARTER SIGNAL (OUTPUT WAVEFORM)
a.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter Motor Drive Magnet Switch.


b.

Connect the positive (+) lead of an oscilloscope to the positive (+) battery terminal and the negative (-) lead to the negative (-) battery terminal.


c.

While performing the Active Test "Starter Motor Drive Magnet Switch" to forcibly operate the starter motor, count the number of times the waveform drops.

NOTICE:
·

The Active Test "Starter Motor Drive Magnet Switch" is stopped automatically after the starter motor operates for 3 seconds.

·

Do not forcibly operate the starter pinion.



A285237E02
3.438,0.781 3.583,0.417 3.583,0.417 3.833,0.417 false 0.104,0.729 0.719,0.927 0.615,0.198 10 false Normal: 0.156,2.156 0.771,2.354 0.615,0.198 10 false Abnormal: 0.719,0.917 2.042,1.135 1.323,0.219 10 false Approximately 12 V 1.938,1.24 3.927,1.438 1.99,0.198 10 false 7.6 to 9.3 V* 3.906,0.323 5.667,0.542 1.76,0.219 10 false Approximately 0.1 seconds 3.396,1.698 5.073,1.896 1.677,0.198 10 false Less than 3 seconds 5.167,3.177 7.083,3.5 1.917,0.323 10 false *: Varies with battery condition 2.396,2.49 5.031,3.042 2.635,0.552 10 false If the waveform does not change either the starter inrush current reduction relay or starter assembly is not operating. 0.729,2.302 2.052,2.521 1.323,0.219 10 false Approximately 12 V

Standard:

Waveform drops 2 times


Result:
Number of Times Waveform Dropped Proceed to
0 times A
2 times B




A

24.INSPECT STARTER INRUSH CURRENT REDUCTION RELAY

B

27.INSPECT STARTER ASSEMBLY
24.INSPECT STARTER INRUSH CURRENT REDUCTION RELAY
a.
A315773C02
2.479,1.781 3,2.25 3,2.25 3,2.417 true 2.385,1.24 2.667,0.667 2.667,0.667 2.833,0.667 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 2.875,0.604 3.188,0.802 0.313,0.198 10 false *a 2.938,2.469 3.25,2.667 0.313,0.198 10 false *b
*1 Starter Assembly
*a B Terminal
*b M Terminal


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect terminals B and M of the starter inrush current reduction relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B Terminal - M Terminal Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

25.INSPECT STARTER ASSEMBLY (C TERMINAL)

NG

26.INSPECT STARTER ASSEMBLY (M TERMINAL)
25.INSPECT STARTER ASSEMBLY (C TERMINAL)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A315774C02
2.24,1.135 2.5,0.583 2.5,0.583 2.583,0.583 true 1.719,1.177 0.917,0.75 0.917,0.75 0.75,0.75 true 2.406,1.302 2.917,1.25 true 0.104,0.135 0.417,0.333 0.313,0.198 10 false *1 2.625,0.531 2.938,0.729 0.313,0.198 10 false *a 0.552,0.698 0.865,0.896 0.313,0.198 10 false *b 2.969,1.177 3.281,1.375 0.313,0.198 10 false *c
*1 Starter Assembly
*a Inspect Part
*b C Terminal
*c B Terminal


Disconnect terminal B of the starter inrush current reduction relay.


c.

Disconnect terminal C of the starter assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C Terminal - B Terminal Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.INSPECT STARTER ASSEMBLY (M TERMINAL)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A315775C02
2.115,1.688 2.75,2.667 2.75,2.667 2.917,2.667 true 2.5,1.74 2.917,1.75 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 2.979,2.594 3.292,2.792 0.313,0.198 10 false *a 2.99,1.698 3.302,1.896 0.313,0.198 10 false *b
*1 Starter Assembly
*a Inspect Part
*b M Terminal


Disconnect terminal M of the starter inrush current reduction relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M Terminal - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STARTER INRUSH CURRENT REDUCTION RELAY

NG

27.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

28.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)
A348463C17
0.958,0.5 1.302,0.76 0.344,0.26 3.396,0.5 3.74,0.76 0.344,0.26 5.813,0.51 6.26,0.813 0.448,0.302 0.365,2.073 0.719,1.563 true 0.906,2.052 0.74,1.75 true 2.438,2.094 2.604,1.708 true 5.542,2.063 5.771,1.771 true 6.354,2.052 6.198,1.771 true 0.323,0.115 0.635,0.313 0.313,0.198 10 false *a 1.01,0.552 1.323,0.75 0.313,0.198 10 false A86 3.448,0.563 3.76,0.76 0.313,0.198 10 false A66 5.906,0.583 6.438,0.781 0.531,0.198 10 false G87 0.844,2.104 1.156,2.302 0.313,0.198 10 false BIN1 0.229,2.104 0.542,2.302 0.313,0.198 10 false BIN2 2.323,2.115 2.635,2.313 0.313,0.198 10 false +B 6.292,2.083 6.604,2.281 0.313,0.198 10 false IG1 5.427,2.094 5.74,2.292 0.313,0.198 10 false IG2
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -


a.

Disconnect the engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-1 (BIN2) - Body ground Always 9.5 to 14 V
A86-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
G87-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V
G87-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the A86 and A66 engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-2 (GND2) - Body ground Always Below 1 Ω
A86-8 (GND1) - Body ground Always Below 1 Ω
A66-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.READ VALUE USING GTS (CLUTCH LOWER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Clutch Lower SW


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display
Clutch Lower SW
50003 227 11
OK:
Tester Display Condition Normal Condition
Clutch Lower SW Fully Depressed ON
Fully Released OFF



Result:
Result Proceed to
Data Monitor display is not within standards A
Data Monitor display is within standards (w/o Entry and Start System) B
Data Monitor display is within standards (w/ Entry and Start System) C



A

31.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

B

34.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

C

37.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)
31.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)
a.

Inspect the clutch start switch assembly (for lower).

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/o Smart Entry and Start System) A
OK (w/ Smart Entry and Start System) B
NG C



A

32.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)

B

33.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

C

REPLACE CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

32.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the A66 engine stop and start ECU connectors.


b.

Disconnect the G4 ignition or starter switch assembly connector.


c.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - ST NO. 1 relay terminal 2 Fully Depressed Below 1 Ω
Fully Released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - ST NO. 1 relay terminal 2 Fully Depressed Below 1 Ω
Fully Released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>3ZR-FAE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

35.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

35.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)
a.

Disconnect the G4 ignition or starter switch assembly connector.


b.
A316828C05
0.5,1.083 0.917,1.333 0.417,0.25 2.198,1.063 2.635,0.708 true 0.24,0.156 0.552,0.354 0.313,0.198 10 false *a 2.708,0.615 3.021,0.813 0.313,0.198 10 false AM2 0.594,1.135 0.906,1.333 0.313,0.198 10 false G4
*a Front view of wire harness connector
(to Ignition or Starter Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G4-4 (AM2) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

36.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY (FOR LOW))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY (FOR LOW))
a.

Disconnect the G4 ignition or starter switch assembly connector.


b.

Disconnect the A66 engine stop and start ECU connector.


c.

Disconnect the A4 clutch start switch assembly (for low) connector.


d.

Disconnect the A62 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - A4-2 Always Below 1 Ω
G4-2 (ST2) - Body ground Always 10 kΩ or higher
A4-2 - Body ground Always 10 kΩ or higher
A66-17 (CLL) - Body ground Always 10 kΩ or higher
A62-23 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)
a.

Disconnect the A4 clutch start switch assembly (for low) connector.


b.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the A66 engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - A66-17 (CLL) Always Below 1 Ω
G82-5 (STAR) - Body ground Always 10 kΩ or higher
A66-17 (CLL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

38.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)
a.
A342958C23
0.083,0.75 0.438,1.052 0.354,0.302 1.021,1.99 1.281,1.781 true 0.24,0.146 0.552,0.344 0.313,0.198 10 false *a 0.135,0.813 0.594,1.01 0.458,0.198 10 false A66 0.771,1.979 1.229,2.177 0.458,0.198 10 false CLL
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-17 (CLL) - Body ground Engine started using push start switch assembly (ignition switch turned START) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

39.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

40.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)
a.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A4 clutch start switch assembly (for lower) connector.


c.

Disconnect the A66 engine stop and start ECU connector.


d.

Remove the ST NO. 1 relay from the No. 2 engine room relay block and junction block assembly.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
A66-21 (STA) - Body ground Always 10 kΩ or higher
ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

41.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG