Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047060 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type)  Reverse Signal Circuit  


DESCRIPTION

The clearance warning ECU assembly receives a reverse shift position signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: except Manual Transaxle

*2: for Manual Transaxle


WIRING DIAGRAM

E270560E06
0.094,0.073 2.375,0.281 2.281,0.208 12 false except Manual Transaxle: 5.292,2.083 6.479,2.469 1.188,0.385 10 false Clearance Warning ECU Assembly 5.281,1.896 5.74,2.094 0.458,0.198 10 false G33 5.417,1.083 5.729,1.281 0.313,0.198 10 false RL 5.177,0.969 5.49,1.167 0.313,0.198 10 false 21 3.188,1.635 4.167,1.833 0.979,0.198 10 false B36*1, B101*2 3.219,1.844 4.604,2.219 1.385,0.375 10 false Park/Neutral Position Switch Assembly 2.073,1.313 2.844,1.51 0.771,0.198 10 false GAUGE 4.396,0.979 4.552,1.177 0.156,0.198 10 false 2 3.26,0.99 3.417,1.188 0.156,0.198 10 false 1 0.396,1.073 1.396,1.292 1,0.219 10 false IG1 NO.2 Relay 0.229,2.208 1.958,2.365 1.729,0.156 10 false *1: except 3ZR-FE, 2AR-FE 0.24,2.438 1.875,2.604 1.635,0.167 10 false *2: for 3ZR-FE, 2AR-FE 3.5,1.083 3.781,1.271 0.281,0.188 10 false RB 4.104,1.094 4.333,1.271 0.229,0.177 10 false RL

E270560E02
0.094,0.073 1.906,0.323 1.813,0.25 12 for Manual Transaxle: 5.292,2.083 6.479,2.469 1.188,0.385 10 Clearance Warning ECU Assembly 5.281,1.896 5.74,2.094 0.458,0.198 10 G33 5.417,1.083 5.729,1.281 0.313,0.198 10 RL 5.177,0.969 5.49,1.167 0.313,0.198 10 21 3.229,1.646 3.688,1.844 0.458,0.198 10 B35 3.24,1.844 4.563,2.219 1.323,0.375 10 Back-up Light Switch Assembly 2.073,1.313 2.844,1.51 0.771,0.198 10 GAUGE 4.396,0.979 4.552,1.177 0.156,0.198 10 1 3.26,0.99 3.417,1.188 0.156,0.198 10 2 0.396,1.073 1.396,1.292 1,0.219 10 IG1 NO.2 Relay

PROCEDURE

1.CHECK CLEARANCE WARNING ECU ASSEMBLY (REVERSE SIGNAL)
a.

Disconnect the G33 clearance warning ECU assembly connector.


b.
E270561C02
1.49,0.208 1.906,0.479 0.417,0.271 1.74,1.771 2.104,1.177 false 0.104,0.063 0.417,0.26 0.313,0.198 10 *a 1.563,0.26 1.906,0.448 0.344,0.188 10 G33 1.521,1.698 1.833,1.896 0.313,0.198 10 RL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G33-21 (RL) - Body ground Ignition switch ON
Shift lever in R
11 to 14 V
G33-21 (RL) - Body ground Ignition switch ON
Shift lever in any position except R
Below 1 V



Result:
Result
OK
NG (except Manual Transaxle)
NG (for Manual Transaxle)



OK

NG (except Manual Transaxle)

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG (for Manual Transaxle)

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G33 clearance warning ECU assembly connector.


b.

Disconnect the B36*1 or B101*2 park/neutral position switch assembly connector.

*1: except 3ZR-FE, 2AR-FE


*2: for 3ZR-FE, 2AR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except 3ZR-FE, 2AR-FE
Tester Connection Condition Specified Condition
G33-21 (RL) - B36-2 (RL) Always Below 1 Ω
G33-21 (RL) - Body ground Always 10 kΩ or higher


for 3ZR-FE, 2AR-FE
Tester Connection Condition Specified Condition
G33-21 (RL) - B101-2 (RL) Always Below 1 Ω
G33-21 (RL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G33 clearance warning ECU assembly connector.


b.

Disconnect the B35 back-up light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-21 (RL) - B35-1 Always Below 1 Ω
G33-21 (RL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR