The 4WD ECU assembly outputs this DTC if a difference in tire size is detected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1337/91 | Diameter of the Tire is not Uniform | When the following continues for 36 seconds or more:
At a vehicle speed of 30 km/h (18.6 mph) or more, the average speed difference between the front wheel and rear wheel is 4% or more. |
·
Tire size or pressure (front and rear tires) ·
Speed sensor circuit ·
Front speed sensor ·
Rear speed sensor ·
Front speed sensor rotor (Front axle hub sub-assembly) ·
Rear speed sensor rotor (Rear axle hub and bearing assembly) ·
Harness and connector ·
Skid control ECU (Brake actuator assembly) ·
4WD ECU assembly |
Check the condition of each related circuit connector before troubleshooting.
Check the size and condition of all 4 tires.
This DTC is output when tire deformation or a difference in tire size is detected.
The diameter and air pressure of all 4 tires are the same.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more so that the same DTC is output.
Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR
Check if the speed sensor DTC (brake control system DTC) is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| Only "C1377/91" is output | A |
| DTC is not output | B |
| Speed sensor DTC (brake control system DTC) is output | C |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
C
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Turn the power switch off.
Disconnect the A100 skid control ECU (brake actuator assembly) connector.
Disconnect the A14, A43, M20 and/or N11 speed sensor connector(s).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A100-31 (FR+) - A43-1 (FR+) | Always | Below 1 Ω |
| A100-31 (FR+) or A43-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| A100-30 (FR-) - A43-2 (FR-) | Always | Below 1 Ω |
| A100-30 (FR-) or A43-2 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A100-18 (FL+) - A14-1 (FL+) | Always | Below 1 Ω |
| A100-18 (FL+) or A14-1 (FL+) - Body ground | Always | 10 kΩ or higher |
| A100-17 (FL-) - A14-2 (FL-) | Always | Below 1 Ω |
| A100-17 (FL-) or A14-2 (FL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A100-16 (RR+) - M20-1 (RR+) | Always | Below 1 Ω |
| A100-16 (RR+) or M20-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| A100-15 (RR-) - M20-2 (RR-) | Always | Below 1 Ω |
| A100-15 (RR-) or M20-2 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A100-29 (RL+) - N11-1 (RL+) | Always | Below 1 Ω |
| A100-29 (RL+) or N11-1 (RL+) - Body ground | Always | 10 kΩ or higher |
| A100-28 (RL-) - N11-2 (RL-) | Always | Below 1 Ω |
| A100-28 (RL-) or N11-2 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Tester Display |
|---|
| Signal Check |
All Test Mode DTCs are cleared.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.
Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC is output |
| DTC is not output |
DTC is output
DTC is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Remove the front speed sensor rotor (front axle hub sub-assembly) or rear speed sensor rotor (rear axle hub and bearing assembly).
For front: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL
For rear: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL
Check the speed sensor rotor.
No scratches, oil, or foreign matter on the rotors.
Check the speed sensor signal after cleaning or replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly.
If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Replace the front speed sensor or the rear speed sensor.
For front: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
For rear: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for 4WD/AWD)>REMOVAL
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTC.
Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.
Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC is output |
| DTC is not output |
Reinstall the sensor, connectors, etc. and restore the vehicle to its prior condition before rechecking DTCs.
DTC is output
DTC is not output
Replace the brake actuator assembly.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTC.
Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.
Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC is output |
| DTC is not output |
DTC is output
DTC is not output