The AUTO LSD is a system for 2WD vehicles. When the VSC OFF switch (telltale light assembly) is pushed on, the AUTO LSD function is available and the AUTO LSD indicator light illuminates.
The AUTO LSD does not operate even if the VSC OFF switch (telltale light assembly) is pressed under the following conditions:
The TRC/TRAC or VSC system is faulty.
The temperature inside the brake actuator assembly increases and the AUTO LSD operation is suspended.
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if CAN communication system DTCs are output.
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
| Proceed to |
|---|
| DTC is not output |
| DTC is output (for LHD with Central Gateway ECU) |
| DTC is output (for RHD with Central Gateway ECU) |
| DTC is output (for LHD without Central Gateway ECU) |
| DTC is output (for RHD without Central Gateway ECU) |
DTC is not output
DTC is output (for LHD with Central Gateway ECU)
DTC is output (for RHD with Central Gateway ECU)
DTC is output (for LHD without Central Gateway ECU)
DTC is output (for RHD without Central Gateway ECU)
Turn the ignition switch off.
Disconnect the A100 skid control ECU (brake actuator assembly) connector.
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A100-33 (CSW) - Body ground | VSC OFF switch (telltale light assembly) held on | Below 1 Ω |
| VSC OFF switch (telltale light assembly) off (Not pressed) | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A100 skid control ECU (brake actuator assembly) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Auto LSD Indicator Light | AUTO LSD indicator light | ON or OFF | OFF: AUTO LSD indicator light off
ON: AUTO LSD indicator light on |
for 2WD |
| Tester Display |
|---|
| Auto LSD Indicator Light |
Check the GTS display condition of the AUTO LSD indicator light.
| Proceed to |
|---|
| Display of the Data List remains OFF |
| Display of the Data List remains ON |
Display of the Data List remains OFF
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Display of the Data List remains ON
Remove the VSC OFF switch (telltale light assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL
Inspect the VSC OFF switch (telltale light assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A100-33 (CSW) - G43-6 (+) | Always | Below 1 Ω |
| G43-13 (E) - Body ground | Always | Below 1 Ω |
| A100-33 (CSW) or G43-6 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG