Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for HV Model with Occupant Classification System)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0369991 AIRBAG SYSTEM(for HV Model with Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for HV Model with Occupant Classification System)  B1810  Short in D Squib (Dual Stage - 2nd Step) Circuit  B1811  Open in D Squib (Dual Stage - 2nd Step) Circuit  B1812  Short in D Squib (Dual Stage - 2nd Step) Circuit (to Ground)  B1813  Short in D Squib (Dual Stage - 2nd Step) Circuit (to +B)  


DESCRIPTION

The driver side squib 2nd step circuit consists of the airbag sensor assembly, spiral with sensor cable sub-assembly and horn button assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib 2nd step circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1810 Short in D Squib (Dual Stage - 2nd Step) Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the driver side squib 2nd step circuit during the primary check.

·

A horn button assembly (driver side squib 2nd step) malfunction.

·

A spiral with sensor cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Spiral with sensor cable sub-assembly

·

Horn button assembly (driver side squib 2nd step)

·

Airbag sensor assembly


Comes on Applicable
B1811 Open in D Squib (Dual Stage - 2nd Step) Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the driver side squib 2nd step circuit for 2 seconds.

·

A horn button assembly (driver side squib 2nd step) malfunction.

·

A spiral with sensor cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Spiral with sensor cable sub-assembly

·

Horn button assembly (driver side squib 2nd step)

·

Airbag sensor assembly


Comes on Applicable
B1812 Short in D Squib (Dual Stage - 2nd Step) Circuit (to Ground) One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the driver side 2nd step circuit for 0.5 seconds.

·

A horn button assembly (driver side squib 2nd step) malfunction.

·

A spiral with sensor cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Spiral with sensor cable sub-assembly

·

Horn button assembly (driver side squib 2nd step)

·

Airbag sensor assembly


Comes on Applicable
B1813 Short in D Squib (Dual Stage - 2nd Step) Circuit (to +B) One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds.

·

A horn button assembly (driver side squib 2nd step) malfunction.

·

A spiral with sensor cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Spiral with sensor cable sub-assembly

·

Horn button assembly (driver side squib 2nd step)

·

Airbag sensor assembly


Comes on Applicable

WIRING DIAGRAM

C238833E58
5.25,1.208 5.396,1.354 0.146,0.146 10 false 8 5.24,0.396 5.344,0.542 0.104,0.146 10 false 9 3.073,0.396 3.177,0.542 0.104,0.146 10 false 4 3.073,1.219 3.177,1.365 0.104,0.146 10 false 3 1.99,1.229 2.094,1.375 0.104,0.146 10 false 1 1.99,0.396 2.094,0.542 0.104,0.146 10 false 2 5.448,0.479 5.781,0.646 0.333,0.167 10 false D2+ 5.448,1.323 5.948,1.51 0.5,0.188 10 false D2- 2.698,0.396 3.219,0.583 0.521,0.188 10 false D2+ 2.729,1.219 3.208,1.427 0.479,0.208 10 false D2- 5.333,1.729 7.146,1.896 1.813,0.167 10 false G70 2,1.708 2.365,1.875 0.365,0.167 10 false G21 2,1.844 3.521,2.167 1.521,0.323 10 false Spiral with Sensor Cable Sub-assembly 0.083,1.719 1.906,2.042 1.823,0.323 10 false z4 5.344,1.885 7.156,2.135 1.813,0.25 10 false Airbag Sensor Assembly 0.094,1.875 1.917,2.198 1.823,0.323 10 false Horn Button Assembly (Driver Side Squib 2nd Step)

CAUTION / NOTICE / HINT

NOTICE:
·

When installing the spiral with sensor cable sub-assembly and steering wheel, be sure to adjust the spiral with sensor cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK CONNECTORS
a.
C371112C03
0.198,0.813 0.51,1.01 0.313,0.198 10 false *1 1.052,1.375 1.365,1.573 0.313,0.198 10 false *3 2.781,1.583 3.094,1.781 0.313,0.198 10 false *2 1.979,0.823 2.292,1.021 0.313,0.198 10 false *4
*1 Horn Button Assembly (Driver Side Squib 2nd Step)
*2 Airbag Sensor Assembly
*3 Spiral with Sensor Cable Sub-assembly
*4 Instrument Panel Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the horn button assembly (driver side squib 2nd step), spiral with sensor cable sub-assembly and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the horn button assembly (driver side squib 2nd step), spiral with sensor cable sub-assembly and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the spiral with sensor cable sub-assembly connector (on the horn button assembly (driver side squib 2nd step) side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and spiral with sensor cable sub-assembly connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB 2ND STEP)

NG

REPLACE INSTRUMENT PANEL WIRE OR SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

2.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB 2ND STEP)
a.
C411565C01
0.333,2.115 0.688,2.333 0.354,0.219 1.479,2.698 1.688,2.885 1.688,2.885 1.833,2.885 true 1.719,2.229 1.885,2.146 1.885,2.146 1.99,2.146 true 2.344,0.615 2.656,0.771 0.313,0.156 10 false A 0.292,0.865 0.604,1.021 0.313,0.156 10 false *1 2.719,1.281 3.031,1.438 0.313,0.156 10 false *2 1.177,1 1.49,1.156 0.313,0.156 10 false *3 2.042,2.052 2.354,2.208 0.313,0.156 10 false *4 0.365,1.719 0.677,1.875 0.313,0.156 10 false *a 1.906,2.813 2.219,2.969 0.313,0.156 10 false *b 2.188,0.615 2.5,0.771 0.313,0.156 10 false B 1.76,0.625 2.073,0.781 0.313,0.156 10 false C 1.594,0.625 2.104,0.771 0.51,0.146 10 false D 0.76,0.625 1.271,0.771 0.51,0.146 10 false E 0.438,0.625 0.948,0.771 0.51,0.146 10 false F 0.427,2.125 0.74,2.281 0.313,0.156 10 false z4
*1 Horn Button Assembly (Driver Side Squib 2nd Step)
*2 Airbag Sensor Assembly
*3 Spiral with Sensor Cable Sub-assembly
*4 SST
*a Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib 2nd Step))
*b Color: Black


Connect the instrument panel wire to the airbag sensor assembly and spiral with sensor cable sub-assembly.


b.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

CAUTION:

Never connect the tester to the horn button assembly (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTCs B1810, B1811, B1812 and B1813 are not output
DTC B1810, B1811, B1812 or B1813 is output


HINT:

Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


k.

Disconnect SST from connector E.



DTCs B1810, B1811, B1812 and B1813 are not output

DTC B1810, B1811, B1812 or B1813 is output

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
a.
C411566C01
0.49,2.198 0.813,2.438 0.323,0.24 1.802,2.604 1.552,2.385 false 0.198,0.354 0.583,0.75 0.385,0.396 10 false *1 2.844,1.125 3.26,1.521 0.417,0.396 10 false *2 1.135,0.896 1.552,1.365 0.417,0.469 10 false *3 0.271,1.635 0.656,2.031 0.385,0.396 10 false *a 1.854,2.563 2.25,2.927 0.396,0.365 10 false *b 2.531,0.552 2.948,1.021 0.417,0.469 10 false A 2.219,0.552 2.635,1.021 0.417,0.469 10 false B 1.76,0.552 2.177,1.021 0.417,0.469 10 false C 1.615,0.552 2.031,1.021 0.417,0.469 10 false D 0.781,0.552 1.198,1.021 0.417,0.469 10 false E 0.448,0.552 0.865,1.021 0.417,0.469 10 false F 0.573,2.24 0.99,2.708 0.417,0.469 10 false z4
*1 Horn Button Assembly (Driver Side Squib 2nd Step)
*2 Airbag Sensor Assembly
*3 Spiral with Sensor Cable Sub-assembly
*a Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib 2nd Step))
*b Color: Black
V100135

Release the activation prevention mechanism


Disconnect the instrument panel wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z4-1 - Body ground Power switch on (IG) Below 1 V
z4-2 - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.



c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z4-1 - z4-2 Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z4-1 - Body ground Always 1 MΩ or higher
z4-2 - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z4-1 - z4-2 Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C238334C10
0.177,1.229 0.646,1.49 0.469,0.26 10 false *1 2.75,1.667 3.302,2.042 0.552,0.375 10 false *2 1.052,1.438 1.365,1.781 0.313,0.344 10 false *3
*1 Horn Button Assembly (Driver Side Squib 2nd Step)
*2 Airbag Sensor Assembly
*3 Spiral with Sensor Cable Sub-assembly


Connect the connectors to the horn button assembly (driver side squib 2nd step) and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTCs B1810, B1811, B1812 and B1813 are not output
DTC B1810, B1811, B1812 or B1813 is output


HINT:

Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.




DTCs B1810, B1811, B1812 and B1813 are not output

DTC B1810, B1811, B1812 or B1813 is output

5.CHECK INSTRUMENT PANEL WIRE
a.
C375414C11
0.438,2.365 0.844,2.615 0.406,0.25 0.927,3.042 1.073,3.042 1.073,3.042 1.542,2.604 true 1.896,2.917 1.781,2.917 1.781,2.917 1.698,2.625 true 0.135,0.635 0.448,0.833 0.313,0.198 10 false *1 2.74,1.479 3.052,1.677 0.313,0.198 10 false *2 1.042,1.167 1.354,1.365 0.313,0.198 10 false *3 1.885,0.583 2.198,0.781 0.313,0.198 10 false *4 0.375,1.969 0.688,2.167 0.313,0.198 10 false *a 0.625,2.969 1.052,3.156 0.427,0.188 10 false D2- 1.979,2.844 2.333,3.042 0.354,0.198 10 false D2+ 2.385,0.813 2.698,1.01 0.313,0.198 10 false A 2.115,0.823 2.427,1.021 0.313,0.198 10 false B 1.76,0.823 2.073,1.021 0.313,0.198 10 false C 1.5,0.823 1.813,1.021 0.313,0.198 10 false D 0.677,0.813 0.99,1.01 0.313,0.198 10 false E 0.406,0.813 0.719,1.01 0.313,0.198 10 false F 0.531,2.406 1.073,2.635 0.542,0.229 10 false G21
*1 Horn Button Assembly (Driver Side Squib 2nd Step)
*2 Airbag Sensor Assembly
*3 Spiral with Sensor Cable Sub-assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)
V100135

Release the activation prevention mechanism


Disconnect the instrument panel wire from the spiral with sensor cable sub-assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G21-4 (D2+) - Body ground Power switch on (IG) Below 1 V
G21-3 (D2-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.



c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G21-4 (D2+) - G21-3 (D2-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G21-4 (D2+) - Body ground Always 1 MΩ or higher
G21-3 (D2-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G21-4 (D2+) - G21-3 (D2-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE