The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during horn button assembly removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
Be sure to read precaution thoroughly before servicing.
w/o Occupant Classification System:
for Gasoline Model with Occupant Classification System:
for HV Model with Occupant Classification System:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
2.REMOVE DECK BOARD ASSEMBLY (for HV Model)
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
65351A
4.REMOVE BATTERY HOLE COVER (for HV Model)
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
45130
6.REMOVE HORN BUTTON ASSEMBLY
|
Deployment Side |
When storing the horn button assembly, keep the airbag deployment side facing upward.
If the airbag deploys for any reason, it may cause a serious accident.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
|
Release in this Direction |
Using a screwdriver, insert it from the hole of the steering wheel assembly and push the torsion spring to detach the pin.
| *a | Lock Button |
| *b | Wire Harness Clamp |
|
Airbag Connector |
|
Horn Connector |
|
Release in this Direction |
|
Protective Tape |
for Dual Type:
Tilt the horn button assembly toward the seat and support it with one hand.
Do not drop the horn button assembly.
When disconnecting the horn button assembly, do not pull the airbag wire harness.
Using a screwdriver, release the lock button and disconnect the 2 airbag connectors.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Tape the screwdriver tip before use.
Detach the wire harness clamp and disconnect the horn connector.
| *a | Lock Button |
| *b | Wire Harness Clamp |
|
Airbag Connector |
|
Horn Connector |
|
Release in this Direction |
|
Protective Tape |
for Single Type:
Tilt the horn button assembly toward the seat and support it with one hand.
Do not drop the horn button assembly.
When disconnecting the horn button assembly, do not pull the airbag wire harness.
Using a screwdriver, release the lock button and disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Tape the screwdriver tip before use.
Detach the wire harness clamp and disconnect the horn connector.