Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM3620E _58 Vehicle Interior _076046 DOOR LOCK _0370163 POWER DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  B1243  GSW Terminal Circuit Malfunction  


DESCRIPTION

If the collision door lock release function does not operate normally, or an open or short in the GSW input circuit of the main body ECU (multiplex network body ECU) is detected, DTC B1243 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1243 GSW Terminal Circuit Malfunction A malfunction occurs in the GSW input circuit of the main body ECU (multiplex network body ECU).
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Airbag sensor assembly

·

Harness or connector



WIRING DIAGRAM

B345030E68
1.25,0.938 1.708,1.135 0.458,0.198 10 false GSW 1.667,0.833 1.979,1.031 0.313,0.198 10 false 25 0.583,1.802 1.042,2 0.458,0.198 10 false G70 0.594,1.969 2.51,2.344 1.917,0.375 10 false Airbag Sensor Assembly 5.646,0.938 6.104,1.135 0.458,0.198 10 false GSW 4.427,0.823 4.74,1.021 0.313,0.198 10 false 7 5.406,0.823 5.719,1.021 0.313,0.198 10 false 24 4.01,1.292 4.323,1.49 0.313,0.198 10 false 4A 4.01,1.438 5.563,1.813 1.552,0.375 10 false Instrument Panel Junction Block Assembly 5.344,1.802 5.656,2 0.313,0.198 10 false A 5.344,1.979 7,2.531 1.656,0.552 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*

*: w/ Entry and Start System

·

When DTC B1243 is output, the collision door lock release, shift-linked automatic door lock/unlock and speed-sensitive automatic door lock functions are prohibited.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

for HV Model with Occupant Classification System:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>PRECAUTION

for Gasoline Model with Occupant Classification System:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>PRECAUTION

w/o Occupant Classification System:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>PRECAUTION



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1243 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
B473154C09
1.406,0.135 1.885,0.406 0.479,0.271 1.927,1.25 2.396,0.667 2.396,0.667 2.51,0.667 false 1.51,0.208 1.823,0.406 0.313,0.198 10 false G70 2.583,0.625 3.021,0.823 0.438,0.198 10 false GSW 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

Turning the ignition switch to ON with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.




c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G70-25 (GSW) - Body ground Ignition switch ON 4.3 to 5.5 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Disconnect the 4A instrument panel junction block assembly connector.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-7 - G70-25 (GSW) Always Below 1 Ω
4A-7 or G70-25 (GSW) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B472615C07
1.771,0.625 2.271,0.917 0.5,0.292 5.354,0.625 5.854,0.917 0.5,0.292 2.375,2.125 2.51,2.125 2.51,2.125 2.969,1.573 false 5.51,0.698 5.75,0.896 0.24,0.198 10 false 4A 2.01,0.708 2.167,0.906 0.156,0.198 10 false A 2.01,2.042 2.469,2.292 0.458,0.25 10 false GSW 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-24 (GSW) - 4A-7 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG