Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM3620E _58 Vehicle Interior _076046 DOOR LOCK _0370163 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Key Cylinder  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives door key cylinder lock or unlock switch signals from the front door with motor lock assembly (for Driver Door). The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B494156E06
0.677,2.646 2.865,3.021 2.188,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.667,2.469 1.125,2.667 0.458,0.198 10 false G45 4.385,2.292 5.573,2.5 1.188,0.208 10 false J10*1, I11*2 4.375,2.448 6.563,2.823 2.188,0.375 10 false Front Door with Motor Lock Assembly (for Driver Door) 1.938,1.125 2.396,1.323 0.458,0.198 10 false L2 1.865,1.813 2.323,2.01 0.458,0.198 10 false UL3 4.75,1.146 5.208,1.344 0.458,0.198 10 false L 4.052,1.802 5.031,2 0.979,0.198 10 false 10*1, 5*2 4.042,1.135 5.031,1.438 0.99,0.302 10 false 9*1, 6*2 4.729,1.802 5.188,2.042 0.458,0.24 10 false UL 5.698,1.49 6.156,1.729 0.458,0.24 10 false E 5.927,1.479 6.75,1.698 0.823,0.219 10 false 7*1, 8*2 2.188,1.115 2.646,1.354 0.458,0.24 10 false 18 2.188,1.792 2.646,2.031 0.458,0.24 10 false 17 1.167,0.875 1.625,1.073 0.458,0.198 10 false +B 1.167,1.542 1.625,1.74 0.458,0.198 10 false +B 0.25,3.427 1.438,3.635 1.188,0.208 10 false *1: for LHD 1.271,3.427 2.458,3.635 1.188,0.208 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*

*: w/ Entry and Start System


PROCEDURE

1.READ VALUE USING GTS (Door Key SW-Lock, D Door Key SW-UL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver door key-linked switch lock signal OFF or ON OFF: Driver door key cylinder not turned to lock position
ON: Driver door key cylinder turned to lock position
-
D Door Key SW-UL Driver door key-linked switch unlock signal OFF or ON OFF: Driver door key cylinder not turned to unlock position
ON: Driver door key cylinder turned to unlock position
-
Body Electrical > Main Body > Data List
Tester Display
Door Key SW-Lock
D Door Key SW-UL
50003 123 19,21
OK:

On the GTS screen, ON or OFF is displayed for each item according to the table above.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Door)
2.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Door)
a.

Remove the front door with motor lock assembly (for Driver Door).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.

Inspect the front door with motor lock assembly (for Driver Door).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Door) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

REPLACE FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Door)

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR WITH MOTOR LOCK ASSEMBLY (for Driver Door) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the J10*1 or I11*2 front door with motor lock assembly (for Driver Door) connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G45 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
J10-9 (L) - G45-18 (L2) Always Below 1 Ω
J10-10 (UL) - G45-17 (UL3) Always Below 1 Ω
J10-7 (E) - Body ground Always Below 1 Ω
J10-9 (L) or G45-18 (L2) - Other terminals and body ground Always 10 kΩ or higher
J10-10 (UL) or G45-17 (UL3) - Other terminals and body ground Always 10 kΩ or higher


Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
I11-6 (L) - G45-18 (L2) Always Below 1 Ω
I11-5 (UL) - G45-17 (UL3) Always Below 1 Ω
I11-8 (E) - Body ground Always Below 1 Ω
I11-6 (L) or G45-18 (L2) - Other terminals and body ground Always 10 kΩ or higher
I11-5 (UL) or G45-17 (UL3) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR