In some cases, wireless door lock control functions are normal but the hazard warning light answer-back function does not operate. In such cases, hazard warning light signal output from the main body ECU (multiplex network body ECU) may be malfunctioning.
The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication system is functioning properly.
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Customize Setting / Wireless Door Lock.
Select the setting by referring to the table below.
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Hazard Answer Back | Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation* | ON | 0:OFF,1:ON | Main body ECU (Multiplex network body ECU) |
*: for the vehicles displaying the Item "Hazard Answer Back" on the GTS
| Proceed to |
|---|
| Customize setting is ON |
| Customize setting is OFF |
Customize setting is ON
Customize setting is OFF
Check the wireless door lock control function using the door control transmitter module set sub-assembly.
| Proceed to |
|---|
| Wireless door lock/unlock operates properly |
| Wireless door lock/unlock does not operate properly |
Wireless door lock/unlock operates properly
Wireless door lock/unlock does not operate properly
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Pos | Front door RH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door RH locked
UNLOCK: Front door RH unlocked |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door LH locked
UNLOCK: Front door LH unlocked |
- |
| RR-Door Lock Pos SW | Rear door RH unlock detection switch signal*1 | OFF or ON | OFF: Rear door RH locked*1
ON: Rear door RH unlocked*1 |
- |
| RL-Door Lock Pos SW | Rear door LH unlock detection switch signal*1
Rear door RH and LH unlock detection switch signal*2 |
OFF or ON | OFF: Rear door LH locked*1
OFF: Rear door RH and LH locked*2 ON: Rear door LH unlocked*1 ON: Rear door RH or LH unlocked*2 |
- |
| Tester Display |
|---|
| FR Door Lock Pos |
| FL Door Lock Pos |
| RR-Door Lock Pos SW |
| RL-Door Lock Pos SW |
*1: w/ Memory Call Function
*2: w/o Memory Call Function
The GTS display changes correctly in response to the lock/unlock operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the hazard warning lights blink when the hazard warning signal switch is pressed.
Hazard warning lights blink.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG