The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.
w/ Memory Call Function:
w/o Memory Call Function:
w/ Entry and Start System:
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Read the Data List according to the display on the GTS.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Pos | Front door RH unlock detection switch signal | UNLOCK or LOCK | UNLOCK: Front door RH unlocked
LOCK: Front door RH locked |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal | UNLOCK or LOCK | UNLOCK: Front door LH unlocked
LOCK: Front door LH locked |
- |
| RR-Door Lock Pos SW | Rear door RH unlock detection switch signal*1
Rear door RH and rear door LH unlock detection switch signal*2 |
OFF or ON | OFF: Rear door RH unlocked*1
OFF: Rear door RH and rear door LH unlocked*2 ON: Rear door RH locked*1 ON: Rear door RH or rear door LH locked*2 |
- |
| RL-Door Lock Pos SW | Rear door LH unlock detection switch signal*1
Rear door LH and rear door RH unlock detection switch signal*2 |
OFF or ON | OFF: Rear door LH unlocked*1
OFF: Rear door LH and rear door RH unlocked*2 ON: Rear door LH locked*1 ON: Rear door LH or rear door RH locked*2 |
- |
| Tester Display |
|---|
| FR Door Lock Pos |
| FL Door Lock Pos |
| RR-Door Lock Pos SW |
| RL-Door Lock Pos SW |
*1: w/ Memory Call Function
*2: w/o Memory Call Function
Normal conditions listed above are displayed.
| Result | Proceed to |
|---|---|
| OK | A |
| NG ("FR Door Lock Pos" is abnormal) | B |
| NG ("FL Door Lock Pos" is abnormal) | C |
| NG ("RR-Door Lock Pos SW" is abnormal) (w/ Memory Call Function) | D |
| NG ("RL-Door Lock Pos SW" is abnormal) (w/ Memory Call Function) | E |
| NG ("RR-Door Lock Pos SW" is abnormal) (w/o Memory Call Function) | F |
| NG ("RL-Door Lock Pos SW" is abnormal) (w/o Memory Call Function) |
A
B
C
D
E
F
Remove the front door with motor lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door with motor lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I11 front door with motor lock assembly RH connector.
Disconnect the 4D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I11-7 (LSSR) - 4D-12 | Always | Below 1 Ω |
| I11-8 (E) - Body ground | Always | Below 1 Ω |
| I11-7 (LSSR) or 4D-12 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-12 - A-17 (LSFR) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Remove the front door with motor lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door with motor lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J10 front door with motor lock assembly LH connector.
Disconnect the 4D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J10-8 (LSSR) - 4D-13 | Always | Below 1 Ω |
| J10-7 (E) - Body ground | Always | Below 1 Ω |
| J10-8 (LSSR) or 4D-13 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-13 - A-19 (LSFL) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Remove the rear door with motor lock assembly RH.
Inspect the rear door with motor lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K4 rear door with motor lock assembly RH connector.
Disconnect the G43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-9 (LSSR) - G43-20 (LSWR) | Always | Below 1 Ω |
| K4-10 (E) - Body ground | Always | Below 1 Ω |
| K4-9 (LSSR) or G43-20 (LSWR) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-6 (LSSR) - G43-20 (LSWR) | Always | Below 1 Ω |
| K4-9 (E) - Body ground | Always | Below 1 Ω |
| K4-6 (LSSR) or G43-20 (LSWR) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Remove the rear door with motor lock assembly LH.
Inspect the rear door with motor lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L4 rear door with motor lock assembly LH connector.
Disconnect the 4D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-5 (LSSR) - 4D-14 | Always | Below 1 Ω |
| L4-6 (E) - Body ground | Always | Below 1 Ω |
| L4-5 (LSSR) or 4D-14 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-6 (LSSR) - 4D-14 | Always | Below 1 Ω |
| L4-9 (E) - Body ground | Always | Below 1 Ω |
| L4-6 (LSSR) or 4D-14 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-14 - A-5 (LSWL) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Remove the rear door with motor lock assembly RH.
Inspect the rear door with motor lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear door with motor lock assembly LH.
Inspect the rear door with motor lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L4 rear door with motor lock assembly LH connector.
Disconnect the K4 rear door with motor lock assembly RH connector.
Disconnect the 4D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-5 (LSSR) - 4D-14 | Always | Below 1 Ω |
| L4-6 (E) - Body ground | Always | Below 1 Ω |
| L4-5 (LSSR) or 4D-14 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-6 (LSSR) - 4D-14 | Always | Below 1 Ω |
| L4-9 (E) - Body ground | Always | Below 1 Ω |
| L4-6 (LSSR) or 4D-14 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L4 rear door with motor lock assembly LH connector.
Disconnect the K4 rear door with motor lock assembly RH connector.
Disconnect the 4D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-9 (LSSR) - 4D-14 | Always | Below 1 Ω |
| K4-10 (E) - Body ground | Always | Below 1 Ω |
| K4-9 (LSSR) or 4D-14 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-6 (LSSR) - 4D-14 | Always | Below 1 Ω |
| K4-9 (E) - Body ground | Always | Below 1 Ω |
| K4-6 (LSSR) or 4D-14 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-14 - A-5 (LSWL) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D