Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0370706 AUTOMATIC TRANSAXLE ASSEMBLY A

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.


PROCEDURE

Hide 36100A 1.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT

HINT:

It is not necessary to remove the transfer and transaxle setting stud bolts unless they are being replaced.



b.
C407287C01
1.302,0.688 1.458,0.885 0.156,0.198 10 false - 1.417,3 1.646,3.229 0.229,0.229 10 false *a 1.906,2.542 2.135,2.781 0.229,0.24 10 false *b 0.094,2.927 0.323,3.125 0.229,0.198 10 false *c 0.469,3.104 0.688,3.333 0.219,0.229 10 false *d 3.073,2.656 3.302,2.865 0.229,0.208 10 false *e 1.427,2 1.656,2.229 0.229,0.229 10 false *a
*a 22 mm (0.866 in.)
*b 69 mm (2.72 in.)
*c 5.0 to 7.5 mm (0.200 to 0.300 in.)
*d 13 mm (0.512 in.)
*e 47 mm (1.85 in.)
V100143

Sealant
V100144

Adhesive 1324
V100135

Transfer and Transaxle Setting Stud Bolt A
V100136

Transfer and Transaxle Setting Stud Bolt B


for Automatic Transaxle Assembly Side:

NOTICE:

There are 2 types of transfer assembly installation conditions, a type using only nuts and a type using nuts and bolts.

Install stud bolts according to the transfer assembly installation condition of the vehicle.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>INSTALLATION


i.

Clean the transfer and transaxle setting stud bolt holes.


ii.

for Transfer and Transaxle Setting Stud Bolt A:

1.

Apply adhesive 1324 to 2 or 3 threads on one half of 3 new transfer and transaxle setting stud bolts A as shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:
·

Do not apply adhesive 1324 to the ends of the transfer and transaxle setting stud bolts A.

·

Install the transfer and transaxle setting stud bolts A immediately after applying adhesive 1324 to prevent the adherence of foreign matter.

·

Install the transfer and transaxle setting stud bolts A so that the side that has adhesive 1324 is facing the automatic transaxle assembly.



2.

Install the 3 transfer and transaxle setting stud bolts A to the automatic transaxle assembly positions shown in the illustration.

Torque:

39.2 N*m (400 kgf*cm, 29 ft.*lbf)




iii.

for Transfer and Transaxle Setting Stud Bolt B:

1.

Install a new transfer and transaxle setting stud bolt B to the automatic transaxle assembly positions shown in the illustration.

Torque:

39.2 N*m (400 kgf*cm, 29 ft.*lbf)


NOTICE:

Install the transfer and transaxle setting stud bolt B so that the side that has sealant is facing the automatic transaxle assembly.





Hide 32000 3.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C374401C01
2.25,0.417 2.625,0.146 2.625,0.146 2.771,0.146 true 0.573,0.448 0.719,0.448 0.719,0.448 0.917,0.885 true 2.813,0.021 3.073,0.219 0.26,0.198 10 false *a 0.354,0.344 0.552,0.542 0.198,0.198 10 true *b
*a Matchmark
*b Key


Set the key at the top of the front oil pump drive gear and put a matchmark on the transaxle housing.


b.
C361055C02
1.479,0.188 1.573,0.188 1.573,0.188 1.74,0.688 false 1.729,1.583 2.167,1.906 false 1.281,0.063 1.594,0.26 0.313,0.198 10 false *a 2.229,1.885 2.542,2.083 0.313,0.198 10 false *b
*a Groove
*b Matchmark
V100135

MP Grease


Apply MP grease to place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.


c.
C402826C01
1.302,0.656 0.75,0.333 0.75,0.333 1.302,0.74 true 2.302,1.26 1.583,2 1.583,2 2.302,0.927 true 1.396,2 1.563,2.167 0.167,0.167 10 false *1 0.563,0.229 0.729,0.396 0.167,0.167 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Align the matchmark on the housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




d.
C402827C01
1.302,0.646 1.083,0.25 1.083,0.25 0.917,0.25 true 1.313,1.75 1.083,2.083 1.083,2.083 0.917,2.083 true 2.313,1.24 1.667,2.083 1.667,2.083 2.292,0.958 true 0.719,0.167 0.885,0.333 0.167,0.167 10 false *a 0.719,2 0.885,2.167 0.167,0.167 10 false *a 1.469,2 1.635,2.167 0.167,0.167 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




e.
C402828C01
1.323,0.771 0.833,0.333 0.833,0.333 1.323,0.656 true 2.313,1.24 1.667,2 1.667,2 2.302,0.948 true 1.479,1.969 1.698,2.177 0.219,0.208 10 false *1 0.625,0.219 0.833,0.417 0.208,0.198 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the groove of the torque converter assembly into the key of the oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C374406N02
2.375,0.167 2.552,0.406 0.177,0.24 10 false A

Using a vernier caliper and straightedge, measure the dimension (A) shown in the illustration and check the dimension (A).

Standard:

14 mm (0.5512 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C374400

Install the 4 wire harness clamp brackets to the automatic transaxle case sub-assembly and transmission case side cover with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
C374399

Install the wire harness clamp bracket to the automatic transaxle case sub-assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
C374398

Install the wire harness clamp bracket to the automatic transaxle case sub-assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 35150 5.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Coat a new O-ring with Toyota Genuine ATF WS and install it to the transmission case plug assembly.


b.

Install the transmission case plug assembly to the transaxle housing.


Hide 33823 6.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle case sub-assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33493A 7.INSTALL TRANSMISSION OIL COOLER

Hide 32907C 8.INSTALL NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

Hide 32941 9.CONNECT INLET NO. 1 OIL COOLER HOSE

Hide 32942 10.CONNECT OUTLET NO. 1 OIL COOLER HOSE

Hide 30500 11.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C363764C01
1.698,1.063 1.927,1.063 false 1.167,1 1.479,1.198 0.313,0.198 10 false *1 1.969,0.979 2.281,1.177 0.313,0.198 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz)



b.
C374407C01
0.698,1.49 0.813,1.49 0.813,1.49 1.115,1.073 true 2.802,0.875 2.656,0.875 2.656,0.875 2.156,0.375 true 0.458,1.385 0.656,1.583 0.198,0.198 10 true *1 2.844,0.74 3.042,0.938 0.198,0.198 10 true *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
C402823N01
2.448,0.031 2.604,0.229 0.156,0.198 10 false A 2.865,0.219 3.021,0.417 0.156,0.198 10 false A 1.01,0.042 1.167,0.24 0.156,0.198 10 false B 2.5,1.979 2.656,2.177 0.156,0.198 10 false C 2.823,1.719 2.979,1.917 0.156,0.198 10 false D 1.229,2.01 1.385,2.167 0.156,0.156 10 false D 0.938,1.865 1.073,2.063 0.135,0.198 10 true D 0.771,0.448 0.906,0.646 0.135,0.198 10 false D

While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the automatic transaxle assembly with the 8 bolts shown in the illustration.

Torque:
Bolt (A) : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt (B) : 46 N*m (469 kgf*cm, 34 ft.*lbf)
Bolt (C) : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt (D) : 46 N*m (469 kgf*cm, 34 ft.*lbf)

Bolt Length:
Bolt Length
(A) 50 mm (1.97 in.)
(B) 45 mm (1.77 in.)
(C) 35 mm (1.38 in.)
(D) 45 mm (1.77 in.)


NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the automatic transaxle assembly.

·

When mounting the automatic transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the automatic transaxle assembly are in close contact with one another.




Hide 12303 12.INSTALL REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.

Install the No. 2 rear engine mounting bracket to the rear engine mounting bracket with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
C402825N01
2.198,0.323 2.365,0.49 0.167,0.167 10 true A 2.219,1.51 2.385,1.677 0.167,0.167 10 true B 0.875,1.635 1.042,1.802 0.167,0.167 10 true C 0.708,0.51 0.875,0.677 0.167,0.167 10 true C

Install the rear engine mounting bracket sub-assembly to the transaxle housing with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (A) → Tighten bolt (C)



Hide 12371A 13.INSTALL REAR ENGINE MOUNTING INSULATOR

a.
A429165C01
2.625,2.344 2.813,1.99 2.813,1.99 2.958,1.99 false 2.979,1.896 3.219,2.146 0.24,0.25 10 false *a
*a Rubber Protrusion


Install the rear engine mounting insulator to the rear engine mounting bracket sub-assembly with the bolt and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Align the rubber protrusion of the rear engine mounting insulator with the shape of the rear engine mounting bracket sub-assembly.



b.
C408005C01
1.354,0.115 1.51,0.313 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B


Install the 2 wire harness clamp brackets to the rear engine mounting insulator with the 2 bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 37117 14.INSTALL PROPELLER SHAFT HEAT INSULATOR

a.
C408819C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Install the propeller shaft heat insulator to the automatic transaxle assembly with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Tightening order: Temporarily install bolt (A) → Temporarily install bolt (B) → Tighten bolt (C) → Tighten bolt (B) → Tighten bolt (A)



Hide 12372A 15.INSTALL ENGINE MOUNTING INSULATOR LH

a.
C402824N01
0.625,1.531 0.781,1.698 0.156,0.167 10 true A 2.688,0.458 2.844,0.625 0.156,0.167 10 true B 2.219,0.083 2.375,0.25 0.156,0.167 10 true C 1.281,1.938 1.438,2.104 0.156,0.167 10 true C 0.646,0.417 0.823,0.573 0.177,0.156 10 true D

Install the engine mounting insulator LH to the automatic transaxle case sub-assembly with the 5 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A) → Tighten bolt (D)



Hide 12311A 16.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C402822N01
1.229,0.167 1.396,0.333 0.167,0.167 10 true A 2.219,1.917 2.385,2.083 0.167,0.167 10 true B 0.781,1.167 0.948,1.333 0.167,0.167 10 true C

Install the transverse engine engine mounting bracket to the transaxle housing with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A)



Hide 12361 17.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.
C408666

Install the front engine mounting insulator to the transverse engine engine mounting bracket with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 11363A 22.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 23.CONNECT WIRE HARNESS (for RHD)

a.
C402818

Engage the wire harness clamp to connect the wire harness to the automatic transaxle assembly.


b.

Install the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

for Transfer (GF2A):

i.

Engage the 9 wire harness clamps and transfer wire harness connector to connect the wire harness.

C408422


ii.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



d.

for Transfer (GF1A):

i.

Engage the 8 wire harness clamps to connect the wire harness.

C407375


ii.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



e.

Connect the wire harness to the rack and pinion power steering gear assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C407374


f.

Connect the rack and pinion power steering gear assembly connector.

NOTICE:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



g.
C402815

Engage the wire harness clamp and connect the vacuum switching valve (for active control engine mount system) connector.


h.
C402814

Connect the park/neutral position switch assembly connector.


i.
C402830

Connect the connector of the transmission wire connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



Hide 24.CONNECT WIRE HARNESS (for LHD)

a.
C402818

Engage the wire harness clamp to connect the wire harness to the automatic transaxle assembly.


b.

Install the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

for Transfer (GF2A):

i.

Engage the 10 wire harness clamps and transfer wire harness connector to connect the wire harness.

C408421


ii.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



d.

for Transfer (GF1A):

i.

Engage the 9 wire harness clamps to connect the wire harness.

C402817


ii.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



e.

Connect the wire harness to the rack and pinion power steering gear assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C402829


f.

Connect the rack and pinion power steering gear assembly connector.

NOTICE:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



g.
C402815

Engage the wire harness clamp and connect the vacuum switching valve (for active control engine mount system) connector.


h.
C402814

Connect the park/neutral position switch assembly connector.


i.
C402830

Connect the connector of the transmission wire connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



Hide 45319 25.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

Hide 35104V 26.INSTALL BREATHER PLUG HOSE

a.
C364011C01
1.688,0.438 2.24,0.438 false 1.167,1.396 1.719,1.396 false 1.531,0.375 1.844,0.531 0.313,0.156 10 false *1 1,1.323 1.313,1.479 0.313,0.156 10 false *2
*1 Breather Plug Sub-assembly
*2 Breather Plug Hose


Install the breather plug sub-assembly to the breather plug hose.


b.
C402812

Install the breather plug hose to the No. 1 breather plug (ATM).


c.

Engage the 2 hose clamps to connect the breather plug hose.


Hide 16260 27.CONNECT WATER BY-PASS HOSE ASSEMBLY

Hide 16261G 28.INSTALL FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 29.CONNECT VACUUM HOSE

a.

Engage the 5 clamps to connect the vacuum hose to the automatic transaxle assembly.

C402810


b.
C402809

Connect the vacuum hose to the vacuum hose connector.


Hide 32101A 30.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Remove any remaining adhesive from the 6 drive plate and torque converter assembly setting bolts.


b.
P000601C22
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.



c.
C402807

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black-colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver-colored drive plate and torque converter assembly setting bolts.



Hide 11361J 31.INSTALL FLYWHEEL HOUSING UNDER COVER

Hide 32.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 33.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION