Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL (for RH Side)
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0370712 DIFFERENTIAL OIL SEAL(for RH Side) A

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL(for RH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during differential side oil seal and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
for GF2A:

Front 4WD linear solenoid (transfer assembly)


·

ECU Data Initialization

·

Disconnect System Function Check


Dynamic torque vectoring AWD system (Click here)
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 43457 2.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 41110G 3.REMOVE DIFFERENTIAL SIDE OIL SEAL

a.
C402799C01
0.75,0.417 0.917,0.417 0.917,0.417 2.083,1.042 true 0.542,0.333 0.708,0.5 0.167,0.167 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the differential side oil seal from the transaxle housing.

NOTICE:

Be careful not to damage the front differential case or transaxle housing.



Hide 43410M 4.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C402800N01
0.667,1.667 1.083,1.667 false 0.333,1.583 0.75,1.75 0.417,0.167 10 false SST

Using SST, remove the front drive shaft oil seal RH from the front differential case.

SST
09308-00010  

NOTICE:

Be careful not to damage the front differential case.



Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C402801C01
2,1.667 1.5,2.417 1.5,2.417 2.417,1.917 true 2.219,2.563 2.385,2.729 0.167,0.167 10 false *a 1.167,2.333 1.583,2.5 0.417,0.167 10 false SST
*a Depth


Coat the lip of a new front drive shaft oil seal RH with MP grease.


b.

Using SST and a hammer, install the front drive shaft oil seal RH to the front differential case.

SST
09950-60011  (09951-00410)
09950-70010  (09951-07200)

Standard Depth:

21.5 to 22.5 mm (0.846 to 0.886 in.)


NOTICE:
·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.

·

Do not remove the grease from the lip of the front drive shaft oil seal RH.




Hide 41110G 6.INSTALL DIFFERENTIAL SIDE OIL SEAL

a.

Coat the lip of a new differential side oil seal with MP grease.


b.
C402802C01
0.75,2.063 0.927,2.667 0.927,2.667 1.083,1.75 true 2.25,2.542 2.417,2.708 0.167,0.167 10 false *a 0.833,2.708 1.25,2.875 0.417,0.167 10 false SST
*a Depth


Using SST and a hammer, install the differential side oil seal to the transaxle housing.

SST
09649-17010  
09950-70010  (09951-07200)

Standard Depth:

5.5 to 6.5 mm (0.217 to 0.256 in.)


NOTICE:
·

Make sure to install the differential side oil seal as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the differential side oil seal.

·

Do not install the differential side oil seal at an angle.

·

Do not remove the grease from the lip of the differential side oil seal.




Hide 43457 7.INSTALL DRIVE SHAFT BEARING BRACKET